Sharif Digital Repository

Copper matrix composites have received more attentions as possible candidate for thermal and electrical conductive materials to be used in electrical contact applications. In this study, five-layered Cu/YSZ (yttria-stabilized zirconia) functionally graded material (FGM) and copper matrix composite specimens containing 3 and 5 vol% YSZ particles plus pure Cu specimen were synthesized using powder metallurgy (PM) route and spark plasma sintering (SPS) consolidation process. The microstructural and some physical, mechanical features of all specimens were characterized. Microscopic examinations showed that ultrafine YSZ particles were distributed in the copper matrix almost homogeneously. An... 

In the present study, yttria stabilized zirconia (YSZ) reinforced Cu matrix composite specimens were produced by spark plasma sintering (SPS). For comparison, pure Cu specimen was also produced in the same conditions. The effect of particles content on microstructure, relative density, electrical conductivity, and Vickers hardness was evaluated. The pin-on-disk test was also performed to determine dry sliding wear behavior of specimens under different wear conditions. After sliding wear tests, the worn surfaces were examined by field emission scanning electron microscopy (FE-SEM). Microstructural study showed satisfactory distribution of reinforcement particles in copper matrix. The relative... 

Water shielding phenomenon generally occurs after waterflooding in water-wet rocks, and impedes direct contact between the oil and the injected gas in tertiary gas injection processes. In this work, a set of visualization experiments were performed on micromodel patterns including designed dead-end pores with a film of water on the surface of pore bodies, which is a more realistic representation of porous media. The experiments were conducted at different miscibility conditions, and the required time for water to be displaced from the throat by the swelling of oil was measured for first contact miscible (n-C5/CO2) and immiscible (n-C10/CO2) systems. In the next step, a model was proposed to... 

We have used the Maxwell-Stefan diffusion theory to model the mass transfer between tertiary-injected gas and residual oil blocked by water, in order to predict the time required for the rupture of the water barrier due to oil swelling. We have also designed and conducted a set of visualization micromodel experiments on various pure and multicomponent oil-gas systems to measure the water rupture time in tertiary gas injection processes. The experimental results show that the initial pressure and dimensions of the system, the oil and gas composition, and the gas solubility in water control the oil swelling process. The experimentally measured rupture times are then employed to evaluate the... 

Water shielding happens in water-wet reservoirs after waterflooding, where water fills the throats of oil-bearing dead-end pores and prevents tertiary injected gas from direct contact with oil; however, diffusion takes place between gas and oil via dissolution of components in water, which causes the oil to gradually swell until it completely pushes away the water from the throat. None of the previous experimental and numerical studies on the water-shielded oil recovery from a single dead-end pore have considered the presence of the thin water film on the surface of water-wet rocks, whereas it considerably enhances the gas-oil mass transfer rate by extending the contact area between the oil... 

The insect circulatory system contains an open hemocoel, in which the mechanism of hemolymph flow control is ambiguous. As a continuous fluidic structure, this cavity should exhibit pressure changes that propagate quickly. Narrow-waisted insects create sustained pressure differences across segments, but their constricted waist provides an evident mechanism for compartmentalization. Insects with no obvious constrictions between segments may be capable of functionally compartmentalizing the body, which could explain complex hemolymph flows. Here, we test the hypothesis of functional compartmentalization by measuring pressures in a beetle and recording abdominal movements. We found that the... 

In [1], [2] it is shown that the minimum broadcast rate of a linear index code over a finite field Fq is equal to an algebraic invariant of the underlying digraph, called minrankq. In [3], it is proved that for F2 and any positive integer k, minrankq(G) ≤ k if and only if there exists a homomorphism from the complement of the graph G to the complement of a particular undirected graph family called 'graph family {Gk}'. As observed in [2], by combining these two results one can relate the linear index coding problem of undirected graphs to the graph homomorphism problem. In [4], a direct connection between linear index coding problem and graph homomorphism problem is introduced. In contrast to... 

I present an in-depth review of the trends and the directions taken by researchers worldwide in optical code-division multiple-access (OCDMA) systems. I highlight those trends and features that I believe are essential to the successful introduction of various OCDMA techniques in communication systems and data networks in the near future. In particular I begin by giving a comprehensive review of the construction of optical orthogonal codes (OOCs). Specifically I discuss the recently developed algorithms that are based on matrix algebra, which simplify and enhance the efficiencies of algorithms in OOC generation. In communication systems studies I first focus on and discuss various OCDMA... 

In this paper, we analyze the worst-case delay performance of a network of fair queuing servers in case of multiple-paths between source-destination pairs. In order to develop worst-case delay analysis for the multiple-path scenario, two challenging events should be addressed: merging different sub-streams of a session as well as distributing a traffic stream among different paths (traffic partitioning). Specifically, we propose to merge incoming sub-streams of a session to a node according to a limited rate Fair Queuing (FQ) scheme. Although the merged stream is treated as a unity, this approach results in a guaranteed level of service to each sub-stream. In addition, an algorithm is... 

