Sharif Digital Repository

To investigate the effects of flow rate, diameter and offset of secondary fuel injection on combustor noise level, pressure fluctuation and NOx emission, four types of injectors were examined in a swirl-stabilized combustor for overall equivalence ratio (Ø) of 0.7 ~ 0.9 and flow rate of secondary fuel (Qsec) from 0.6 to 4.2 L/min. As for the reference injector used in previous related studies, secondary fuel injection of 3.0 L/min is the best condition for the reduction of pressure fluctuation and combustion noise with tolerable NOx emission. For lower secondary fuel rate of 1.8 L/min, reduction of the injection diameter of reference injector results in a better performance in terms of... 

The vapor extraction process (or VAPEX) uses vaporized solvents injected into a horizontal well to form a vapor chamber within the reservoir. Vapor dissolves in the oil and enhances the oil production by decreasing the oil viscosity in heavy oil reservoirs. To evaluate the process we conduct a simulation study on an Iranian heavy oil reservoir called Kuh-e-Mond. In addition, a semi-analytical investigation of the VAPEX process has been performed. The idea is to perform VAPEX simulation for a laboratory model and find a methodology to compare the results of the simulator with the semi-analytical Butler's model. In particular, a semi-analytical dimensionless correlation for production rate... 

Water flooding is being widely used in the petroleum industry and has been considered as a simple inexpensive secondary recovery method. But in fractured formations, existence of fracture system in reservoir rock induces an adverse effect on oil recovery by water flooding. Polymer flooding has been successfully applied as an alternative enhanced oil recovery method in fractured formations. But, the role of fracture geometrical properties on macroscopic efficiency of polymer flooding is not yet well-understood, especially in fractured five-spot systems. In this work five-spot glass micromodel, because of micro-visibility, ease of multiple experimentations and also presence of the unexplored... 

The vapor extraction process (or VAPEX) uses vaporized solvents injected into a horizontal well to form a vapor chamber within the reservoir. Vapor dissolves in the oil and enhances the oil production by decreasing the oil viscosity in heavy oil reservoirs. To evaluate the process we conduct a simulation study on an Iranian heavy oil reservoir called Kuh-e-Mond. In addition, a semi-analytical investigation of the VAPEX process has been performed. The idea is to perform VAPEX simulation for a laboratory model and find a methodology to compare the results of the simulator with the semi-analytical Butler's model. In particular, a semi-analytical dimensionless correlation for production rate... 

In this work, a reliable dimensionless correlation is proposed for prediction of permeability reduction rate in porous media, which is verified by experimental data obtained in this work in glass bead and sand pack as well as the core data from the literature. Although this correlation is based on the data which were obtained in our work in glass bead and sand-packed media at low pressure, it shows considerable flexibility to match with the extracted data for sandstone cores at high pressure, various flow rates, different temperatures and concentrations of calcium, and sulfate ions in brine solutions. In addition, a novel relationship for predicting the rate of precipitation of CaSO4 in... 

In this study, we have utilized 3-D micro-tomography images of real and synthetic rocks to introduce two mathematical correlations which estimate the distribution parameters of 3-D coordination number using a single 2-D cross-sectional image. By applying a watershed segmentation algorithm, it is found that the distribution of 3-D coordination number is acceptably predictable by statistical analysis of the network extracted from 2-D images. In this study, we have utilized 25 volumetric images of rocks in order to propose two mathematical formulas. These formulas aim to approximate the average and standard deviation of coordination number in 3-D pore networks. Then, the formulas are applied... 

Till now, no mathematical model is presented to model the flow under sonic field be applied in fractured reservoirs. This will be more noticeable when we bear in mind that several reservoirs in Middle East region are fractured. In this work the effects of elastic waves on capillary trapping and mobility of Bingham plastic fluids in fractures have been investigated. Eventually, a model for predicting the influence range of the wave in fractured reservoirs is presented. The results of this study clarified that radiation of wave with low frequency and intensity extremely increases the flow rate and decreases the minimum pressure gradient required for flow of Bingham plastic fluids in fractured... 

