Sharif Digital Repository

The dynamic characteristics of functionally graded (FG) metal foam cylindrical micro-scale shells in contact with a moving load will be analyzed thorough this paper accounting for strain-gradient size-dependency. In the material structure of a metal foam, pores can diffuse uniformly or non-uniformly. Based upon Laplace transform, the dynamical governing equations of the first-order micro-shell model can be established in a new domain. In order to go back into the time domain, an inverse Laplace transform will be required. Thus, on can express the time response or dynamic deflection of the micro-shell under moving load. In the presented results, it is easy to see the prominence of... 

Noise analysis techniques including Feynman-α (variance-to-mean) and Rossi-α (correlation) have been simulated by MCNP computer code to calculate the prompt neutron decay constant (α0), effective delayed neutron fraction (βeff) and neutron generation time (Λ) in a subcritical condition for the first operating core configuration of Tehran Research Reactor (TRR). The reactor core is considered to be in zero power (reactor power is less than 1 W) in the entire simulation process. The effect of some key parameters such as detector efficiency, detector position and its dead time on the results of simulation has been discussed as well. The results of proposed method in the current study are... 

This paper presents a new approach for fuel burn up evaluation and radioactive inventory calculation used in Tehran Research Reactor. The approach is essentially based upon the utilization of a program written by C# which integrates the cell and core calculation codes, i.e., WIMSD-4 and CITVAP, respectively. Calculation of fuel burn up and radioactive inventories has been done for 26 core configuration of Tehran Research Reactor with HEU fuel element. The present inventory and fuel enrichment of each fuel element have been calculated  

The nitrate-citrate gel exhibits auto-catalytic behavior, which can be used to synthesize nanocrystalline YIG powders. In this study, yttrium iron garnet (Y3Fe5O12) nanocrystalline powders were prepared by a sol-gel auto-combustion process. The influence of metal nitrates to citric acid molar ratio (MN/CA) of the precursor solution on the combustion behavior and crystallite size of synthesized powders was investigated by scanning electron microscopy (SEM), thermal analyses (DTA/TGA) and X-ray diffraction (XRD). The results show that with increasing MN/CA value, the combustion rate increases and the single-phase YIG forms at a higher temperature. The crystallite size of the single phase YIG... 

In this study, the fatigue behavior of composite reinforced cracked aluminum 1050 plates is investigated experimentally and numerically. The tests are conducted in four different stress ratios between 0 and 1. At first step, plates with similar cracks and geometries have been prepared. Then the glass/epoxy patches have been attached to the cracked plates using Araldite 2015 adhesive. Fatigue load has been applied to three cases of samples including non-patch, one-side patch and two-side patch, where in all stress ratios the maximum force is considered constant. A three-dimensional finite element analysis is developed in ABAQUS. A good correlation between finite element results and the... 

Nanocrystalline Y3-xMMxFe5O12 powders (MM denotes Misch-metal, x = 0.0, 0.25, 0.5, 0.75, and 1.0) were synthesized by a sol-gel combustion method. Magnetic properties and crystalline structures were investigated using X-ray diffraction (XRD), a vibrating sample magnetometer (VSM), and a scanning electron microscope. The XRD patterns showed that the single-phase garnet of Y3-xMMxFe5O12 was formed at x values ≤ 1.0. The saturation magnetization of powders increased with decreasing MM content and reached the maximum value at Y3 Fe5O12. The crystallite size of powders calcined at 800°C for 3 h was in the range of 38-53 nm. © 2008 American Ceramic Society  

The nitrate-citrate gels exhibit auto-catalytic behavior, which can be used to synthesize the nanocrystalline YIG powders. In this study yttrium iron garnet (Y3Fe5O12) nanocrystalline powders were prepared by a sol-gel auto-combustion process. The influence of pH value of the precursor solution on the combustion behavior and the garnet phase formation of synthesized powders were investigated by scanning electron microscopy (SEM), thermal analysis (DTA/TGA), infrared (IR) spectroscopy and X-ray diffraction technique (XRD). The results show that with increasing pH value, the combustion rate increases. The as-burnt powder prepared with pH 1 yielded a single phase YIG after calcination at 800... 

In this paper, a two-component Lattice Boltzmann Method (LBM) has been utilized to simulate the natural convection of TiO2-water nanofluid in a curved geometry. The main purpose of this research is to study the effect of nanoparticle size and also boundary conditions on the thermal characteristics of the nanofluid. Furthermore, the effect of Rayleigh number (Ra) and volume fraction of nanoparticles (ϕ) on the average Nusselt number (Nuave) have been investigated. Two different thermal boundary conditions, namely adiabatic and constant temperature, have been considered in the current work for the curved boundaries. The Rayleigh number varies from 103 to 109. Four different sizes, namely 10,... 

