Sharif Digital Repository

Low frequency (LF) O2 plasma was used to modify the surface of polysulfone (PSF) gas separation membranes. The effect of treatment time and plasma power input on the membranes was also investigated. Pure CO2 and CH4 gas permeation measurements were performed before and after plasma treatment. The results showed the increase of permeability of the treated membranes due to surface ablation and surface polarization. However, the CO2/CH4 permselectivity of the treated membranes varied from 7.7 to 45.3 depending on the treatment conditions. Attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy determined the introduction of oxygen containing polar groups on the surface... 

In spite of the fact that failures in distribution systems constitute a high percentage of customer’s interruptions, they have received less attention than generation and transmission systems at least in the amount of academic and industrial publications in the past decades. However as the business turns its attention to customers from consumers, focuses are moving toward power distribution systems in recent years. Its main problem that makes this high percentage of contribution in customer’s interruption is their widespread applications through all the places that there is a civilization. Contribution of many components in the system leads to high failure rate and because they spread every... 

In this study, thermo-mechanical behavior of an austenitic stainless steel AISI316L was investigated using mathematical modeling and experimental analysis during warm rolling process. First, the thermo-mechanical analysis was carried out employing the finite element software, Abaqus CAE, to assess temperature, strain, velocity and stress distribution during rolling. Then, rolling operations on 316L austenitic steel were performed under different working conditions while mechanical testing as well as microstructural observations were made on the rolled steels. Using simulation results and practical data, microstructural events and mechanical properties after warm rolling of stainless steel... 

In this research, the hot and warm rolling of stainless steel 304 was studied. First the rolling process was simulated using Finite Element Method software ABAQUS and the distribution of temperature and strain in the process under discontinuous conditions were predicted. Next, hot and warm rolling of stainless steel 304 under different conditions was carried out. Specimens were cut and subject to mechanical testing, metallography and electron microscopic studies. Data obtained from these experiments and the predicted trends from ABAQUS were compared, therefore studying the effect of different parameters on the microstructure and mechanical properties of the rolled specimen. Results indicate... 

A mathematical model was developed to assess thermomechanical behavior of work rolls during warm rolling processes of AA2017. A combined finite element analysis-slab method was first developed to determine thermal and mechanical responses of the strip being rolled under steady-state conditions; Then, the calculated roll pressure and temperature field were utilized as the governing boundary conditions for the thermomechanical problem of the work roll. Finally, the thermomechanical stresses within the work rolls were predicted by a thermoelastic finite element approach. The results indicate that, in warm strip rolling, thermal and mechanical stresses developed in the work rolls are comparable.... 

In this research, temperature distribution and roll force during steady state warm and hot rolling of 6061 Al alloy strip have been simulated, using finite element method and upper bound solution. At first, the velocity field and deformation zone shape have been determined, by means of upper bound solution, then using 2D finite element method, the temperature distribution within rolling and considering rate of heat of deformation, has been calculated. This model generalized for two pass steady state warm and hot rolling. Also, in order to evaluate the predictions, the experimental recorded of temperature variation, during hot rolling and temperature variation predicted by model has been... 

In this study, transformation of austenite to ferrite under continuous cooling condition of a low carbon steel was investigated. In the first step, a heat transfer model was employedconsidering governing heat transfer boundary conditions and a microstructure model based on Cellular Automaton method was used simultaneouslyto predict austenite to ferrite transformation progress. The influence of pre-heating temperature and primary austenite grain size on the final ferrite grain size and distribution were perdected. To verify the simulation results, experimental processes were utilized. The microstructure distribution was determined by means of Clemex Pro software then, these results were... 

Austenite in the 300 stainless steels is not a table phase in deformation processing during which martensite phase forms. This causes significant changes in the microstructures as well as the mechanical properties of deformed steel. In this work, the effects of rolling speed, reduction, temperature and strain pass on the strain-induced martensite during strip rolling operation of stainless steel 304L are studied. Cold rolling experiments under different speeds, reduction and temperature are conducted and then, the microstructural events and mechanical properties of the rolled steel are evaluated. For doing so, different testing techniques including tensile test, hardness measurement, optical... 

In this work, annealing procedure of cold-deformed AA5052-SiC composite has been simulated by using cellular automata approach and the effect of SiC second phase on softening kinetics has been studied. To do so, site saturated nucleation has been employed to establish initial microstructure. In addition, topological changing due to deformation has been implemented on the microstructure. During annealing, recovery and recrystallization phenomena occur simultaneously, and it has strong effect on the annealed microstructure. Therefore, during annealing, recrystallization and recovery has been considered simultaneously and decreasing in the stored energy, which has developed during deformation... 

A mathematical model has been proposed to estimate the deformation pattern and the required power in cold plate rolling using the stream function method and upper bound theorem. In the first place admissible velocity distributions as well as the geometry of deformation zone were derived from the proposed stream functions. Then, the optimum velocity field was obtained by minimization of the power function computed based on the upper bound theorem. Then a steady state heat transfer equation has been solved in whole model using finite element method. In order to verify the predictions, rolling experiments on aluminum plates were conducted and also, a finite element analysis performed employing... 

Static recrystllization in low carbon steel after two type of deformation –sidepress as an inhomogeneous deformation and rolling as a common industrial process - has been simulated using Cellular Automata (CA). The finite element method was utilized to compute the strain and stored energy distribution due to deformation. The initial microstructures were created by simulation of recrystallization with homogeneous site-saturated nucleation and topologic deformation was also considered in model. Subsequently using the result of FEM, stored energy of deformation was calculated and transferred into a two dimensional CA lattice. Nucleation rate and grain boundary velocity were considered... 

Mechanical behavior of aluminum-magnesium alloy, AA5083, was studied at high temperatures using hot tensile testing together with uniaxial creep experiments. In the first place, the as-received AA5083 sheet was subjected to annealing heat treatment to remove the effect previous plastic straining. Then, creep experiments were conducted at temperatures in the range of 190°C to 300 ° C under constant the stress varied between 30 MPa to 100 MPa. The hot tensile testing was also carried out from room temperatures up to 400 °C under nominal constant strain rates of 0.0005, 0.005, 0.01 and, 0.05 (1/s). In addition to the mechanical testing, optical metallography and scanning electron microcopy were...