Sharif Digital Repository

Hydroxyapatite (HAp) nanostrips were rapidly obtained during a mild microwave heating method. Applying microwave irradiation to Ca(NO3)2·4H2O/CTAB/Na2HPO4 precursor solution, the HAp precipitation process was occurred directly and without common crystallographic transformations including dissolution and slow recrystallization. The cationic surfactant CTAB was used as a soft template to modify nucleation and growth process. TEM investigations showed that the fabricated nanostrips had a width and length of about 10 and 55 nm, respectively. The X-ray diffraction pattern revealed that the fabricated well-crystallized and high purity hydroxyapatite nanostrips had a pattern similar to the bone... 

Lanthanum hydroxide (La(OH)3) nanostructures, including elliptical nanoparticles, octahedral rods and irregular nanoparticles were prepared chemically in NaOH and KOH solutions with 10 M concentration. The obtained powders were characterized with XRD, SEM, TEM and DTA. Crystallinities, morphologies and thermal behavior of the obtained nanostructure powders were investigated under the influence of above mentioned solvents. The effect of chemical's temperature was also determined in one of the solvents (i.e. NaOH). The formation of growth in nanostructure mechanism under the influence of alkali solutions (i.e., KOH and NaOH) have been discussed considerably in this paper  

Rosette-like boehmite nanostructures were prepared successfully via a simple hydrothermal process. The obtained material was characterized with X-ray powder diffractometry (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Using Scherrer formula, the average crystallite size of the obtained boehmite rosettes was measured to be about 8 nm. It was shown that boehmite nanopetals with average width of about 41 nm determined by TEM, were formed during the hydrothermal process and then self assembled due to weak hydrogen bonds to fabricate boehmite rosettes. The specific surface area of the obtained rosette-like nanostructures was calculated through BET... 

Alkoxides are the most common precursors used for the production of alumina nanopowders. These materials are, however, expensive and corrosive. This paper introduces a new method for the production of alumina nanopowders by rapid cooling of a synthetic caustic sodium aluminate solution (Bayer liquor), followed by calcination in the presence of a surface-stabilizing agent like 1,2-dihydroxy-3,5-benzene disulfonic acid disodium salt (Tiron). The powders produced are characterized by differential thermal analysis, XRD, transmission electron microscopy, scanning electron microscope, and Brunauer-Emmet-Teller. A nanopowder of α-alumina with an average crystallite size of 27.7 nm and an average... 

Server workloads operate on large volumes of data. As a result, processors executing these workloads encounter frequent L1-D misses. In a many-core processor, an L1-D miss causes a request packet to be sent to an LLC slice and a response packet to be sent back to the L1-D, which results in high overhead. While prior work targeted response packets, this work focuses on accelerating the request packets. Unlike aggressive OoO cores, simpler cores used in many-core processors cannot hide the latency of L1-D request packets. We observe that LLC slices that serve L1-D misses are strongly temporally correlated. Taking advantage of this observation, we design a simple and accurate predictor. Upon... 

Three-dimensional (3D) bundles of self-assembled lanthanum hydroxide nanorods with average crystallite size of about 20 nm were fabricated via a facile and rapid microwave-assisted chemical route. The obtained material was characterized with X-ray diffractometry (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) investigations. The obtained nanorods have average diameter of about 115 nm and average length of about 730 nm. Self-assembly of primary La(OH)3 nanoparticles and their subsequent anisotropic growth along 〈2 0 0〉 direction, was proposed to be the mechanism for the formation of 3D bundles of nanorods, using TEM images. The thermal behavior of the... 

Using multiple antennas at the transmit and receive sides of a passive radar brings both the benefits of MIMO radar and passive radar. However one of the obstacles arisen in such configuration is the receive antennas placement in proper positions so that the radar performance is improved. Here we just consider the case of positioning one receiver among multiple illuminators of opportunity. Indeed it is a start for the solution of optimizing the geometry of the multiple receivers in a passive radar  

SbCl3 supported on montmorillonite K-10 is an efficient catalyst for the ring opening of epoxides with aromatic amines under solvent-free conditions and microwave irradiation to give the corresponding b-amino alcohols in high yields with high regioselectivity  

In this paper, we consider an integrated sensing and communication (ISAC) system with wireless power transfer (WPT) where an unmanned aerial vehicle (UAV)-based radar serves a group of energy-limited communication users in addition to its sensing functionality. In this architecture, the radar senses the environment in phase 1 (namely sensing phase) and mean-while, the communications users (nodes) harvest and store the energy from the radar transmit signal. The stored energy is then used for information transmission from the nodes to UAV in phase 2, i.e., uplink phase. Performance of the radar system depends on the transmit signal as well as the receive filter; the energy of the transmit... 

