Sharif Digital Repository

This paper proposes a new experimental procedure for magnetic characterization of switched reluctance machines. In the existing methods, phase voltage and current data are captured and further processed to find the flux linkage. Conventionally, assuming zero initial flux value, the flux linkage can be found by integrating the corresponding voltage term. However, the initial flux value is usually unknown, e.g., it can be nonzero when the current is zero due to the residual flux effect, and, thus, imposes error in magnetic characterization. The proposed method addresses this issue by considering an additional equation in steady state. This method injects a low-frequency sinusoidal current to... 

This is the first research on the vibration and buckling analysis of a graphene nanoplatelet composite (GPLRC) microdisk in the framework of a numerical based generalized differential quadrature method (GDQM). The stresses and strains are obtained using the higher-order shear deformable theory (HOSDT). Rule of the mixture is employed to obtain varying mass density, thermal expansion, and Poisson's ratio, while the module of elasticity is computed by modified Halpin-Tsai model. Governing equations and boundary conditions of the GPLRC microdisk are obtained by implementing Extended Hamilton's principle. The results show that outer to inner ratios of the radius (Ro/Ri), ratios of length scale... 

Tailored welded blanks (TWBs) technology can give the important possibilities to obtain components in the automobile industry. Friction stir welding (FSW) is a joining approach, which can adhere parts well with desired properties in weld zone. In this article, the main aim is investigation the effect of weld zone orientation on forming limit diagram (FLD) of the TWBs using experimental and finite element model. Three TWBs are produced FSW with three different orientations of weld zones including 00, 450 and 900 against major stress direction. The microstructure of the weld zones is divided and then observed via metallography procedures. Tensile tests are carried out to determine the... 

In this article, thermal buckling and frequency analysis of a size-dependent laminated composite cylindrical nanoshell in thermal environment using nonlocal strain–stress gradient theory are presented. The thermodynamic equations of the laminated cylindrical nanoshell are based on first-order shear deformation theory, and generalized differential quadrature element method is implemented to solve these equations and obtain natural frequency and critical temperature of the presented model. The results show that by considering C–F boundary conditions and every even layers’ number, in lower value of length scale parameter, by increasing the length scale parameter, the frequency of the structure... 

In this article, thermal buckling and frequency analysis of a size-dependent laminated composite cylindrical nanoshell in thermal environment using nonlocal strain–stress gradient theory are presented. The thermodynamic equations of the laminated cylindrical nanoshell are based on first-order shear deformation theory, and generalized differential quadrature element method is implemented to solve these equations and obtain natural frequency and critical temperature of the presented model. The results show that by considering C–F boundary conditions and every even layers’ number, in lower value of length scale parameter, by increasing the length scale parameter, the frequency of the structure... 

This is the first research on the frequency analysis of a graphene nanoplatelet composite circular microplate in the framework of a numerical-based generalized differential quadrature method. Stresses and strains are obtained using the higher order shear deformation theory. The microstructure is surrounded by a viscoelastic foundation. Rule of the mixture is used to obtain varying mass density and Poisson’s ratio, whereas the module of elasticity is computed by a modified Halpin–Tsai model. Governing equations and boundary conditions of the graphene nanoplatelet composite circular microplate are obtained by implementing Hamilton’s principle. The results show that outer to inner radius ratio... 

This is the first research on the frequency analysis of a graphene nanoplatelet composite circular microplate in the framework of a numerical-based generalized differential quadrature method. Stresses and strains are obtained using the higher order shear deformation theory. The microstructure is surrounded by a viscoelastic foundation. Rule of the mixture is used to obtain varying mass density and Poisson’s ratio, whereas the module of elasticity is computed by a modified Halpin–Tsai model. Governing equations and boundary conditions of the graphene nanoplatelet composite circular microplate are obtained by implementing Hamilton’s principle. The results show that outer to inner radius ratio... 

A Cúk converter operating in discontinuous capacitor voltage mode (DCVM) is an inherent power factor correction converter. A reduced-order switch-network model of a Cúk converter in DCVM is developed, which is valid for both dc-dc and ac-dc applications. The model can be used for controller analysis and design. Moreover, a fast dynamic response controller is proposed, which is an integration of a switching-frequency control unit and a proportional-integral (PI) controller. The PI controller is in charge of duty ratio adjustment. In the proposed controller, unlike conventional PI controllers, switching frequency is no longer fixed and varies as load changes. The switching-frequency control... 

Cúk Converter operating in discontinuous capacitor voltage mode is an inherent PFC converter in which, unity power factor can be achieved using constant duty cycle and switching frequency. In this paper, a reduced-order switch network modeling technique is applied to Cúk converter operating in DCVM in order to derive small-signal model of the converter assuming a dc voltage source as the input source of the converter. This model is extended to derive the small-signal behavior of the converter while operating as a PFC converter. The validity of the proposed model is confirmed by both simulation and experimental results. Afterwards, a new control strategy is proposed in which switching... 

This is the first research on the thermal buckling analysis of graphene nanoplatelets reinforced composite (GPLRC) doubly curved open cylindrical micropanel in the framework of numerical-based two-dimensional generalized differential quadrature method (2D-GDQM). Additionally, the small-scale effects are analyzed based on nonlocal strain gradient theory (NSGT). The stresses and strains are obtained using the high-order shear deformable theory (HOSDT). The rule of mixture is employed to obtain varying thermal expansion, and Poisson's ratio, while module of elasticity is computed by modified Halpin-Tsai model. In addition, nonlinear temperature changes along the GPLRC micropanel's thickness... 

Due to the rapid development of process manufacturing, composite materials with graphene-reinforcement have obtained commercially notices in promoted engineering applications. For this regard, vibrational characteristics of a cylindrical nanoshell reinforced by graphene nanoplatelets (GPL) and coupled with piezoelectric actuator (PIAC) is investigated. Also, the nanostructure is embedded in a viscoelastic medium. The material properties of piece-wise graphene-reinforced composite (GPLRC) are assumed to be graded in the thickness direction of a cylindrical nanoshell and estimated through a nanomechanical model. For the first time in the current study is considering the effects of... 

Local educational institutions produce in-house English for Specific Purpose (ESP) materials according to the curriculum policies designated and developed by the Ministry of Higher Education In Iran. To this end, this book aims to be used in the Iranian setting at the tertiary level for undergraduate students majoring in Mechanical Engineering. Moreover, the style of English usage in this ESP textbook is American.
Regarding the content of the textbook, it has both thematic organizations in which the topics are relevant and includes sufficient treatment of the target language areas necessary for the students. The principle organizing approach of this textbook is theme-based. In addition,... 

The aim of this study is to employ feedback control loops to provide a stable forward dynamics simulation of human movement under repeated position constraint conditions in the environment, particularly during stair climbing. A ten-degrees-of-freedom skeletal model containing 18 Hill-type musculotendon actuators per leg was employed to simulate the model in the sagittal plane. The postural tracking and obstacle avoidance were provided by the proportional—integral—derivative controller according to the modulation of the time rate change of the joint kinematics. The stability of the model was maintained by controlling the velocity of the body's centre of mass according to the desired centre of...