Loading...
Search for:
jalaly--sadegh
0.112 seconds
Analysis and Design of the Dielectric Resonators Using Differential Transfer Matrix Method (DTMM) in the Cylindrical Coordinate
, M.Sc. Thesis Sharif University of Technology ; Mehrany, Khashayar (Supervisor)
Abstract
Ring and disk resonator are studied in this thesis. First, the complex resonance frequencies of two-dimensional homogeneous ring and disk resonators are extracted by following the standard approach and then a novel method is proposed to extract the complex eigen-frequencies of two-dimensional inhomogeneous ring and disk resonators. The inhomogeneity of the refractive index is arbitrary along the radial direction. The proposed method is shown to be more efficient than the standard approach based on the stair-case approximation. It is therefore appropriate for resonator design and is thus employed for systematic study of the opposing trends of geometrical parameters in maximization of...
Opposing trends of geometrical parameters in maximisation of micro-ring resonator quality factor
, Article Electronics Letters ; Volume 47, Issue 25 , 2011 , Pages 1388-1390 ; 00135194 (ISSN) ; Rezaei, M ; Mehrany, K ; Sharif University of Technology
2011
Abstract
Opposing trends of geometrical parameters in minimisation of bending loss and thus in maximising the quality factor are briefly discussed for micro-ring resonators. It is shown that, while the quality factor of low order modes is an oscillatory function of geometrical parameters, the quality factor of high order modes is a monotonic function. The former has discrete pairs of optimum inner and outer ring radii which maximises the quality factor. In contrast, the quality factor of the latter has no local maximum. Introduction of slight inhomogeneities does not change the overall behaviour of the quality factor but can increase its overall level when the refractive index of the ring region...
QSAR Study of Chromenes & Carboxamides as Anti-Breast Cancer Drugs
, M.Sc. Thesis Sharif University of Technology ; Jalaly Heravi, Mahdi (Supervisor)
Abstract
Breast Cancer is considered one of the most common cancers among Iranian women. Every year, seven thousands women start suffering from this disease. Since 70 percent of this patients live over 5 years, after this disease starts, there are 70 thousands women who are suffering from the cancer. The average age of getting the disease in Iran is 5 years lower than that of the global level. Studies show that compound containing Chromene and Carboxamides are appropriate candidates for preventing breast cancer. One of the most important fields of researches in Chemistry and Bio-Chemistry is QSAR which is used to relate the structure of molecules to their activities. In this study, molecular...
Effecive & efficient DSM configuration guidelines for low-cost development of complex systems
, Article Gain Competitive Advantage by Managing Complexity - Proceedings of the 14th International Dependency and Structure Modelling Conference, DSM 2012, 13 September 2012 through 14 September 2012 ; 2012 , Pages 125-137 ; 9783446433540 (ISBN) ; Sharif University of Technology
Institution of Engineering Designers
2012
Abstract
With the proliferation of more complex systems has come the need to find better solutions in both technical and management domains. Such complex systems are usually larger in size, have more parallel operations and contain more complex interfaces (Eisner, 2005). The Design Structure Matrix is a very useful tool in handling such complexities, provided that the system designer can use it properly. This paper addresses how effectiveness & efficiency are defined for a DSM and how these two important characteristics can be achieved. The importance of understanding the solution space in constructing an effective & efficient DSM is discussed and general guidelines are given on configuring the DSM...
Thin Film Thickness Measurement Using Colors of Interference Fringes
, M.Sc. Thesis Sharif University of Technology ; Amjadi, Ahmad (Supervisor)
Abstract
There are several methods for measuring thin film thickness, however, for the analysis of liquid film motors [1] we need a method which is capable of measuring the thickness using a single image of the film. In this work, we use the colors that appear on thin films, such as soup bubbles, which is a result of light interference to calculate the thickness of the layer
Measure for Macroscopic Quantumness via Quantum Coherence and Macroscopic Distinction
, M.Sc. Thesis Sharif University of Technology ; Raeisi, Sadegh (Supervisor)
Abstract
One of the most elusive problems in quantum mechanics is the transition between classical and quantum physics. This problem can be traced back to the Schrodinger's cat. A key element that lies at the center of this problem is the lack of a clear understanding and characterization of macroscopic quantum states. Our understanding of Macroscopic Quantumness relies on states such as the Greenberger-Horne-Zeilinger(GHZ) or the NOON state. Here we take a first principle approach to this problem. We start from coherence as the key quantity that captures the notion of quantumness and demand the quantumness to be collective and macroscopic. To this end, we introduce macroscopic coherence which is the...
Structural Health Monitoring using Bayesian Optimization of the finite element model of structures and Kalman filter
, M.Sc. Thesis Sharif University of Technology ; Bakhshi, Ali (Supervisor)
Abstract
With confidence in the recorded observations, the RLS method no longer estimates the recorded measurements by sensors, i.e. the displacement and speed of the floors, and only estimates the parameters. In contrast, in the EKF method, in addition to estimating the structure's parameters, a more precise estimation of the observations recorded by the sensors has been done by accepting the noise in the recorded observations. These methods, which are based on the Bayesian updating, investigate the two primary sources of uncertainty in a problem: a) measurement noise or observation noise, and b) process noise, which includes modeling errors. In these methodologies, the unknown system parameters,...
