Sharif Digital Repository

The performance of a quartz crystal microbalance (QCM) used as a sensor/detector relies on the performance and quality of the film coated onto the quartz crystal sensor. This study focuses on the sensor coating preparation for the detection of glycine. Cellulose nanofibrils (CNFs), natural polymers, were coated on a quartz crystal (QC) surface by a spin-coating method. The prepared CNF-coated QC was characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), cyclic voltammetry (CV), Fourier transform infrared spectrophotometry-attenuated total reflectance (FTIR-ATR), Raman spectroscopy, and water contact angle (WCA). The stable and fully covered QCs without further... 

Charge-discharge rate capability is one of the most important properties of cathode materials for lithium batteries, in particular when envisaging high power density applications such as automotive applications. Efforts to modify rate have been carried out by carbon coating and decreasing particle size in order to modify electronic and ionic conductivity. However, this approach cannot justify all experimental data reported in the literature. Here, we investigated the rate capability of cathode materials by considering their density of states (DOS) calculated by several density functional theory (DFT) methods, in both the lithiated and the delithiated case. We suggested that these structures... 

Transition metal lithium orthosilicates are of interest as cathode materials for lithium batteries. Density functional theory (DFT) calculations were performed to evaluate the structural and electrochemical properties of the different polymorphs of Li2MnSiO4. Our computational studies predict superior properties for the Pmn21 polymorph even after extraction of two Li per formula unit. We state that the shortcomings observed for Li2MnSiO4 as a cathode are caused by two mechanisms. Switching of the magnetic state occurs during the first cycles. The subsequent transition, under delithiated conditions, from the Pmn21 or Pmnb polymorphs to the electrochemically weakest P21/n polymorph is the... 

In this paper, similarity solution of free convection from inclined permeable wall embedded in a stratified porous medium is investigated. It is assumed that the heated wall has constant temperature and permeability along the wall is variable. Energy equation and Darcy's law as momentum have been used. Due to similarity solution we consider only large wall inclination angle. Effects of mass flux, permeability variation function, and wall inclination angle on thermal and velocity boundary layer thickness and heat transfer at the wall are investigated. Copyright © 2005 by ASME  

According to the importance of polyanion cathode materials in intercalation batteries, they may play a significant role in energy-storage systems. Here, evaluations of LiMBO3 and NaMBO3 (M = Mn, Fe, Co, Ni) as cathode materials of Li-ion and Na-ion batteries, respectively, are performed in the density functional theory (DFT) framework. The structural properties, structural stability after deintercalation, cell voltage, electrical conductivity, and rate capability of the cathodes are assessed. As a result, Li compounds have more structural stability and energy density than Na compounds in the C2/c frame structure. Cell voltage is increased by increasing the atomic number of the transition... 

Li2MSiO4 (M = Fe, Mn, etc.) are promising cathode materials for Li-ion batteries. One appealing strategy for improving their cathode properties is to develop mixed transition metal compounds. Density Functional Theory calculations were performed to evaluate the structural, magnetic and electrochemical properties of Li2M0.5N 0.5SiO4 compounds. Our theoretical study allows us to individuate the most promising candidates for practical applications in lithium batteries. © 2013 the Owner Societies  

One of the most relevant negative characteristics of high-capacity cathodes for lithium batteries is indeed non-flat voltage-time (V-t) or voltage-capacity (V-C) behaviour during charge-discharge. A clear rationale for this behaviour has not yet been addressed in the literature. Here, by means of density functional theory (DFT) calculations corroborated by basic experimental electrochemical characterization, we investigated both the thermodynamic and the kinetic aspects relevant to voltage variations during charge-discharge of Li2FeSiO4 intended as a model case. A simple physical model allowed us to take into account all the experimental evidence. We suggested that voltage deviations from... 

A novel intelligent semi-active control system for an eleven degrees of freedom passenger car's suspension system using magnetorheological (MR) damper with neuro-fuzzy (NF) control strategy to enhance desired suspension performance is proposed. In comparison with earlier studies, an improvement in problem modeling is made. The proposed method consists of two parts: a fuzzy control strategy to establish an efficient controller to improve ride comfort and road handling (RCH) and an inverse mapping model to estimate the force needed for a semi-active damper. The fuzzy logic rules are extracted based on Sugeno inference engine. The inverse mapping model is based on an artificial neural network... 

Using CNG as an additive for gasoline is a proper choice due to higher octane number of CNG enriched gasoline with respect to that of gasoline. As a result, it is possible to use gasoline with lower octane number in the engine. This would also mean the increase of compression ratio in SI engines resulting in higher performance and lower gasoline consumption. Over the years, the use of simulation codes to model the thermodynamic cycle of an internal combustion engine have developed tools for more efficient engine designs and fuel combustion. In this study, a thermodynamic cycle simulation of a conventional four-stroke spark-ignition engine has been developed. The model is used to study the... 