Typical non-hydrocarbon gases, which have been utilized in miscible and immiscible processes, are carbon dioxide and nitrogen. These gases are usually injected separately and have been rarely utilized together as a tertiary recovery process. In this article, the authors have experimentally focused on sequential carbon dioxide and nitrogen gas injection as a new enhanced oil recovery method. The periodic injections of carbon dioxide and nitrogen have been repeated for six injection pore volumes. Sensitivity analysis of injection pressure, injection volume, and injection rate has also been investigated in core flood experiments. The experimental results have revealed that a sequential miscible... 

Although CO2 injection significantly increases the amount of oil recovered, it can cause asphaltene deposition in oil reservoirs. Asphaltene deposition leads to formation damage, in which treatment is a costly and problematic operation. In this work, impact of asphaltene precipitation and deposition during CO2 injection are investigated for recombined oil both in sandstone and carbonate core samples through dynamic flow experiments. Injection of oil and CO2 was performed simultaneously. Then, pressure drops along the core were recorded continuously to estimate permeability reductions during the experiments. Online viscosity of injected fluid was measured by a designed capillary viscometer.... 

Despite numerous studies, there is a lack of fundamental understanding about the displacement behavior of surfactant-crude oil systems under the influence of different fractures' geometrical properties in five-spot systems. In this work, a series of flow visualization experiments were carried out on one-quarter five spot glass micromodels at various fractures' geometrical properties, such as fracture density and fracture continuity, under oil-wet condition. The influences of injection of Linear Alkyl Benzene Sulfonate and Sodium Dodecyl Sulfate surfactants as well as the effect of fracture geometrical parameters, on macroscopic and microscopic displacement behavior have been investigated.... 

Finger initiation/development at fluid-fluid interface during miscible floods can cause poor displacement efficiency, which is undesirable in enhanced oil recovery processes. In this work, a series of hydrocarbon injection experiments performed on 5-spot glass micromodels that were initially saturated with the heavy crude oil. The fractured micromodels with different fracture geometrical characteristics were used in the tests. High quality image analysis was applied to determine the fluid flow behavior, solvent front movement, and viscous fingering associated with solvent movement in matrix and fractures. Observations showed that higher solvent dispersion in the fractures rather than matrix... 

There are different thermodynamic models that have been applied for modelling of asphaltene precipitation caused by various reasons, such as solvent/CO2 injection and pressure depletion. In this work, two computer codes based on two different asphaltene precipitation thermodynamic models-the first being the thermodynamic micellization model with a different characterization approach and the second being the solid model-have been developed and used for predicting asphaltene precipitation data reported in the literature as well as in the obtained data for Sarvak reservoir crude, which is one of the most potentially problematic Iranian heavy oil reserves under gas injection conditions. For the... 

Despite numerous experimental and modeling studies, the role of temperature changes on phase behavior modeling of asphaltene precipitation and, in consequence, developing of asphaltene phase envelope in heavy crudes, remains a topic of debate in the literature. In this work, a computer code based on the non-isothermal improved solid model has been developed and used for predicting asphaltene precipitation data for one of the Iranian heavy crudes at different levels of temperature and pressure. The parameters of the non-isothermal model were tuned using three onset pressures at three different temperatures, and the asphaltene phase envelope was developed. The results showed that at high... 

Most of the heavy oil reservoirs contain discontinuous shale which affects fluid flow through porous media as well as recovery efficiency during enhanced oil recovery processes. However, the role of shale geometrical characteristics (including orientation, length, discontinuity, and spacing of the shale) on oil recovery remains a topic of debate in the literature, especially during miscible injection of heavy oils and five-spot systems. Here, a series of hydrocarbon solvent injection tests have been performed on various five-spot glass micromodels containing barriers which are initially saturated with heavy oil under fixed flow rate conditions. Oil recoveries as a function of pore volumes of...