Loading...
Search for:
motamedi--sadegh
0.075 seconds
Investigation of Chaos in the Relativistic Restricted Three Body Problem
, M.Sc. Thesis Sharif University of Technology ; Pourtakdoust, Hossein (Supervisor)
Abstract
In this dissertation, initial conditions that cause chaotic movement in the relativistic restricted three body problem was obtained by the fast Lyapunov indicator and the time-frequency analysis. With general relativistic model, we can proceed with more accuracy in the design of stable orbit and this chaotic amplification effect could be used as a novel test of general relativity
Modification of nanostructure and improvement of mechanical properties of polypropylene/polyamide 6/layered silicate ternary nanocomposites through variation of processing route
, Article Composites Part B: Engineering ; Volume 85 , February , 2016 , Pages 207-215 ; 13598368 (ISSN) ; Bagheri, R ; Sharif University of Technology
Elsevier Ltd
2016
Abstract
Ternary nanocomposites of polypropylene/polyamide 6/layered silicate were prepared through three different processing procedures. X-ray diffraction and transmission electron microscopy were used to study the nanostructure of the samples, and tensile and impact strength measurements were conducted to assess the mechanical properties. It was shown that processing route has a significant effect on the delamination of clay platelets. Fully exfoliated nanostructure was achieved through a certain two-step processing route. Compatibilization of the blends affected microstructure as well as nanostructure. Mechanical properties were affected by changing the processing route, to a great degree....
Investigation of the nanostructure and mechanical properties of polypropylene/polyamide 6/layered silicate ternary nanocomposites
, Article Materials and Design ; Volume 31, Issue 4 , April , 2010 , Pages 1776-1784 ; 02641275 (ISSN) ; Bagheri, R ; Sharif University of Technology
2010
Abstract
This work aims to investigate the structure-property relationship in ternary nanocomposites consisting of polypropylene as the matrix, nanoclay as the reinforcement and polyamide 6 as the intermediate phase. In this regard, composites of polypropylene/organoclay, polyamide/organoclay, blends of polypropylene/polyamide, and ternary nanocomposites of polypropylene/polyamide/layered silicate with and without compatibilizer were produced via melt compounding. Nanostructure was investigated by wide-angle X-ray diffraction and transmission electron microscopy. Scanning electron microscopy was employed to study the microstructure. Modulus of elasticity and yield strength were measured by uniaxial...
Criteria in the Holistic and Analytic Rating of EFL Learners' Production of Agreement and Disagreement Speech Acts among Non-native English Teachers
, M.Sc. Thesis Sharif University of Technology ; Alemi, Minoo (Supervisor)
Abstract
Conveying a successful message within a language profoundly stems from not only a linguistically appropriate utterance, but also a pragmatically appropriate discourse too. Broadly considering various facets of pragmatics, pragmatic assessment has not been potentially brought into perspective, and, as a result, the literature deserves more comprehensive attention. This study, guided by the principles of mixed methods design, pursued three purposes: to inspect the matches and mismatches, to explore rating variations, and to assess the rater consistency between the holistic and analytic rating methods of agreement and disagreement speech acts in L2 by non-native English teachers. To address...
Study of the scratch resistance criteria and their relationship with mechanical properties and microstructure in a ternary thermoplastic blend
, Article Wear ; Volume 386-387 , 2017 , Pages 118-128 ; 00431648 (ISSN) ; Bagheri, R ; Sharif University of Technology
2017
Abstract
Polymeric materials generally suffer from a low resistance to various types of surface mechanical damage, among which scratch is a prominent example. While several attempts have been made to assess the scratch resistance and its relationship with the bulk mechanical properties in simple polymeric systems, the available research on the polymeric blends is scarce. This study attempts to fill this gap by studying the link between the scratch resistance and mechanical properties in a ternary polymeric nanocomposite, which has proved to feature superior and tunable mechanical properties. For this aim, blends of polypropylene and polyamide 6 were prepared using melt blending with two different...
Design and Synthesis of Heterogeneous Nanocatalysts Based on Immobilized Metals on Polymeric Substrates and their Applications in Organic Reactions
, Ph.D. Dissertation Sharif University of Technology ; Pourjavadi, Ali (Supervisor)
Abstract
Today, catalysts have shown the growing applications in chemical industries especially for drug synthesis. Using immobilized heterogeneous catalysts is a sensible way to benefit from advantages of both heterogeneous and homogeneous catalysts. In this regards, homogeneous catalysts are immobilized on to a solid support through various methods. However, low loading amount of homogenous part and subsequently insufficient catalytic activity are main limitations of immobilized heterogeneous catalysts. For this reason, polymeric supports have been introduced to immobilize metal ions or nanoparticles. These polymeric supports not only possess advantages such as anti-corrosive properties, simple...
