Sharif Digital Repository

Today, due to limited number of light oil reservoirs, enhanced recovery from heavy oil reservoirs is taken into consideration. During the early production from heavy oil reservoirs, due to high viscosity, only a small amount (about 5%) of the oil can be produced; also after water injection operation due to unfavorable mobility ratio of water and oil, sorely more than about 10% of the original oil can be produced. On the other hand, fractured reservoirs represent about 20% of the world's oil reserves, while over 60% of the world's remaining oil reserves are in fractured reservoirs. Water flooding process leaves very high amounts of oil as remaining oil in these reservoirs too. One of the... 

Titanium alloy Ti-6Al-4V ELI with high biocompatibility and corrosion resistance, has a lot of applications in biomedical engineering. Disadvantage of this alloy is it’s disability to create a fast and good contact with the host/bone environment, after implanting in the body. Beside that it has low wear resistance. Nowadays to optimize the wear resistance, bioactivity and osteoconduction of surface of implants which are made from this alloy, the surface morphology are optimized in size and distribution. Different surface treatments are used for producing rough and porous surfaces to improve bioactivity along with wear resistance. In this study, surface modification of Ti-6Al-4V ELI was done... 

Commercially pure titanium (CP-Ti) is an important groups of titanium family and because of high strength, low density, high corrosion resistance and biocompatibility, this group of titanium is a suitable choice for application at chemical, petrochemical and medicine industry. Nowadays surgeons have a tendency toward use of CP-Ti instead of Ti-6Al-4V alloy. Moreover, because of body anatomy limitation, use of thick sheets result in high volume and damage soft tissue. Therefore, for sheet thickness reduction, study of the effects of metallurgical and geometrical parameter on fracture behavior of thin sheets is important. In this study, the fracture behavior of CP-Ti thin sheets investigated.... 

AISI 4340 steel bars were austenitized at 900°C for 1 hour followed by heating at 740°C (ferrite and austenite region) for 100 min and quenching into a salt bath at 300°C for different times followed by quenching into water to obtain triple phase microstructures with 34 Vol.% ferrite and various martensite (or bainite) contents. Presence of three phases in adjacent of each other confirmed by metallographic analysis and TEM technique. Volume fraction of different phases was measured by image analyser. The results of optical microscopy showed that by increasing VM, morphology of martensite varies from uniform distribution of small spherical network particles to large blocky islands with... 

The introduction of multi phase steels in recent years resulted in a considerable increase in development of some industries such as automobiles. By inducing soft and hard phases together, these steels could bring better mechanical properties than classical ones. Recent studies on 4340 ferritic- bainitic and ferritic- martensitic dual phase steels, indicate that 34 volume percent ferrite with hard phase, has the best combination of strength, toughness and fatigue properties. In present research, by proper heat treatment on a 4340 steel, it is tried to prepare specimens ferritic- bainitic- martensitic triple phase steels with 34 volume percent of ferrite and different percents of martensite.... 

In this research, transient liquid phase (TLP) bonding of FSX-414 superalloy was investigated using MBF-80 interlayer. The bonding was performed at different temperatures (1050-1200oC) for various times (1-120min). Also, different gap sizes were studied using the interlayer with various thicknesses (25-100µm). Homogenizing treatment was performed at different temperatures (1175-1225oC) and times (1-6h) for the samples with complete isothermal solidification. The microstructure of the samples were studied using the optical, scanning electron and transmission electron microscopes. Also, XRD, SEM/EDS, SEM/WDS and TEM/EDS analyses were used to analyse the observed phases at the joints. To... 

In the research transient liquid phase bonding of AL6061-SiC composite was performed using copper as interlayer. The joining praocess was performed in various tetemperatures (560c and 580c and 600c) And times (6 and 8 hours). Optimum Joining condition was determined by using optical and of the joint, micro hardness test was performed from the bonding zone to the bulk of the base composite. The fatigue endurance limit of Al6061-SiC composite was determined by several fatigue tests and TLP bonded samples were loaded under achieved endurance limit stress. Finally fatigue fracture surface of both base composite and TLP bonded samples were studied by using of scanning electronic microscope  

Interlayer composition as one of the most important factors of TLP bonding could affect bonding region composition and microstructure that both of them govern the mechanical properties of the joint. Due to the risk of substrate microstructure degradation , welding of dual phase steel needs more cautions. TLP bonding ideally acquires joints having more similar microstructure to substrate. Moreover , using this method could avoid the change of base metal microstructure when heat treatment of carbon steel is postponed until after bonding. Fe-based , Ni-based and commercially pure Cu are three different composition has been studied in this work. The bonded samples were investigated by optic and... 

Dual Phase ferritic-martensitic steels are kind of high strength low alloy steels (HASLA) which are widely used in industry because of their strength and formability. Since welding of dual phase steels in conventional welding methods causes structural change and Subsequently alters mechanical properties of both weld zone and heat affected zone(HAZ), additional operations which are not commercially viable is needed to achieve a dual phase structure in structurally changed regions. In this study, transient liquid phase (TLP) bonding method is used during dual phasing process in order to preserve dual phase ferritic-martensitic structure and avoid extra heat treatment. Applied pressure during... 

Stainless steels have many applications in different industries like chemistry, medicine and food production. So for using these alloys it is necessary to join them with appropriate method. In this research, microstructure-mechanical properties relationship of 304LC austenitic stainless steel transient liquid phase bonded using a Co-based interlayer was investigated. For this purpose, bonding was conducted at 1180 ℃ for different holding times. Microstructure of the joints was evaluated by optical microscopy (OM) and Scanning Electron Microscopy (SEM). The results showed that isothermal solidification (IS) was completed within 1800s and no intermetallic compound was formed in the joint area... 

