Sharif Digital Repository

With the progression of technology demands for novel method of heat cooling is increased so the old method of cooling such as heat removal by air stream with force convection and even single phase method was not sufficient for today’s industry need. Nowaday, spray cooling method which belongs to two phase cooling method is one of the most popular method. In this study two method of spray cooling: spray cooling with flow blurring nozzle and electrospray cooling were investigated. For both method, at first the physics of phenomena and morphology of spray is studied experimentally then the efficiency of heat removal in each method is evaluated by the assessment of variation of temperature and... 

Light-sensitive hydrogels are advanced materials with modern applications that have the ability to deform with light radiation at specific frequencies. Numerous studies have been conducted to identify the behavior and deformation of these materials. Most studies have experimentally investigated the light-sensitive behavior of hydrogels. On the other hand, modeling the behavior of light-sensitive hydrogels is very complicated, so that the use of these models is possible only in certain cases. Therefore, in the present study, the existing studies have been reviewed in order to simplify the relationships governing the deformation of light-sensitive hydrogels. In this regard, the deformation... 

Improvement of semiconductors photocatalytic activity by different means has always been one of the challenges for researchers. Semiconductors doping for band-gap engineering and changing morphology to increase specific surface area and photocatalytic reaction sites are amongst these efforts. In this research simultaneous effect of these two parameters for three morphologies containing nanoparticle, nanowire and micro dandelion, simultaneously doped with carbon and nitrogen has been investigated. Final purpose of this thesis is to decrease the band-gap energy close to soft UV photon energies to make surface photodynamic therapy possible. Nanoparticle morphology with size distribution between... 

In this thesis the behavior of a 3D wing has investigated by Flow visualization and pressure acquisition test. The goal of this tests was considering changes in 3D wing section parameter in comparison with 2D airfoils. The performed Tests showed that variation in 3D wing treatment is affected by finite aspect ratio and sweep angle and also indicate changes in pressure profile, increasing pressure peak and decreasing effective speed. CFD studies has conducted to investigate special effect of sweep angle and show that lift and drag coefficient decrease with increasing sweep angle. Also different section pressure profile near the wing tip and intersection of wing/fuselage varies and miss... 

One of the main challenges in characterization and simulation of larg scale porous media is spatial heterogeneity and variability of porous media properties such as porosity, density, and lithology at different scales. These information can be achieved at different scale from coring, well logging or seismic data. Well logs are an efficient way to obtain rock and fluid properties of geological patterns specially water resources and hydrocarbon reservoirs. One of the characteristics of geophysical well logs is their complex behavior which seems to imply a multifractal nature.In this study we investigate multifractality and presence of long range correlations in petrophysical well log data such... 

High efficiency and low-emission fuel cells have the capacity to replace fossil fuels for energy supply concerns. Solid oxide fuel cells operate in relatively high temperature and have power plant applications. Hence, they are acquainted to be coupled with cycle gas turbine to reduce the cost and increase the overall system efficiency. The control of these hybrid systems is so important. Due to the system nonlinearity and having more than one controlled variable, its control with classic methods would be difficult. The model based predictive control is used as an alternative to mitigate these difficulties. In addition to their high performance, their extension to the multivariate case would... 

Numerical study of the interaction mechanism of the premixed flame and the acoustic field is performed in this work. The geometry similar to those used in experiments, is a two-dimensional tube in which flame travels form open end towards the closed end. The numerical study is done using PPM method. Results show that the shape and speed of laminar flame is strongly affected by the induced acoustic field. Stronger interaction is observed in the closed-end tube with no slip boundary conditions. The effect of the Lewis number on the interaction mechanism is also investigated. Premixed flame- accelerated flame – interaction of flame and acoustic field  

Translation quality assessment (TQA) as a systematic field of inquiry has been under scholarly investigation over the past decades. In spite of the challenges appeared in the path to success, theoretical and practical developments have already been made in translation studies. One of the unsettled and challenging problems concerning translation assessment, yet, is the subjectivity that is inherent in the process of scoring test-takers’ translation performances. In the absence of any granular objective criteria which includes all the subcomponents of translation as a multi-layer rather than unitary construct, the raters inevitably bring their intuition and will to the act of measurement.... 

Knowing the location and time of oil accidents and trying to track the pollution caused by these accidents is very important for the purpose of monitoring and protecting the environment. The occurrence of large oil spills in the marine environment can have serious environmental, social and economic consequences. In this research, oil spills in the Persian Gulf were first identified using remote sensing method and Sentinel-1 satellite images. The images of this satellite were called for the processes needed to identify oil spills in Google Earth Engine space. After detecting the oil spills, it is necessary to determine the duplicate spills and remove these types of spills, as well as estimate... 

