Sharif Digital Repository

The behaviour of a semi-rigid connection with appreciable shear deformation capacity was studied experimentally. The tests carried out on the specimens of this connection composed of ‘monotonic’ and ‘cyclic’ tests. The monotonic tests results showed the high shear deformation capacity of this connection as well as its high energy dissipation capacity. The cyclic tests, however, indicated the ability of this connection to endure large number of ‘well-rounded’ hysteresis cycles, which led to the dissipation of great amount of energy before failure  

High purity titanium nanoparticles were synthesized by utilizing Electromagnetic Levitation Melting Gas Condensation (ELM-GC) method. High purity titanium samples were melted by electromagnetic levitation to a temperature of 1700 ± 20 °C in a silica tube. High purity argon and helium were employed as carrier gases and cooling agent. Particlesize, morphology, and Purity of the produced nanoparticles were studied by Field-Emission Scanning Electron Microscopy (FE-SEM), X-ray Diffraction (XRD), Dynamic Light Scattering (DLS), X-ray fluorescence (XRF), and ICP-AES analysis. The FE-SEM, DLS and XRF studies confirmed narrow size distribution of almost spherical shape pure titanium nanoparticles... 

When a crack is subjected to a compression field, it will close and its edges will get into contact with each other. Depending on the direction and magnitude of the loads and also the coefficient of friction, ‘stick’ or ‘slip’ situationsbetween the edges will occur. This type of crack is known as ‘frictional crack.’ In this project, first these cracks are studied analytically and the order of singularity is derived using asymptotic analysis and also the analytical fields are determined for both ‘isotropic’ and ‘orthotropic’ materials. Then, numerical simulations are carried out using extended finite element method which is considered as the most powerful means for analyzing the problems... 

Currently, drilling such as vertical or straight-hole drilling, i.e. usually less than 30 degrees inclined, or deflection drilling is used to drill at conventional and even unconventional reservoirs around the world to increase recovery factor and productivity. A major challenge is cleaning the hole or removing debris which if not done properly can lead to problems such as stuck pipes. In addition, Improper use of drilling fluid in terms of rheological properties in different stages of drilling operations can cause the well to collapse due to the accumulation of particles in the annular space. The transfer speed of particles is very important in cleaning the well. Inefficient cleaning of... 

Due to unusual response of structures of buildings with irregularity in their architecture to dynamic excitations, to have a comprehensive knowledge of their behavior during earthquakes is of utmost importance. Building irregularities are in general divided into two major categories, namely Irregularity in Plane and Irregularity in Elevation, and one of the forms of the latter is where there is a split in the levels of the building. In this work, through a series of case studies, the effects of P- phenomenon on the behavior of steel split-level building structures were studied. 5, 10 and 15 story buildings with 5 and 6 bays, and level splitting of 30, 60, 90, 120 and 150 cm were studied. All... 

Mesoscopic hydrodynamic equations are solved employing a VOF based method to investigate the equilibrium shape of nanodroplets positioned over various topographic geometries of the supporting substrate for three-dimensional systems. By taking into account liquid-liquid and liquid-solid interactions a complex distribution for inter-molecular forces over the substrates (the disjoining pressure) is observed. In this research we show that motion of nanodroplets not only caused by contact angle difference in drplets two sides, but also depend on disjoining pressure parameters.Geometries with increasing complexities, from wedges to three dimensional edges and wedges, were explored with the main... 

Observations made after previous earthquakes have shown the crucial role of irregularities in initiating damage in buildings with irregularity, either in Plan or in Elevation. Since in existing Building Codes, there is no provision for the distribution of the Equivalent Static Loads for such buildings, designers have no option but to resort to Dynamic Analysis. In this work, the seismic behaviour of a group of two-dimensional steel building structures with irregularity in elevation, namely Split-Level buildings, was studied. The studied structures consist of a series of 5- and 15-storey frames having two parts with splitting distance of 150 cm. Both, moment-resisting and braced frames were... 

With the road transportation vehicles being widely used, concerns have been increased regarding their unwanted effects. Air pollution, climate change, and oil supply security are among these effects. Many alternative fuels and propulsion systems have been proposed to be used instead of conventional ICE vehicles in recent decades. This project intends to conduct a Techno-Economic comparison between different vehicle powertrains so as to select the suitable choice to substitute conventional ICE vehicles. The vehicle options are ICE vehicles using both gasoline and CNG as fuels, Hybrid Electric Vehicles (HEVs), Plug-in Hybrid Electric Vehicles (PHEVs), and Electric Vehicles (EVs). The amount of... 

Base plates as the connecting components of steel structures to their foundations, have a crucial role in the behavior of these structures. In order to limit the thickness of base plates hence their cost within reasonable values, various types of attachments (stiffeners) are normally added to them. In this project 6 different configurations, Models, for the base plate and its attachments were considered and studied through finite element analysis. Each Model was studied under the combination of biaxial moments and a range of compressive loads including 0, 0.05 P/Py, 0.10 P/Py and 0.15 P/Py, where Py is the plastic load of the column. The moment-rotation curves of all models under various... 