After World War II, steel bearings containing copper element have been developed by the Navy of the United States of America with the HSLA-100 brand. Since 1890 and in order to manufacture tanks and tools for the body of navy equipment, the steel HY 80 was used instead of HSLA-100. Because of the high carbon content, the welding properties of the HY 80 are low. Furthermore, increasing of hardness and decreasing of toughness in the heat-affected zone generated during the welding process lead to susceptibility of this alloy to hydrogen cracking and brittle fracture. Therefore, in order to minimize the cost of welding, low-alloy high strength steel (HSLA) is used which contain copper. Reducing... 

Cooling sandwich panels are one of the components of the heat exchangers used to cool the components of the sandwich panels . One of the applications of TLP Bonding for steel can be called cooling sandwich panels. In this research , TLP of 304 Stainless Steel , using Fe-base interlayer at 1200 C has been investigated . Cross section of bonded samples were examined by optical and scanning electron microscopes. Microscopy results revealed that 2h is sufficient for completion of isothermal solidification and there is no eutectic compound at bonding zone . Bonding in this condition resulted in the free precipitates in the diffusion affected area. By analyzing eutectic phase in bonding areas at... 

Transient liquid phase bonding of AISI 304 was carried out in a vaccum furnace using a Ni-based interlayer. The effect of bonding time on microstructure and mechanical properties of joints at temperature of 1150 ⁰C was investigated. The results showed that isothermal solidification was completed within 20 min and eutectic phase disappeared across the joint region. The joints with complete isothermal solidification were homogenised for 180 min at temperature of 950 ⁰C. The results of shear test showed that the average shear strength of homogenised samples was about 83% thet of the base metal at the same heat treatment cycle. Corrosion behavior of the TLP bonded and base metal was studied at... 

In this project we investigate the effect of coupling of the inflaton with light particles which have oscillating mass that depends on inflaton. As the inflaton slowly rolls towards the minimum of its potential, the mass of other particles changes periodically(monodromy). The monodromy structure with tuning the parameters of model allows us to produce ultrarelativistic particles during inflation. These particles dilute with the expansion of the universe but continuous particle production leads to burst of particles at the end of inflation. It should be noted that other Warm Inflation models are phenomenological models which is assumed that during the inflation, the inflaton energy is... 

Inflation first introduced for solving the puzzles of the standard model of cosmology. Soon it became clear that this paradigm can provide a natural way for production of Initial conditions for the birth of large-scale structures: cosmological perturbations. But inflationary models are usually phenomenological models. They are constructed to solve the problems of the standard model of cosmology and explain the properties of cosmological fluctuations. Where do they come from? A property of a big family of inflationary models is the flatness of their potential. What would may be the cause of this flatness? . . .. In this thesis our purpose is searching about one probable field theoretic root... 

In this thesis, in order to improve the performance of the mobile robot navigation, a Fuzzy approach is used for making a safe path in the cluttered environment with hurdles in the work space of the robot. To this end, based on data collected from instantaneous location of the robot and location of the robot, heuristic rules are extracted. Also, in order to obtain optimal data fusion of the sensors, Kalman filter is used to localize the robot. In this regards, by using the kinematics of the robot and supposing the white noise in the process and measurements, the position and orientation of the mobile robot are estimated in a real-time and adaptive manner  

The studied steel was AISI 4340 steel. In order to obtain dual-phase steel with a volume fraction of 60, 66 and 75% bainite, samples were heated in the α+γ region at temperatures of 730, 735 and 740 oC for 120 minutes and then to create lower and upper morphology of bainite, samples were transferred directly to salt bath at different target temperatures (300 oC and 400 oC) and kept 60 minutes. Also, to produce a Martemper microstructure, the full martensitic sample was tempered at 260 oC for 90 minutes. Tensile and hardness tests revealed that with the increasing volume fraction of lower bainite, yield strength, tensile strength, and hardness increased from 986 to 1211 MP, 1185 to 1519, and... 

In this study, the effect of martensite volume fraction on the wear behaviour of 4340 steel with triple-phase steel microstructure with a constant volume fraction of 34% ferrite was investigated. Using the Holman equation, it was found that triple-phase steel with different martensite volume fraction has two stages of work hardening. By increasing martensite volume fraction, yield strength and ultimate tensile strength and work hardening exponent of first and second stages increase and the elongation decreased. To perform the wear test, the pin on disc apparatus was used according to the ASTM G99 standard, and the test was done at two forces of 10 and 50 N at a fixed distance of 400 m. The... 

The repair and production of Ni-based and Co-based superalloy parts have high importance in Oil and Gas, and Aerospace industries. Due to this issue, Transient Liquid Phase bonding is one of the most reliable welding methods for repair parts and fabricating new parts.In the present study, creep properties of similar transient liquid phase bonding of FSX-414 Co-based superalloy has been investigated and compared with creep properties of the un-bonded base metal. Firstly, the optimum condition of the bonding process was resulted from microstructural observations from different bonding conditions. Then, cylindrical samples for the aim of creep test specimens were fabricated in two different... 

The inflation paradigm solves the so-called flatness problem of the standard cosmo- logical model and explains the homogeneity of the Universe by adding a period of exponential expansion at early times to the standard scenario. Moreover, it provides a mechanism for generating density perturbations, serving as the seed of large-scale structures. One of the successes of inflation is predicting primordial scale-invariant perturbations that agree with the observations of cosmic background radiation. Nev- ertheless, there will be a cold, matter-free universe after exponential expansion, so one needs a process that leads to a hot cosmos containing standard particles after the end of inflation, the...