Finding Semi-Optimal Measurements for Entanglement Detection Using Autoencoder Neural Networks
, M.Sc. Thesis Sharif University of Technology ; Raeisi, Sadegh (Supervisor)
Abstract
Entanglement is one of the key resources of quantum information science which makes identification of entangled states essential to a wide range of quantum technologies and phenomena.This problem is however both computationally and experimentally challenging.Here we use autoencoder neural networks to find semi-optimal measurements for detection of entangled states. We show that it is possible to find high-performance entanglement detectors with as few as three measurements. Also, with the complete information of the state, we develop a neural network that can identify all two-qubits entangled states almost perfectly.This result paves the way for automatic development of efficient...
Numerical Analysis and Optimization of A Vortex Tube with Differential Evolution Algorithm
, M.Sc. Thesis Sharif University of Technology ; Mazaheri, Karim (Supervisor)
Abstract
The vortex tube is a simple device that injects compressed gas (air) tangentially into the vortex chamber through one or more injection nozzles. After entering, the flow becomes rotational and an axial cold flow goes towards the cold outlet and a peripheral hot flow goes towards the hot outlet. Besides all the different applications of the vortex tube, the main application of this device is cooling. Here, the goal is to optimize the geometry and physical conditions to improve the performance, which is done by using a commercial software and numerical analysis of a vortex tube to understand the flow physics and optimization. In this research, we use experimental and numerical data for...
Natural convection from a confined horizontal cylinder: The optimum distance between the confining walls
, Article International Journal of Heat and Mass Transfer ; Volume 44, Issue 2 , 2001 , Pages 367-374 ; 00179310 (ISSN) ; Razi, Y. P ; Sharif University of Technology
2001
Abstract
The laminar natural convection from an isothermal horizontal cylinder confined between vertical walls, at low Rayleigh numbers, is investigated by theoretical, experimental and numerical methods. The height of the walls is kept constant, however, their distance is changed to study its effect on the rate of the heat transfer. Results are incorporated into a single equation which gives the Nusselt number as a function of the ratio of the wall distance to cylinder diameter, t/D, and the Rayleigh number. There is an optimum distance between the walls for which heat transfer is maximum. © 2000 Elsevier Science Ltd. All rights reserved
Content Based Community Extraction in Social Networks from Stream Data
, M.Sc. Thesis Sharif University of Technology ; Abolhassani, Hassan (Supervisor)
Abstract
Increasing in social communication via electronic ways has been made social network analysis of these communications more important each day. One of the most important aspects in social network analysis is community detection in such networks. There are many different ways to extract communities from social graph structure which in some of them the content of communication between actors has been noticed in community extraction algorithm. In this thesis after a short survey over advantages and disadvantages of existing methods for community detection, a new method for extracting communities from social networks has been suggested which in addition to streaming property of data it spot the...
Quantum Information Processing with NMR Spectroscopy
, M.Sc. Thesis Sharif University of Technology ; Raeisi, Sadegh (Supervisor)
Abstract
Quantum Information Processing (QIP) is one of the active areas of research in both theoretical and experimental physics. Any experimental technique that is used for a scalable implementation of QIP must satisfy DiVincenzo’s criteria [17]. Nuclear Magnetic Resonance (NMR) satisfies many of these conditions, but it is not scalable and cannot initialize the qubits to pure state [28]. NMR can be a great platform for studying the fundamentals of QIP. In this project, for a twoqubit system, we prepare pseudo pure states from the initial mixed states by using unitary operations and implement CNOT gates. According to the results of our experiments, we can apply all the gates with high fidelity....
Naturality of network creation games, measurement and analysis
, Article Proceedings of the 2012 IEEE/ACM International Conference on Advances in Social Networks Analysis and Mining, ASONAM 2012 ; 2012 , Pages 716-717 ; 9780769547992 (ISBN) ; Fahmi, Z ; Fazli, M ; Habibi, J ; Jalaly, P ; Safari, M ; Sharif University of Technology
2012
Abstract
Modeling is one of the major research areas in social network analysis whose goal is to study networks structure and its evolution. Motivated by the intuition that members in social networks behave selfishly, network creation games have been introduced for modeling social networks. In this paper, our aim is to measure how much the output graphs of a given network creation game are compatible with a social network. We first show that the precise measurement is not possible in polynomial time. Then we propose a method for its approximation; finally, we show the usability of our method by conducting experiments on real network data
A coarse relative-partitioned index theorem
, Article Bulletin des Sciences Mathematiques ; Volume 153 , 2019 , Pages 57-71 ; 00074497 (ISSN) ; Esfahani Zadeh, M ; Sadegh, A ; Sharif University of Technology
Elsevier Masson SAS
2019
Abstract
It seems that the index theory for non-compact spaces has found its ultimate formulation in the realm of coarse spaces and K-theory of related operator algebras. Relative and partitioned index theorems may be mentioned as two important and interesting examples of this program. In this paper we formulate a combination of these two theorems and establish a partitioned-relative index theorem. © 2019 Elsevier Masson SAS
On non-progressive spread of influence through social networks
, Article Theoretical Computer Science ; Vol. 550, issue. C , 2014 , pp. 36-50 ; ISSN: 03043975 ; Ghodsi, M ; Habibi, J ; Jalaly, P ; Mirrokni, V ; Sadeghian, S ; Sharif University of Technology
2014
Abstract
The spread of influence in social networks is studied in two main categories: progressive models and non-progressive models (see, e.g., the seminal work of Kempe et al. [8]). While the progressive models are suitable for modeling the spread of influence in monopolistic settings, non-progressive models are more appropriate for non-monopolistic settings, e.g., modeling diffusion of two competing technologies over a social network. Despite the extensive work on progressive models, non-progressive models have not been considered as much. In this paper, we study the spread of influence in the non-progressive model under the strict majority threshold: given a graph G with a set of initially...