The purpose of the present study is to develop the 3D static and noise simulator based on Galerkin Finite Element Method (GFEM) using the unstructured hexahedral elements. The 3D, 2G neutron diffusion and noise equations are discretized using the unstructured hexahedral by considering the linear approximation of the shape function in each element. The validation of the static calculation is performed via comparison between calculated results and reported data for the VVER-1000 benchmark problem. A sensitivity analysis of the calculation to the element type (unstructured hexahedral or tetrahedron elements) is done. Finally, the neutron noise calculation is performed for the neutron noise... 

In the present paper, neutron spectrum is reconstructed using the Artificial Neural Network (ANN) and Modified Least Square (MLSQR) methods. The detector's response (pulse height distribution) as a required data for unfolding of energy spectrum is calculated using the developed MCNPX-ESUT computational code (MCNPX-Energy engineering of Sharif University of Technology). Unlike the usual methods that apply inversion procedures to unfold the energy spectrum from the Fredholm integral equation, the MLSQR method uses the direct procedure. Since liquid organic scintillators like NE-213 are well suited and routinely used for spectrometry of neutron sources, the neutron pulse height distribution is... 

In the present study, the comparison between the results obtained from the linear and quadratic approximations of the Galerkin Finite Element Method (GFEM) for neutronic reactor core calculation was reported. The sensitivity analysis of the calculated neutron multiplication factor, neutron flux and power distributions in the reactor core vs. the number of the unstructured tetrahedron elements and order of the considered shape function was performed. The cost of the performed calculation using linear and quadratic approximation was compared through the calculation of the FOM. The neutronic core calculation was performed for both rectangular and hexagonal geometries. Both the criticality and... 

In the present paper, development of the three-dimensional (3D) computational code based on Galerkin finite element method (GFEM) for solving the multigroup forward/adjoint diffusion equation in both rectangular and hexagonal geometries is reported. Linear approximation of shape functions in the GFEM with unstructured tetrahedron elements is used in the calculation. Both criticality and fixed source calculations may be performed using the developed GFEM-3D computational code. An acceptable level of accuracy at a low computational cost is the main advantage of applying the unstructured tetrahedron elements. The unstructured tetrahedron elements generated with Gambit software are used in the... 

This paper presents a developed computational code based on Support Vector Machine (SVM) for reconstruction of energy spectrum of neutron source. To reconstruct unknown energy spectrum using known neutron pulse height distribution, the developed machine is trained by known neutron pulse height distribution of detector and corresponding energy spectrum of neutron source. Validation and testing are the next steps to verify the validity of the calculations done with the developed computational code. The calculated neutron pulse height distributions due to randomly generated energy spectrum using MCNPX-ESUT (MCNPX-Energy engineering of Sharif University of Technology) computational code are used... 

This paper presents the developed computer codes based on the Adaptive Group of Ink Drop Spread (AGIDS) algorithm [1] for the reconstruction of the energy spectrum of the neutron source. The required data are generated via simulation of the neutron pulse height distributions due to randomly generated energy spectra with the MCNPX-ESUT computer code [2]. The simulated neutron pulse height distributions and corresponding randomly generated energy spectra are the input and output data of the developed computer code, respectively. As a case study, the 241Am-9Be neutron source is studied and the simulation of the neutron pulse height distribution of the NE-213 liquid organic scintillator is... 

The purpose of the present study is the presentation of the appropriate element and shape function in the solution of the neutron diffusion equation in two-dimensional (2D) geometries. To this end, the multigroup neutron diffusion equation is solved using the Galerkin finite element method in both rectangular and hexagonal reactor cores. The spatial discretization of the equation is performed using unstructured triangular and quadrilateral finite elements. Calculations are performed using both linear and quadratic approximations of shape function in the Galerkin finite element method, based on which results are compared. Using the power iteration method, the neutron flux distributions with... 

Increasing the heat capacity of heat exchangers is a crucial need for modern devices. The thermal conductivity of the usual fluids and the Nusselt (Nu) number of flows containing such fluids are two bottlenecks in the way of increasing heat delivery in the heat exchangers. For this reason, nanofluids have been introduced. The effect of utilizing a Cu-water nanofluid as a coolant of two hot pipes in a square cavity is investigated numerically with a two-component lattice Boltzmann method. The volume fraction of nanoparticles is assumed to be constant (0.03) while the Richardson (Ri) number varies from 0.02 to 20. Results show that the effectiveness of nanoparticles is better observed in the... 

The use of hybrid renewable energy has increased in recent years due to the growing environmental concerns caused by the consumption of fossil fuels. The purpose of this study was the economic-environmental feasibility of using hybrid energy systems in one of the most polluted and populated provinces in Iran, Isfahan province. Various components of the hybrid energy system such as wind turbine (WT), photovoltaic panel (PV), diesel generator (DG), converter (CV) along with two scenarios of energy storage including battery (BT) and hydrogen storage have been considered in modeling the energy system. Six scenarios were considered based on the combination of different components for supplying...