Sharif Digital Repository

In this paper, utilizing the non-local theory, the resonant frequency and sensitivity of an AFM microcantilever are investigated. To that end, the governing equation of motion and corresponding boundary conditions are obtained using the variational approach. Afterwards, the resonant frequency and sensitivity of the AFM microcantilever are derived analytically and depicted in some figures versus the contact stiffness of the sampling surface. The results of the current model are compared to those of the classical theory. The comparison shows that the difference between the results of the non-local theory and those of the classical theory is significant when the non-local parameter is high but... 

A simple method for estimating the apparent viscosity of semi-solid alloys was investigated. A drop weight of 50Kg and backward extrusion equipments were used to test the deformation. Backward extrusion was employed in a closed die system due to the very little separation of liquid from solid phases compared with other methods at very high deformation rate. The half of the calculated impact velocity, 700mm/s was considered as an average velocity for deformation during the test, since the slop of the velocity changes against time is constant in the middle stage of the deformation. The initial height of the sample and the thickness of the residual compressed solid at the bottom of the cup were... 

A high quality joint of zinc based pressure die cast alloys can be hardly achieved by conventional fusion welding. In this study, a novel technique to achieve the globular weld structure using stirring the localized semisolid zone during butt joining of Zamak-3 pressure die cast alloy is proposed and effect of welding parameters on mechanical and microstructural properties are investigated. A gas heating system was designed to heat up the nitrogen gas to desired temperature accurately to create a localized semisolid pool. At this stage a fine stirrer was introduced into the weld seam in order to mix the two sides into a single uniform joint. By presented process, globular microstructure of... 

Current studies show a growing interest on transformation induced plasticity (TRIP) in austenitic steels. Most researches are based on inducing plasticity via tensile stresses, so it seems interesting to accomplish these researches by compressive stresses. Rolling process is a suitable choice to make compressive stresses. In present work, the effects of a wide range of rolling strains (5%-60%) at 0 and 24 °C on the austenite to martensite transformation were investigated on high-alloy austenitic steel. For this purpose, XRD, hardness test and magnetic measurements were used. Results show that by increasing the amount of rolling strain, transformation of austenite to martensite generally... 

The present work is focused on the segregation behavior of semi-solid AZ91 magnesium alloy with Ca content. For this purpose a simple back extrusion test was used and the semi-solid billet was fabricated through a cooling slope. Different shear rates were obtained by variation in ram speed and extrusion ratio. Microstructures of the extruded samples were investigated and liquid segregation was described by Darcy's law. Homogeneity was improved by using higher shear rates, produced either by increasing plunger velocity or extrusion ratio, while at very high shear rates the air was entrapped inside the wall of the extruded sample. © 2008 Elsevier B.V. All rights reserved  

Stepped planing hulls have the potential to reach high-speeds in the sea. The step on the bottom of these vessels influence the pressure distribution and thus stability of the vessel, especially in transverse plane. Understanding the behavior of these vessels in a non-zero heel condition is fundamental in the early stage design. In the current paper, numerical simulation of the viscous flow field around a heeled one-stepped planing hull is performed to evaluate influences of the asymmetric planing on the performance of the vessel. The numerical model is validated in two steps. At the first step, performance of a heeled stepless planing hull operating in calm water is simulated using the... 

Computer base and simulation technique have been applied for modeling the semi-solid die filling and part of the solidification process of aluminum A356 alloy. A fairly simple one-phase rheological model has been implemented into a fluid flow finite element software Procast, to solve the partial differential equations. This model is purely viscous nature and is implemented in the power law cut-off model of Procast. The constitutive parameters of this model were determined for a rheocast A356 alloy. Using these parameters and comparing the simulation results with experimental data showed good correlation with the model prediction. The designed die for rheocasting was applied for the... 

Globulization of the grain refined AZ91 magnesium alloy with Ca on a cooling slope was investigated. Dendritic morphology of the grains was transferred into round and well distributed small particles as a result of grain-refinement effect of Ca in the alloy. Semi-solid holding of the alloy was carried out at different temperatures to improve the spherecity of the globules. Results show that, remelting at 540 °C for 30 min provides the best shape factor for the alloy. The study of coarsening kinetic in this alloy showed lower growth rate alternative other research which used same condition for produce semi-solid billet just in using Ca  

Microstructural evolution of the spray atomized and powder thixoformed hyper-eutectic A390 aluminum alloy was investigated. The spray atomized powder revealed homogeneous and very fine silicon particles distribution, due to the rapid solidification of the alloy. The semi-solid powders were extruded into a closed die cavity through a hole for the plastic deformation of the powder particles. A drop forge of 45kg weight at different heights was used in this investigation. Remarkable rearrangement and growth of the silicon rich phase was revealed in the final stage