This paper presents an investigation of the effects of tool rake angle and nose radius on the surface quality of ultraprecision diamond-turned porous silicon. The results showed that as rake angle decreases, the high-stress field induced by the tool edge increases, causing microcracks to propagate extensively near the pore walls. As a result, the ductile-machined areas shrank under a negative tool rake angle. On the other hand, brittle fracture occurred around pores released cutting pressure significantly. These trends of rake angle effects are distinctly different from those in the cutting of non-porous silicon. Finite element simulation of stress in the cutting area agreed with the... 

This paper presents an investigation of the effects of tool rake angle and nose radius on the surface quality of ultraprecision diamond-turned porous silicon. The results showed that as rake angle decreases, the high-stress field induced by the tool edge increases, causing microcracks to propagate extensively near the pore walls. As a result, the ductile-machined areas shrank under a negative tool rake angle. On the other hand, brittle fracture occurred around pores released cutting pressure significantly. These trends of rake angle effects are distinctly different from those in the cutting of non-porous silicon. Finite element simulation of stress in the cutting area agreed with the... 

The mechanical properties of Mg-4wt.% Zn alloy single crystals along the [0001] orientation were measured through micropillar compression at 23 °C and 100 °C. Basal slip was dominant in the solution treated alloy, while pyramidal slip occurred in the precipitation hardened alloy. Pyramidal dislocations pass the precipitates by forming Orowan loops, leading to homogeneous deformation and to a strong hardening. The predictions of the yield stress based on the Orowan model were in reasonable agreement with the experimental data. The presence of rod-shape precipitates perpendicular to the basal plane leads to a strong reduction in the plastic anisotropy of Mg. © 2020 Elsevier B.V  

The mechanical properties of Mg-4wt.% Zn alloy single crystals along the [0001] orientation were measured through micropillar compression at 23 °C and 100 °C. Basal slip was dominant in the solution treated alloy, while pyramidal slip occurred in the precipitation hardened alloy. Pyramidal dislocations pass the precipitates by forming Orowan loops, leading to homogeneous deformation and to a strong hardening. The predictions of the yield stress based on the Orowan model were in reasonable agreement with the experimental data. The presence of rod-shape precipitates perpendicular to the basal plane leads to a strong reduction in the plastic anisotropy of Mg. © 2020 Elsevier B.V  

This research explored the influences of shielding gases on the appearance of weld beads and the microstructures and mechanical properties of thin-wall samples using conventional gas metal arc welding as the heat source by using 5356 aluminium alloy welding wire as the raw materials and nitrogen (N2) and argon (Ar) as the shielding gases. The results showed that under the same parameters and after mono-layer single-bead welding was performed using N2 as the shielding gas, the bead height was higher, the bead width was narrower, and the penetration depth was shallower. The grain size of the thin-wall sample protected by N2 was 43.5–47.8 % smaller than that obtained under Ar protection.... 

In this paper, we describe a carbon dioxide mineralization process and its associated solid products. These solid products include amorphous silica, iron hydroxides and magnesium carbonates. These products were subjected to various characterization tests, and the results are published here. It was found that the iron hydroxides from this process can have different crystalline properties, and their formation depended very much on the pH of the reaction conditions. Different forms of magnesium carbonate were also obtained, and the type of carbonate precipitated was found to be dependent on the carbonation temperature. Hydromagnesite was obtained mainly at low temperatures, while dypingite was... 

Employing a proper pulse shaper in the conventional split Hopkinson pressure bar (SHPB) test helps to achieve dynamic equilibrium condition and to fulfill a constant strain rate condition in the test specimen. To this end, the parameters affecting the incident pulse shape, i.e., pulse shaper thickness, pulse shaper diameter, striker bar length and striker bar velocity are experimentally studied. Moreover, simulation results, validated by experimental data together with wave propagation analysis, are exploited to provide general guidelines to properly design a pulse shaper. It is recommended to use a relatively large diameter pulse shaper for testing work-hardening materials. Also, for... 

In this work the effects of backwash pressure, duration of acid and sodium hydroxide backwashing, sodium hydroxide concentration, and the duration of forward washing on performance of permeate flux recovery (PFR) were investigated. A two-level fractional factorial design (FFD) was used to design the experiments. The ability of back propagation neural network (BPNN) and radial basis function neural network (RBFNN) in predicting the performance of cleaning-in-place (CIP) of hydrophilic polyethersulfone (PES) membrane were investigated. It is found that BPNN has better ability in predicting the PFR performance than RBFNN. The best architecture of BPNN was a network consisting of 1 hidden layer... 

Distant, dusty and extremely luminous galaxies form a key component of the high redshift universe, tracing the period of intense cosmic activity that ultimately gave rise to the present-day universe. These highly luminous galaxies, first detected in the ground-based submillimeter region, are however optically very faint, which hampers identification of the optical counterpart and the measurement of a redshift. We are developing a new direct-detection submm spectrograph DESHIMA. By taking advantage of the rapidly advancing technology of superconducting microresonators, DESHIMA will revolutionize the appearance and capabilities of a submm spectrograph. There will no longer be large grating...