Primary visual cortex plays a paramount role in processing visual information. Visual information after the primitive processing by LGN and Thalamus, will be sent to the primary visual cortex which is called V1 area. According to the fact that V1 neurons have the definitive sensitivity to the edge and contrast of visual stimuli so their behavior are very selective to the certain features, specially contrast, of visual stimuli. These neurons have different response behavior to contrast. In fact most of them have some nonlinear behavior to this feature. Normally we expect that response of them or spiking rate of them grow linearly by the contrast increases but in most many cases they have some... 

High-quality online services demand reliable and fast packet delivery at the network layer. However, clear evidence documents the existence of compromised routers in the ISP and enterprise networks, threatening network availability and reliability. A compromised router can stealthily drop, modify, inject, or delay packets in the forwarding path to launch Denial-of-Service, surveillance, man-in-the-middle attacks, etc. So researches tried to create intrusion detection methods to identify adversarial routers and switches. To this end, data-plane fault localization (FL) aims to identify faulty links and is an effective means of achieving high network availability. FL protocols use... 

Epoxy resins are used for a wide number of application due to good stiffness, chemical resistant and dimensional stability. This is the reason of their use as matrix in composite material. The incorporation of a small amount of carbon nanotubes (CNTs) in epoxy increases mechanical properties if nanocomposite have strong interfacial interaction between epoxy and CNTs, fine dispersion of CNTs and high final aspect ratio CNTs. In Noncovalent functionalization by polymer surfactant, CNTs are dispersed in a solvent/surfactant solution by ultra-sonication and then added to epoxy. In this thesis a novel study of toughening and mechanical properties of epoxy/ rubber/ CNT nanocomposite is presented.... 

Confining nematic liquid crystal between two curved boundary conditions while the nematic molecules have a degenerate planar anchoring leads to complex and beautiful textures of molecular disparagement(defect) in the bulk and on the surfaces. Such the liquid crystal shells are made with double-emulsion techniques in microfluidic devices have provided applications for micro-scale colloidal linkers.In this work, we have numerically minimized the elastic energy in one-constant approximation in present of Fournier’s degenerate surface potential with finite element method. The nematic shell is confined between two spherical surfaces that we have studied the final energies and their related... 

Nowadays, despite the special position of power electronic converters in the world, and the fact that they become an integral part of human life, still in the wake of a serious necessity the development process has not stopped and the increasingly fast pace, it opens up new horizons. This important necessity emerges from the environmental concerns regarding consumption of fossil fuels and their limited and imbalanced distribution which can be effectively addressed with the use renewable energy systems. By improving the quality of the semiconductor switches and offering new topologies in different functions as well as using new control methods, scholars try to develop enhanced converters in... 

In this thesis, we focus on some internal organization issues of the supply chain; in particular, we analyze some network design problems which are typical of producer companies. The aim is to optimize the flow of goods through the literature distribution network, from the plants where the goods are produced (supply points) to the demand points, which are essentially distributors such as wholesalers or retailers. The system addresses a class of distribution network design problems, which is characterized by multiple product families, a central manufacturing plant site, multiple central warehouses and distribution center, and retail outlets (customer zones) which demand multiple units of... 

The purpose of this research has been measuring how much studied companies use different levers of controls. Management control system has been described as the system which ensures the organization about implementing its strategy (Antony, 2004; Simons, 1995). In this research we chose Levers of Control framework (Simons, 1995) as the proper model to describe management control systems in organizations. Using related literatures, we developed a questionnaire to measure how much different organizations use each levers of control. The proposed questionnaire was distributed in three businesses with different Value Creation Logics (Stabell & Fjeldstad, 1998), to provide a ... 

Popular usage of composite materials in aerospace, civil and defense industries in the last decades has been the cause for paying more attention to optimization of composites tailoring. Due to inherent complexity of composite problems, i.e. discrete nature, complex interrelationship of design variables, existence of so many local optimum points, and etc., gradient base methods of optimization are found to be incapable and as a result using other powerful methods seems inevitable. Nowadays Genetic algorithm (GA) as an evolutionary technique is used for tackling composite problems. The success of a genetic algorithm can be quantified by estimating the cost, time required and the quality of... 

Today, the correct management of construction projects in IRAN's water industry has become a severe concern for its managers. Construction projects of the water industry constitute a considerable part of the country's construction industry. Several significant Issues such as operation management, water industry projects, correct management of resources, crisis management in the water industry, increased productivity and useful life of structures, increasing productivity, and preventing water loss are among the determinative challenges in construction projects in Iran. One of the new methods for the correct management of the life cycle of projects in this area is the use of Building... 

The distinction between SOEs and private firms in access to loans is essential from the viewpoint of policy-making. This distinction is more crucial when we know that the difference is caused by factors other than natural market forces and has emerged merely by government ownership. In this paper, we investigate a unique intervention in privatization and identify the causal effect of government ownership on access to loans. In this respect, we study Sahamedalat in Iran by using DID approach and estimate the effect of giving up the treatment firm's cashflow right on the amount and composition of the loans. The results show the intervention significantly decreases the long-term loan of the...