With the declining energy resources and increase of pollutant emissions, a great deal of efforts has been focused on the development of alternatives for fossil fuels. One of the promising alternative fuels to gasoline in the internal combustion engine is natural gas [1-5]. The application of natural gas in current internal combustion engines is realistic due to its many benefits. The higher thermal efficiency due to the higher octane value and lower exhaust emissions including CO2 as a result of the lower carbon to hydrogen ratio of the fuel are the two important feature of using CNG as an alternative fuel. It is well known that computer simulation codes are valuable economically as a cost... 

Gaining insight into possible vibratory responses of dynamical systems around their stable equilibria is an essential step, which must be taken before their design and application. The results of such a study can significantly help prevent instability in closed-loop stabilized systems by avoiding the excitation of the system in the neighborhood of its resonance. This paper investigates nonlinear oscillations of a rotary inverted pendulum (RIP) with a full-state feedback controller. Lagrange’s equations are employed to derive an accurate 2-DoF mathematical model, whose parameter values are extracted by both the measurement and 3D modeling of the real system components. Although the governing... 

A suction-controlled ring device has been developed to continuously measure the coefficient of lateral soil pressure in deformable unsaturated soil samples from the at-rest to the active condition under application of increasing vertical pressure and controlled matric suction. The device incorporates a thin aluminum specimen ring equipped with horizontal strain gages for recording the lateral soil strains. In addition, a sensor recording water volume changes is utilized to continuously monitor the degree of saturation of the soil sample during tests. The matric suction within the soil texture is controlled using the axis translation technique. In order to verify the performance of the ring... 

We introduce a new smooth, non-toxic, biocompatible method for cross-linking of gum tragacanth (GT), a polysaccharide of natural origin, in order to serve as a new supporting matrix for immobilization systems. The modified gum is used as a matrix for the catalysis of the conversion of benzyl penicillin to 6-aminopenicillanic acid (6-APA) by means of Escherichia coli ATCC11105 with penicillin G acylase (PGA) activity. The results show that GT beads can not only serve as a proper matrix for immobilization, but show enhanced hydrolysis rate and stability compared to other immobilization systems used for this reaction. This signifies the potential of GT as a biocompatible matrix for... 

The Class-E power amplifier has been widely studied and formulated in the literature. Although the majority of reported inductive coupling wireless power transfer (WPT) systems use a class-E power amplifier for driving the primary coil, still there is a lack of a comprehensive study on class-E circuit dedicated to WPT, providing a set of closed form design equations for proper class-E operation. This paper presents the required design equations needed to design a 'true' class-E circuit for WPT applications. Equations for the series-tuned secondary coil WPT system are presented, as well as two different design procedures for the parallel-tuned secondary coil. The derived equations have been... 

Pole Side Impact Tes is one out of three crash tests described by Euro NCAP standard for star rating of a vehicle and is required for assessing the Adult Occupant Protection. In this paper the goal is to determine the crashworthiness of side doors and B pillar in a Pole Side Impact Test based on Euro New Car Assessment Program (Euro-NCAP) using computer and simulation method. In this matter, a vehicle model has been prepared and meshed using Hypermesh and CATIA. The velocity of 29 km/h has been assigned to the vehicle which was on top of a cart while the pole has been assigned as a rigid static object based on Euro NCAP requirements specifically. Results show that different amounts of energy... 

To assess a car under the Euro New Car Assessment Program (Euro-NCAP), Adult Occupant Protection is one out of three parameters which need to be calculated with a weight factor of 50% while the other parameters, Child Occupant Protection and Pedestrian Occupant Protection, have a weight factor of 20%. The Pole Side Impact Test, beside two other tests, Side and Front Impact, is also required to calculate the Adult Occupant Protection. It shows how important the Pole Side Impact Test is and what an effective role it has in the car rating assessment. In this paper, the objective is to evaluate the effect of thickness on the energy absorbed by the side doors and the B pillar and its... 

In Euro NCAP standard, adult protection is one of the most important rating scores with 50% weight factor while child protection and pedestrian protection are accounted into consideration with 20% weight factor. For adult protection testing, three tests are required to perform: (1) side impact, (2) pole impact, (3) front impact. In the side impact test, dummy's head, chest, shoulder, thorax, ribs, abdomen, pelvic and femur must be studied to evaluate the rating score. Crashworthiness of a car during side impact can describe the score rated for that car. In this paper the goal is to determine the crashworthiness of side doors and B-pillar in side impact crash est by simulation using LS DYNA... 

In side impact test which is one out of three tests of Euro NCAP standard, front and rear doors and B pillar are most absorbance parts among vehicle body parts. Passengers are highly in danger while side crash, because of the distance between passenger's head and vehicle body. In this paper effect of material and thickness of doors and B-pillar and their absorbed energy during crash and improvement of its crashworthiness with respect to light weight design are studied using LS DYNA solver. The objective of this paper is to propose a material for doors and B-pillar with a specified thickness to achieve maximum absorbed energy and minimum weight. The shape of the doors and B-pillar remains...