Miniaturized salting-out liquid-liquid extraction in a coupled-syringe system combined with HPLC-UV for extraction and determination of sulfanilamide
, Article Talanta ; Vol. 121 , April , 2014 , pp. 199-204 ; ISSN: 00399140 ; Khosraviani, M ; Sadegh Amini-Fazl, M ; Sharif University of Technology
2014
Abstract
In salting-out liquid-liquid extraction (SALLE) technique, water-miscible organic solvents are used for extraction of polar analytes from saline solutions. In this study, for the first time, a coupled 1-mL syringes system was utilized to perform a miniaturized SALLE method. Sulfanilamide antibiotic was extracted and determined via the developed method followed by high performance liquid chromatography-ultraviolet detection (HPLC-UV). The extraction process was carried out by rapid shooting of acetonitrile as extraction solvent (syringe B) into saline aqueous sample solution (syringe A), and then the shooting was repeated several times at a rate of 1 cycle s-1. Thereby, an extremely large...
The effect of additives on anode passivation in electrorefining of copper
, Article Chemical Engineering and Processing: Process Intensification ; Volume 46, Issue 8 , 2007 , Pages 757-763 ; 02552701 (ISSN) ; Yoozbashizadeh, H ; Sadegh Safarzadeh, M ; Sharif University of Technology
2007
Abstract
In copper electrorefining process, some additives are added to the electrolyte to improve the morphology of cathode deposits as well as the quality of products. In the present investigation, the effects of thiourea, glue and chloride ions (as additives) on the passivation of industrial copper anodes under high current densities have been reported. Experiments were conducted at 65 °C; using a synthetic electrolyte containing 40 g/l Cu2+ and 160 g/l H2SO4. Results obtained from chronopotentiometry experiments showed that increasing the concentration of chloride ion leads to increase in passivation time. The results also indicated that from a certain level on, namely 2 ppm, the increase in...
Hierarchical Classification of Variable Stars Using Deep Convolutional and Recurrent Neural Networks
, M.Sc. Thesis Sharif University of Technology ; Rahvar, Sohrab (Supervisor) ; Raeisi, Sadegh (Supervisor)
Abstract
The importance of using a fast and automatic method to classify variable stars for large amounts of data is undeniable. There have been many attempts for classifying variable stars by traditional algorithms, which require long pre-processing time. In recent years, neural networks as classifiers have come to notice. This thesis proposes the Hierarchical Classification technique, which contains several models with the same network structure. Our pre-processing method produces input data by using light curves and the period. We use OGLE-IV variable stars database to train and test the performance of Convolutional Neural Networks based on the Hierarchical Classification technique. We see that...
Redicting Information Reshare by People on Twitter
,
M.Sc. Thesis
Sharif University of Technology
;
Raeisi, Sadegh
(Supervisor)
;
Ghanbarnejad, Fakhteh
(Co-Supervisor)
Abstract
In this thesis, we attempt to construct a model that can predict whether someone will retweet a tweet. For this purpose, we construct a machine learning model and we use Twitter’s network features as our model’s input. We collect about 1300 random tweets and their retweets to make retweet cascades. By collecting or calculating users’ features in each retweet cascade, we construct our desired input data for our model. We test both random forest and neural networks as our machine learning section of the model. Random forest is the most accurate of the two models, predicting retweet actions with an accuracy of 0.89. Additionally, we find out that two features of the network have the greatest...
Numerical Modeling of Turbine Flow Meter and Improving its Performance Using CFD
, M.Sc. Thesis Sharif University of Technology ; Karimi, Mohammad Sadegh (Supervisor)
Abstract
Studying the performance of flow meters is of great importance in order to improve their quality. In this study, we are looking for an optimal design for a turbine flow meter in which the measurement accuracy, pressure drop and response speed indices are improved. For this purpose, a turbine flow meter with a diameter of 2 inches has been selected and its performance has been numerically modeled using computational fluid dynamics in a steady and transient state. By modeling the steady state, the measurement accuracy and pressure drop indices are obtained, and by modeling the transient state, the response time of the flow meter is obtained. In order to increase the accuracy of numerical...