Sharif Digital Repository

Infill materials in rock joints usually cause a reduction in the joint shear strength. The shear behavior of rock discontinuities depends upon whether they are clean and unfilled or filled, so this concern invites accurate understanding of the shear behavior and strength of infilled joints. A series of constant normal load direct shear tests was performed to investigate the shear strength of artificial samples with infilled rough joint surfaces having different asperity and infill characteristics. The current study focuses on the effects of factors that influence the shear strength of infilled rock joints samples, with emphasis on forward and reverse shearing. In the forward cycle, the front... 

Authentication is an essential security requirement in safety-related vehicle-to-vehicle applications in VANETs. TESLA is one of the most popular broadcast source authentication protocols proposed and standardized for this purpose. Having strict time constraints and being prone to GPS synchronization errors make the analysis of this protocol challenging. In this paper, we utilize a timed model checking approach based on timed colored Petri nets to model and verify TESLA considering its time-sensitive behaviors. In this way, we show how neglecting timing aspects in protocol design and in protocol modelling can lead to successfully launched attacks and erroneous analyses respectively, and how... 

A high-speed current-mode sample-and-hold circuit is presented. This circuit allows for high sampling speed together with high linearity and precision. The sample-and-hold circuit has been designed and simulated in standard 0.18μm CMOS technology with 1.5V supply voltage. It is capable of operation with sampling frequency of 150MHz (300MHz using double sampling technique) for 12-bit accuracy using 3.7mW power  

In a MIMO (Multiple Input Multiple Output) radar system, proper design of transmit signal and receive filter is an advantageous tool to improve the detection performance. Thus, in this paper, we consider the problem of transmit code and receive filter design, in order to maximize the Signal to Noise Ratio (SNR) at the receiver while enforcing a similarity constraint between the transmit space-time code (STC) and a reference STC which has a desirable ambiguity function. We will show that by solving such constrained optimization problem through successive iterations, our proposed method leads to satisfactory results  

Weighting elements to achieve radiation patterns with desired characteristics is a classical work in phased array antennas. These characteristics can be low sidelobe level, narrow beamwidth, high directivity, pattern nulling in special angle and etc. For each of these characteristics, different methods have been introduced. Most of methods have been presented for uniform arrays, however there are lots of methods to obtain a desired pattern for antennas with non-uniform element distances. The problem with these methods is complexity or not very good results. In this paper, fast and easy methods based on Least Square Error that leads to good results are presented. In addition, weighting of... 

Distributed generation connected with AC, DC, or hybrid loads and energy storage systems is known as a microgrid. Campus microgrids are an important load type. A university campus microgrids, usually, contains distributed generation resources, energy storage, and electric vehicles. The main aim of the microgrid is to provide sustainable, economical energy, and a reliable system. The advanced energy management system (AEMS) provides a smooth energy flow to the microgrid. Over the last few years, many studies were carried out to review various aspects such as energy sustainability, demand response strategies, control systems, energy management systems with different types of optimization... 

This paper resolve the salinity-dependent interactions of polar components of crude oil at calcite-brine interface in atomic resolution. Molecular dynamics simulations carried out on the present study showed that ordered water monolayers develop immediate to a calcite substrate in contact with a saline solution. Carboxylic compounds, herein represented by benzoic acid (BA), penetrate into those hydration layers and directly linking to the calcite surface. Through a mechanism termed screening effect, development of hydrogen bonding between –COOH functional groups of BA and carbonate groups is inhibited by formation of a positively-charged Na+ layer over CaCO3 surface. Contrary to the common... 

An important tool for assessing a radar's performance is the ambiguity function. On the other hand, many different schemes have been designed for the transmit waveforms of a MIMO radar. For each one, a criterion has been chosen to improve the performace, e.g. achieving better missed detection. In this paper, considering the ambiguity function as the benchmark, we propose a waveform design scheme, which optimizes the ambiguity function of the MIMO radar system  

Flow hydrodynamics of laminar falling film of aqueous Li Br solution (Li Br - H2O) on a horizontal elliptical tube has been investigated in this research. The film velocity distribution and film thickness, namely, the flow characteristics are determined by solving analytically simultaneous simplified Navier - Stokes equations and continuity equation in polar and Cartesian coordinates. The analysis is based on steady state laminar flow of falling liquid film of Li Br - H2O on a horizontal elliptical tube in polar model and Cartesian model (CM), for cases in which traction on the film surface is considered negligible. Models are compared with each other in three cases of aspect ratios (Ar),... 

