Sharif Digital Repository

Alumina nanofluids are one of the most useful nanofluids. In order to evaluate the colloidal behavior of nanoparticles in alumina/water nanofluid, the influence of effective factors such as pH, ionic strength and surfactants, was studied. Zeta potential, particle size and turbidity change of each nanofluid was investigated. According to the results for 0.05, 0.1 and 0.2 mass% nanofluid, point of zero charge was obtained at pH values of 9.5, 10.2 and 10.5, respectively. The highest nanofluid stability occurred at pH 4 and its lowest was at pH 10. The anionic surfactant had a greater effect on the stability in compared with cationic and nonionic surfactants. By increasing in ionic strength,... 

Alumina nanofluids are one of the most useful nanofluids, especially for increasing the thermal conductivity. Due to importance of porous media in the improvement of heat transfer, this study investigates the transport and retention of gamma alumina/water nanofluid in the water-saturated porous media. For this purpose, alumina nanofluids were introduced to the porous media consisting of water-saturated glass beads possessing various pH values (4, 7 and 10) and different ionic strengths (0.001 M of KCl, CaCl2, AlCl3, K2SO4, CaSO4, Al2(SO4)3, K2CO3 and CaCO3). Then the break through curve of each experiment was drawn and modeled by combining classical filtration theory with... 

Alumina nanofluids are one of the most useful nanofluids. In order to evaluate the colloidal behavior of nanoparticles in alumina/water nanofluid, the influence of effective factors such as pH, ionic strength and surfactants, was studied. Zeta potential, particle size and turbidity change of each nanofluid was investigated. According to the results for 0.05, 0.1 and 0.2 mass% nanofluid, point of zero charge was obtained at pH values of 9.5, 10.2 and 10.5, respectively. The highest nanofluid stability occurred at pH 4 and its lowest was at pH 10. The anionic surfactant had a greater effect on the stability in compared with cationic and nonionic surfactants. By increasing in ionic strength,... 

An analytical model is proposed to study the effect of particle size on melting enthalpy and entropy of metallic nanoparticles (NPs). The Mott's and Regel's equations for melting entropy in the combination of core average coordination number (CAC) and surface average coordination number (SAC) of freestanding NPs are considered. Clusters of icosahedral (IC), body centered cubic (BCC), and body centered tetragonal (BCT) structure without any vacancies and defects are modeled. Using the variable coordination number made this model to be in good agreement with experimental and molecular dynamic (MD) results of different crystal structures. The model predicts melting entropy and enthalpy of... 

We present a new TiO2 morphology, featuring high surface area and open structure, synthesized by a two-step chemical route for the manufacture of dye-sensitized solar cells (DSSCs). This construct is sets of intertwined one-dimensional (1D) nanostructures (i.e., nanotubes), so-called skein-like nanotubes (NTs). Such morphology is produced by a combination of TiC oxidation and hydrothermal processes. The mesoporous TiO2 nanoparticles, as the product of TiC oxidation operation, is used as the precursor of hydrothermal process to grow the skein-like NTs. The effect of processing parameters of TiC oxidation and hydrothermal processes is studied. The skein-like morphology enables to eliminate the... 

The objective of this paper is to study the influence of the second peak temperature during real and simulated welding on properties of the subcritically (S), intercritically (IC) and supercritically (SC) reheated coarse grained heat affected (CGHAZ) zones. The X80 high strength pipeline microalloyed steel was subject to processing in a double-pass tandem submerged arc welding process with total heat input of 6.98 kJ/mm and thermal cycles to simulate microstructure of reheated CGHAZ zones. This involved heating to a first peak temperature (TP1) of 1400 °C, then reheating to different second peak temperatures (TP2) of 700, 800 and 900 °C with a constant cooling rate of 3.75 °C/s. Toughness of... 