One of the important obstacles in MIMO (Multiple Input Multiple Output) radars is the issue of designing proper transmit signals. Indeed, the capability of signal design is a significant advantage in MIMO radars, through which, the system can achieve much better performance. Many different aspects of this performance improvement have been considered yet, and the transmit signals have been designed to attain such goal, e.g., getting higher SNR or better detector's performance at the receiver. However, an important tool for evaluating the radar's performance is its ambiguity function. In this paper, we consider the problem of transmit signal design, in order to optimize the ambiguity function... 

Two gains play key roles in recently developed MIMO wireless communication systems: "spatial diversity" gain and "spatial multiplexing" gain. The diversity gain refers to the capability to decrease the error rate of the MIMO channel, while the multiplexing gain implicitly refers to the amount of increase in the capacity of the MIMO channel. It has been shown that there is a fundamental tradeoff between these two types of gains, meaning interplay between increasing reliability (via an increase in the diversity gain) and increasing data rate (via an increase in the multiplexing gain). On the other hand, recently, MIMO radars have attracted much attention for their superior ability to enhance... 

It is a well known fact that using multiple antennas at transmit and receive sides improves the detection performance. However, in such multiple-input multiple-output (MIMO) configuration, proper positioning of transmitters and receivers is a big challenge that can have significant influence on the performance of the overall system. In addition, determining the power of each transmitter under a total power constraint is a problem that should be solved in order to enhance the performance and coverage of such a system. In this paper, we design the Neyman-Pearson detector under the Rayleigh scatter model and use it to introduce a criterion for the antenna placement at both transmit and receive... 

There has been much interest, recently, towards exploiting the Multiple-Input Multiple-Output (MIMO) technique in radar. It is shown that using multiple antennas at transmit and receive sides can improve the performance of the system. However, in order to analyze the system's performance, its ambiguity function, i.e. the ambiguity function of a MIMO radar, is needed to be defined. In this paper, beginning from the information theoretic definitions, we derive such function, specifically for a MIMO radar with widely separated antennas  

By combining the two ideas of MIMO (Multiple Input Multiple Output) and PCL (Passive Coherent Location) in radar, one can achieve the advantages of both recently developed techniques simultaneously. While using multiple antennas at the receive side provides a spatial diversity of the object to be detected, using multiple illuminators of opportunity, most importantly, makes the radar covert to the interceptors. One obstacle in such MIMO configuration is choosing the positions of the receive antennas. In this paper, after analyzing the Neyman-Pearson detector for the DVB-T based PCL, we introduce the probability of missed detection as a criterion to place the receive antenna. Here, we only... 

One of the most important obstacles in passive radar applications is removing the direct signal from the target channel. Otherwise, week echoes from the targets in the target channel would be ignored due to the limited dynamic range of the system. One of the most effective techniques in this field is using adaptive filters. In this paper various adaptive filters are introduced and their performances are shown and compared  

It has been shown that using multiple antennas in a radar system improves the performance considerably, since multiple target echoes are received from different aspect angles of the target. In this way, the target detection is improved. However, when using multiple antennas, some problems, such as designing the transmit signals, synchronization, etc. emerge that should be solved. One of such problems is the receiver placement. Receiver placement deals with choosing a proper position for the receive antenna in order to optimize the whole system's performance. In this paper, a receiver placement procedure based on improving the radar ambiguity function is proposed for the case of a multisite... 

By employing the MIMO (multiple-input-multiple-output) technology in radar, some new problems emerged, that, in order to benefit the MIMO gains in radar, it was necessary to solve them suitably. One of such obstacles is determining the positions of receive antennas in a MIMO radar system with widely separated antennas (WS MIMO radar), since it is shown that the antennas' positions affect the whole system's performance considerably. In this study, a proper receivers' positioning procedure is proposed. To do this end, four criteria are developed based on the proposed MIMO detector and the MIMO ambiguity function. The simulations verify that the proposed positioning procedure improves the... 

Phenols and alcohols are silylated with hexamethyldisilazane (HMDS) under microwave irradiation in solvent-free condition in good to excellent yields