Reducing air pollutant emissions from vehicles is a difficult and time consuming procedure which needs utilizing of modern emission control equipment and setting strict regulations for car factories and drivers as well. How efficient these policies are and proposing operative solutions for air quality improvement depend on developing a sustainable model which is used in vehicle emission predictions and their share in total emissions. Emission factors are not constant values as they can be affected by various operational and ambient parameters. Development of Emission inventories calls for a huge number of measurements using different vehicles in diverse conditions. Thus, recognition of... 

The city of Tehran is dealing with air pollution problems for years. Providing a solution for this problem requires information about different pollutants emission sources. In this subjects, emission factors and emission models are essential tools for decision makers. Among different mobile emission sources in Tehran, motorcycles are of high importance. In this project, for the first time in Iran, exhaust gas pollutants emission of 66 motorcycles with different ages and engine displacement volumes were measured according to Euro-3 standard certification procedure. Measurement results showed that none of the tested motorcycles passed the Euro-3 certification limit on CO emission. Calculations... 

Homogeneous Charge Compression Ignition (HCCI) engines are the new generation of internal combustion engines which have diesel-like thermal efficiency, while they have low nitrogen oxide and soot emission. One of the major problems of HCCI engines is combustion timing control due to its dependence on reactivity of the charge and chemical kinetics. Moreover, limiting operation range between knock and misfiring is the other drawback of using these kind of engines. In the present work, partially homogeneous HCCI combustion in a single cylinder diesel engine is modeled using Computational Fluid Dynamics (CFD) coupled with chemical kinetics. Simulation includes the engine cycle from exhaust valve... 

Today air pollution has become one of the major urban management concerns. Air pollution could have dangerous effects on human health in short time or long time in many situations. Numerical modelling is one of the most applicable among different ways for predicting pollutant concentration like field measurement, physical model in wind tunnel, and simulation. Modelling of pollutant dispersion is a way for estimating concentration and aggregation of the pollutant near the surface and with different distances from pollution source. In different dispersion models, one of simplest is the Gaussian model. In this approach it is supposed that emission plume obeys from Gaussian distribution and is... 

Due to the important role of base plates, both in transferring forces from the structure to the foundation, and also in transferring vibrations from soil to the structure, it is necessary to have sufficient knowledge on their behaviour and performance under monotonic and cyclic loading regimes. In fact, the behaviour of the supports of any structure cannot be identified without identifying the behaviour of its base plates. Numerous configurations with/without various types of attachments have been proposed and used for base plates. In this work, altogether six commonly-used types of base plates were studied and their behaviour under monotonic and cyclic loadings was obtained using commercial... 

Past earthquakes show that irregular structures have been more vulnerable than their regular counterparts. One of the common types of irregular buildings in urban areas is split-level ones. On the other hand, beam-to-column connections in steel structures are mostly of "semi-rigid" type. In this work, effects of different levels of rigidity of connections, 100%, 75%, 50% and 25%, on the behavior of a number of two-dimensional split-level steel structures, with 1.5 m difference in levels of floors, 2, 3, 5 and 6 bays, and 5, 10 and 15 stories, were studied. All frames were analyzed “with” and “without” considering the P-∆ phenomenon, with two methods, ‘equivalent static load,’ and ‘modal... 

In recent years, the idea of Homogenous charge compression ignition (HCCI) engines has been in the center of attention as a new generation of internal combustion engines. Intense decrease in pollutant emission rate like NOx, low fuel consumption and high thermal efficiency are the main reasons of why these engines are in center of attention, however, some drawbacks, which the main one combustion control which happens in limited operation range between knock and misfiring has limited the use of these engines. Hence approaches like adding synthesis gas, using exhaust gas recirculation, controling effective comperession ratio by using variable valve timing, changing the input conditions... 

Tehran, with approximately 750 km2 of land area, a population of more than 8 million people with about 4 million active on-road vehicles, is dealing with serious air pollution problems. To model the environmental phenomenon precisely, this study aims to develop on-road air pollutant emission factor matrices based on existing traffic in Tehran routes and to run air quality modelling within Tehran geographic boundaries. We developed emission factor matrices using SMOKES-MOVES emission modeling system. To do so, we calculated on-road emission factors from actual traffic-related data and run MOVES emission model. And use use them for different pollutants considered in air quality models. Then,... 

In this work the response modification factor (RMF), behaviour factor, of two-dimensional regular and split-level steel braced frames was worked out and presented. A total number of 840 frames with various number of stories, spans, braced spans and span lengths were studied. Frames were loaded based on ASCE 7-10 and designed in accordance with AISC 360-10. Static nonlinear analysis and Uang method were used for obtaining the RMFs of the studied frames. The effect of split-level irregularity and parameters such as number of stories on the RMF were worked out and are presented in this thesis. Linear regression was used to develop formulae for RMFs of regular and split-level braced frames.... 

Fire is one the events which threatens the very existence of every building, residential, office, industrial or else. However, this threat is more serious with regard to buildings with steel structures. Steel, despite its many advantages over other structural materials, such as having high strength to weight ratio, ductility, toughness and resilience, has the disadvantage of rapidly losing its strength at elevated temperatures, i.e. in fire. Therefore, it is the responsibility of the designer to make the serious decision of whether to use steel, concrete, timber, or other materials for the structure of the building to be designed. Observations made during full-scale fire tests as well as...