In this research, Al 3003/Zn sheets with different Zn layer thicknesses (as filler layer) have been soldered to the monolithic Al 3003 sheets. The effects of Zn layer thickness and soldering time at the peak temperature on the joint strength of soldered Al 3003 alloy by pure Zn filler (as the soldering sheets) have been evaluated. Furthermore, microstructure and fracture mechanism of Al 3003/Zn/Al 3003 soldered joints have been studied. The results indicate that by decreasing the Zn layer thickness and increasing the holding time at the peak temperature of soldering, the joint strength improves. Additionally, microscope examinations show that the fracture type of the Al 3003/Zn/Al 3003... 

Spontaneous generation of nanobubbles (NBs) was developed by using a controllable platform of superfast microvortices, based on turbulent jet flows in the presence of graphene oxide (GO) sheets. Very high energy dissipation rates through discharging warm water into cold N2 aqueous solutions resulted in creation of micro/submicro-vortices. Shear stresses in these domains generated gas local supersaturations, leading to the formation of high concentration (∼109 mL−1) of stable NBs. Introducing GO sheets into the microvortex system resulted in effective manipulation of NBs by providing energetically favorable sites for prompt heterogeneous nucleation as well as stronger shear rate fluctuations.... 

Direct oxidation is a simple and effective method for titanium surface treatment. In this research, a titanium sample was directly oxidized at the high temperature in two different atmospheres, air and pure oxygen, to obtain better atmosphere for titanium surface treatment. The results of the Raman spectroscopy indicated that in both atmospheres, the rutile bioactive phase (TiO2) has been formed on the titanium surface. The results of X-ray diffraction (XRD) also revealed that the surface of oxygen-treated sample was composed of the rutile phase and titanium monoxide (TiO), while at the surface of the air-treated sample, the rutile phase and titanium dioxide had been formed. Further, the... 

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled... 

The multistep release of therapeutic agents in the theranostic particulate systems has remained as a challenge in smart drug delivery. In this study, superparamagnetic nanoparticles of Fe3O4 were coated with a blend of F127/F68 grades of pluronic in order to adjust the lower critical solution temperature (LCST) and consequently engineering of the release temperature. Pluronic as a biocompatible thermo-sensitive polymer is frequently used as a self-emulsifying drug delivery system. Magnetite nanoparticles with double layer coating of oleic acid and pluronic F127 have been reported as an on-demand smart carrier for hydrophobic drugs. LCST was examined using differential scanning calorimetry... 

Kinetics of crystallization in an amorphous (Fe0.5Co 0.5)77Si11B9Cu0.6Nb 2.4 (at.%) alloy was investigated using differential scanning calorimetry (DSC). Transformed fraction as a function of temperature was obtained by accurate DSC measurement and the experimental data analyzed with Vyazovkin model-free kinetic method. Reconstructed form of the experimental kinetics model, g(α), clearly showed the crystallization mechanism do not belongs to a single model but almost follows the Avrami-Erofe'ev. Magnetic coercivity and hysteresis loss values of the annealed samples at 823 K were 7.5 A m-1 and 1.2 J m-3, compared to 17.1 A m-1 and 37.1 J m-3 for as spun samples. Magnetic measurements show the... 

Metal–organic frameworks (MOFs) are best known for their great structural diversity. The uniformity in the properties of MOFs is mainly governed by the size and morphology of the particles. In the present research, iron-MIL-88A was prepared by a modulator-assisted solvothermal method, and the role of modulating agents in the formation process of MOF particles was investigated. Acetic acid and formic acid were chosen as monoligand modulating agents. The changes in morphology and size distribution of the products were scrutinized by using SEM micrographs. Both modulators clearly interfered with the crystallization process through their attachment to the reactive sites. At low modulator... 

