Sharif Digital Repository

The present work describes sensing application of modified TiO 2 nanotubes having carbon-Pt nanoparticles for simultaneous detection of dopamine and uric acid. The TiO 2 nanotubes electrode was prepared using anodizing method, followed by electrodeposition of Pt nanoparticles onto the tubes. Carbon was deposited by decomposition of polyethylene glycol in a tube furnace to improve the conductivity. The C-Pt-TiO 2 nanotubes modified electrode was characterized by cyclic voltam-metry and differential pulse voltammetry methods. The modified electrode displayed high sensitivity towards the oxidation of dopamine and uric acid in a phosphate buffer solution (pH 7.00). The electro-oxidation currents... 

In this study a novel Pt/Ni nanostructure consisting of nano-bushes and nanocubes was fabricated onto TiO 2 nanotubes. The scanning electron microscopy images showed that a large amount of well-dispersed nano-architectures had uniformly covered all over the surface which made an electrode with high surface area. It was obviously seen that the nanocube structures mainly consists of Ni had been grown on top of each other while the Pt colonies represented bush-like structures. As a non-enzymatic glucose biosensor, the Pt/Ni TiO 2 nanotubes modified electrode exhibited an excellent performance. The proposed biosensor had two linear ranges for detection of glucose from 0 to 0.12 mM (correlation... 

Co/Cu multilayers were deposited in a sulfate solution by controlling the current and potential for the deposition of cobalt and copper layer respectively. The electrochemical behavior of these multilayers was studied by cyclic voltammetry and current transients. In addition, a mathematical analysis was used to characterize the electrodeposition system. Simultaneously, the nucleation and growth mechanisms were monitored by these techniques. In this case, the results clearly showed that electrodeposition of cobalt layers was a kinetically controlled process while the reduction of copper ions was a diffusion-control process. Although nucleation mechanism of the single Co deposit was found as a... 

The cobalt-nickel/copper multilayer films were prepared by electrodeposition process in sulfate solution using a three electrode cell. Cyclic voltammetry and double chronoampermetry techniques were utilized to characterize the multilayer system and to obtain the nucleation and growth mechanism. The cyclic voltammograms determined the reduction potential range of the three components and also clearly emphasized that electrodeposition of cobalt-nickel alloy was controlled by a kinetic process, while copper ions were reduced with diffusion-controlled mechanism. These results were confirmed with those which were extracted from the chronoampermetry curves. In addition, the current transients... 

A simple modified TiO2 nanotubes electrode was fabricated by electrodeposition of Pd, Pt and Au nanoparticles. The TiO2 nanotubes electrode was prepared using the anodizing method, followed by modifying Pd nanoparticles onto the tubes surface, offering a uniform conductive surface for electrodeposition of Pt and Au. The performance of the modified electrode was characterized by cyclic voltammetry and differential pulse voltammetry methods. The Au/Pt/Pd/TiO2 NTs modified electrode represented a high sensitivity towards individual detection of dopamine as well as simultaneous detection of dopamine and uric acid using 0.1 M phosphate buffer solution (pH 7.00) as the base solution. In both case,... 

Progressive conversion/shrinking core (PC-SC) models of constant-size cylinders were exploited to interpret the decarburization reactions of MgO-C-Si bricks heated up under blown air. Chemical adsorption/solid (or pore) diffusion mechanisms governed the reaction rate. With 5% silicon, chemical adsorption vanished at 1000 and 1100°C. The oxidation rate lowered then with temperature. This was due apparently to the blocking of the pore-end gorges by the voluminous compounds (like Forstrite). Arrhenius plots of the specific rates yielded the activation energies of the prevailing steps. Without Si antioxidant, three steps were appreciated having activation energies of 51.65 (for chemical... 

TiO2nanocrystals were prepared by hydrolysis and peptisation of titanium isopropoxide under different pH values. The as-prepared powder of very fine anatase crystallites ranges from 8 nm in acidic solution of pH 3 to 10 nm in basic solution of pH 8. Heat treatment of the powders leads to grain growth and anatase - rutile transformation. Experimental results have shown that the anatase to rutile phase transformation in the heat-treated powders depend not only on primary crystallite size but also the presence of brookite phase. It is observed that in the powders with the same size the presence brookite phase would accelerate the anatase to rutile transformation. Furthermore it has been found... 

Graphene oxide (GO) sheets were synthesized through a modified Hummers' method. Using high resolution transmission electron microscopy the thickness of the GO sheets in a multilayer structure of stacked GO sheets was found ∼0.8 nm. A nanosecond pulsed laser (with wavelength of 532 nm and average power of 0.3 W) was applied for effective and environment friendly reduction of the GO sheets in an ammonia solution (pH ∼9) at room temperature conditions. The deoxygenation of the GO sheets by the pulsed laser reduction method was confirmed by using UV-visible, Fourier transform infrared, X-ray photoelectron spectroscopy (XPS) and thermo gravimetric analysis. Based on XPS analysis, the O/C ratio of... 

Biphase TiO2 nanoparticles have been prepared by sol-gel method. Water/titanium molar ratio (r) has been used to control the hydrolysis and condensation of titanium isopropoxide in solution producing titanium oxide with two different polymorphs. The influence of crystallite size and morphology of prepared TiO2 on the phase transformation of the resultant materials has been investigated. Synthesized powders were characterized by X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Different trends can be observed in the phase transformation and particle growth of the prepared titanium oxide nanomaterial. It was concluded that, the rate of particle... 

Kinetics of air oxidation of MgO-C-Al refractory at 600°-1300°C were investigated using the software based on the modifled shrinking core model (KDA). Commercial bricks containing 88.5% MgO, 10% residual carbon, and 1.5% aluminum anti-oxidant were oxidized isothermally with air. Combination of experimental data with model calculations indicated gas diffusion through solid material and pores as a major controlling step. Previously observed chemisorption process was eliminated from the rate-controlling mechanism with addition of aluminum antioxidant. Comprehensive rate equations were devised for MgO-C-Al and MgO-C oxidation reactions. Overall activation energies of Q id (internal diffusion) =... 

Hydrolysis of titanium isopropoxide alcoholic solution has been used to prepare the crystallized TiO2 nanoparticles at low temperature. Concentration ratio was used to control the pathway of sol-gel process and change the physical characteristics of TiO2 nanopowders. The crystallinity, morphology and size of aged TiO2 nanopowders were studied by X-ray diffraction and Scanning Electron Microscopy (SEM). FTIR and, Thermo-Gravimetric (TG) analysis were used to identify the functional groups and thermal behavior of prepared samples. Experimental results have shown that high crystalline TiO2 nanomaterial with anatase polymorph can be obtained at room temperature. It has been found that the... 

TiO2 a nanotube array was prepared using an anodization process. The process proceeded in a two-electrode cell containing of platinum sheet as the cathode electrode. Two phosphate-base electrolyte solutions containing different amounts of HF and NH4F were prepared. Different concentration of fluorine ions were examined in respected electrolytes. Current transient techniques were used to produce the TiO2 nanotubes at constant voltage of 18-25V. It was revealed that anodization at 18-22V, in so-called electrolytes would end up to nano-tubular structure. However the tubular structure prepared at 20V and from phosphate electrolyte containing of 0.5 wt% NH4F as well as 0.5 wt% HF, was recognized...