Velocity distributions in (r,θ) directions are evaluated by solving simultaneous simplified Navier-Stokes equations (NSE) and continuity equation (CE) in polar coordinate. The analysis is based on steady state laminar flow of thin falling liquid film on a horizontal circular tube, for cases in which traction on the film surface is considered negligible. It is a common geometry for part of engineering problems such as evaporator, condenser, absorber, generator of absorption chillers and other similar units in mechanical and chemical engineering. Knowledge of the velocity profiles is usually needed for: 1 - solving governing energy and species equations 2- estimating the average and film... 

Velocity distributions in (r,θ) directions are evaluated by solving simultaneous simplified Navier-Stokes equations (NSE) and continuity equation (CE) in polar coordinate. The analysis is based on steady state laminar flow of thin falling liquid film on a horizontal circular tube, for cases in which traction on the film surface is considered negligible. It is a common geometry for part of engineering problems such as evaporator, condenser, absorber, generator of absorption chillers and other similar units in mechanical and chemical engineering. Knowledge of the velocity profiles is usually needed for: 1- solving governing energy and species equations 2- estimating the average and film... 

This work concerns the experimental investigation of surfactant alternating CO 2 injection in carbonate rocks. The core samples provided from a low-temperature fractured light oil reservoir, located in southwest Iran. The experiments were designed to observe the effect of CO 2-foam injection on gas mobility and oil recovery at different surfactant concentrations. The core samples were initially saturated with synthetic/field brine, 5,000 ppm, and then flooded with live oil to reach connate water saturation at reservoir condition, 115F and 1,700 psia. The commercial surfactant used was sodium lauryl sulfate as an anionic surfactant. The results of this work, along with field-scale simulation... 

Knowledge of Air-water two phase flows is significant to different engineering systems such as chemical reactors and power plant and petrochemical and petroleum industry. One of the most industrial cases of two phase flow is two phase flow in vertical large pipes. In this paper in order to find two phase flow behavior along vertical large diameter pipes we simulate air inlets with different number of holes and different hole diameters in the same flow rate of air. In addition, flow characteristics such as cross-sectional void fraction and velocity and pressure were considered. To achieve this aim, main equations of flow have been developed for investigation of flow behavior in air-water two... 

The present work investigates the thermal performance of a five turn Open Loop Pulsating Heat Pipe (OLPHP). The effects of working fluid namely water and ferrofluid, heat input, ferrofluid concentration, charging ratio, and orientation will be considered. Experimental results show that using ferrofluids can enhance the thermal performance in comparison with the case of distilled water. In addition, applying a magnetic field on the OLPHP charged with ferrofluid reduces its thermal resistance. Variation of the ferrofluid concentration results in different thermal performance of the OLPHP. Best charging ratio for the distilled water and ferrofluid without magnetic field is 60 % in most of the... 

Accurate estimation of the capacity curve of offshore jacket structures to achieve performance levels and ductility is of great importance. Proper modeling of compressive members to correctly investigate global and local buckling is crucial in estimation of the capacity curve. Buckling modes and deformations due to local buckling can be considered, if the compressive braces are modeled by shell or solid elements. The purpose of this paper is to achieve the correct compressive behavior of braces with solid type elements and investigate the effects of five different parameters such as D/t, L/D, mesh size, mesh size ratio, and imperfections. ABAQUS FE software is used for this purpose. The... 

Accurate estimation of the capacity curve of offshore jacket structures to achieve performance levels and ductility is of great importance. Proper modeling of compressive members to correctly investigate global and local buckling is crucial in estimation of the capacity curve. Buckling modes and deformations due to local buckling can be considered, if the compressive braces are modeled by shell or solid elements. The purpose of this paper is to achieve the correct compressive behavior of braces with solid type elements and investigate the effects of five different parameters such as D/t, L/D, mesh size, mesh size ratio, and imperfections. ABAQUS FE software is used for this purpose. The...