In this work, nanostructured aluminum titanate (Al2TiO5 or AT) was synthesized by the citrate sol gel method. Then, different volume fractions of this ceramic were blended with Al powder through different durations of the high-energy vibratory milling. The effect of mechanical milling on the thermal degradation of AT in exposure to Al and formation mechanism of in-situ Al2O3 and Al3Ti particles were explored in three conditions: (i) in the powder form; (ii) after annealing of green compact; and (iii) after hot extrusion. In the powder form, it was shown that the mechanical milling is able to significantly diminish the thermal stability of AT, so that the required temperature for the Al3Ti... 

As an alternative to conventional fertilizers, e.g. NPK (the Nitrogen-Phosphorous-Potassium-containing chemical fertilizers) which release their nutrients in a short time glass fertilizers are ideal as they release macro-and micronutrients for crops and plant nourishment more gradually. Also, despite conventional ones, they have no ground-water pollution. In the present study, glass fertilizers were synthesized via polymer-derived ceramics (PDC) method. Despite the melt-casting procedure, PDC needs lower temperatures in heat treatment. The precursors consist of poly-siloxane and active fillers. Thus, thanks to gaseous release during heat treatment of the present active fillers, i.e. Ca(OH)2,... 

In the present study, the roll bonding behaviour of Al-3003/Al-4043 and Al-3003/Zn sheets were compared. The bi-layer sheets were produced by a roll bonding process at different reductions in thickness and rolling temperatures. The joint strengths of the sheets were evaluated by peel and bend testing before and after supplemental annealing treatment. The peeled surfaces were examined using a scanning electron microscope. The results indicated that the Al-3003/Al-4043 sheets were bonded with higher joint strength and lower threshold reductions in thickness with respect to the Al-3003/Zn sheets. In contrast to the Al-3003/Zn sheets, significant improvement was observed in the joint strength of... 

In this research, the welding characteristics of a new UHSLA steel, 35NiCrMoV123, have been studied in two general conditions (annealed and quench-tempered). Carbon equivalent value of 35NiCrMoV123 steel is near 0.9 which classifies it as a "very difficult to weld" steel. The effects of welding heat treatment cycle (preheat, interpass, and postheat) on metallurgical and mechanical properties of weldments have been investigated by tensile, impact toughness, and hardness tests, as well as optical microscopy observations. It has been observed that by employing high-temperature stress relief (600 °C), welding could be performed in annealed condition successfully. Also, the results indicate that... 

An approach for calculating weld efficiency from the results of a peel test has been developed for 5754-aluminum strips. The method is based on estimating the effective load-bearing area of peel test specimens. A convincing agreement between the results and the theoretical model-earlier developed by Wright et al. (Metals Technol. 5 (1978) 24)-has been found. The influence of surface expansion and rolling pressure on the weld efficiency has been studied by the new approach. © 2002 Elsevier Science B.V. All rights reserved  

TiO2 nanoparticles were synthesized by hydrothermal assisted sol-gel technique. The preparation parameters including pH value, the amount of water, titanium tetra isopropoxide content, temperature and time of hydrothermal process were investigated by Taguchi statistical experiments to determine the influence of synthesizing variables on the optimal conditions and to realize the highest degree of crystallinity or smallest crystallite size. X-ray diffraction (XRD) analysis and direct band gap energy (Eg) values, measured via diffuse reflectance spectra (DRS), proved that all the samples consist of anatase as a unique phase. Transmission electron microscopy (TEM) and specific surface area... 

In the present study, a one step hydrothermal process was employed to synthesize magnetite nanoparticles using oleic acid as surfactant agent at 140 °C. Effects of reaction time and alkalinity were studied on particles size and morphology. By changing these parameters, some monodisperse spherical nanoparticles with mean particle size between 2.71 and 13.88 nm were synthesized and characterized via TEM, XRD, VSM, TGA and FT-IR techniques. Assuming the Avrami behavior of particles formation, a kinetics equation was proposed for the transformation rate at 140 °C. Using some simplifying assumptions, nucleation and growth rates were calculated for the hydrothermal formation of magnetite...