Effecive & efficient DSM configuration guidelines for low-cost development of complex systems
, Article Gain Competitive Advantage by Managing Complexity - Proceedings of the 14th International Dependency and Structure Modelling Conference, DSM 2012, 13 September 2012 through 14 September 2012 ; 2012 , Pages 125-137 ; 9783446433540 (ISBN) ; Sharif University of Technology
Institution of Engineering Designers
2012
Abstract
With the proliferation of more complex systems has come the need to find better solutions in both technical and management domains. Such complex systems are usually larger in size, have more parallel operations and contain more complex interfaces (Eisner, 2005). The Design Structure Matrix is a very useful tool in handling such complexities, provided that the system designer can use it properly. This paper addresses how effectiveness & efficiency are defined for a DSM and how these two important characteristics can be achieved. The importance of understanding the solution space in constructing an effective & efficient DSM is discussed and general guidelines are given on configuring the DSM...
Developing an Integrated Framework for Outsourcing in the Auto Industry
, M.Sc. Thesis Sharif University of Technology ; Sheikhzadeh, Mehdi (Supervisor)
Abstract
Outsourcing is currently a challenging issue in the auto industry. On one hand, outsourcing has be-come a competitive imperative for automakers due to its significant benefits. On the other hand, it involves many aspects of risks that could potentially hurt core competencies of a firm. As such, in the auto industry, it is highly critical to make optimal outsourcing decisions for which an integrated framework offering a holistic view seems quite necessary. In this thesis, based on four fundamental research questions of “Who?”, “What?”, “Whom?” and “How?”, an integrated framework for outsourcing in the auto industry is developed in order to identify effective outsourcing factors and associated...
Ancillary service markets
, Article 2007 Large Engineering Systems Conference on Power Engineering, LESCOPE'07, Montreal, QC, 10 October 2007 through 12 October 2007 ; January , 2007 , Pages 316-320 ; 9781424415830 (ISBN) ; Fotuhi Firuzabad, M ; Sharif University of Technology
2007
Abstract
Ancillary services are generally referred as those services other than energy that are essential for ensuring reliable operation of electric power systems. This paper discuses different approaches for procuring required ancillary services for power system security. Furthermore, various design options for ancillary service markets are studied. Such markets are typically operated by an independent system operator (ISO). Different characteristics of each design option are also explained in this paper. The two most important factors which will be discussed for each design option are the price reversal phenomenon and total procurement cost. © 2007 IEEE
Thin Film Thickness Measurement Using Colors of Interference Fringes
, M.Sc. Thesis Sharif University of Technology ; Amjadi, Ahmad (Supervisor)
Abstract
There are several methods for measuring thin film thickness, however, for the analysis of liquid film motors [1] we need a method which is capable of measuring the thickness using a single image of the film. In this work, we use the colors that appear on thin films, such as soup bubbles, which is a result of light interference to calculate the thickness of the layer
Measure for Macroscopic Quantumness via Quantum Coherence and Macroscopic Distinction
, M.Sc. Thesis Sharif University of Technology ; Raeisi, Sadegh (Supervisor)
Abstract
One of the most elusive problems in quantum mechanics is the transition between classical and quantum physics. This problem can be traced back to the Schrodinger's cat. A key element that lies at the center of this problem is the lack of a clear understanding and characterization of macroscopic quantum states. Our understanding of Macroscopic Quantumness relies on states such as the Greenberger-Horne-Zeilinger(GHZ) or the NOON state. Here we take a first principle approach to this problem. We start from coherence as the key quantity that captures the notion of quantumness and demand the quantumness to be collective and macroscopic. To this end, we introduce macroscopic coherence which is the...
Structural Health Monitoring using Bayesian Optimization of the finite element model of structures and Kalman filter
, M.Sc. Thesis Sharif University of Technology ; Bakhshi, Ali (Supervisor)
Abstract
With confidence in the recorded observations, the RLS method no longer estimates the recorded measurements by sensors, i.e. the displacement and speed of the floors, and only estimates the parameters. In contrast, in the EKF method, in addition to estimating the structure's parameters, a more precise estimation of the observations recorded by the sensors has been done by accepting the noise in the recorded observations. These methods, which are based on the Bayesian updating, investigate the two primary sources of uncertainty in a problem: a) measurement noise or observation noise, and b) process noise, which includes modeling errors. In these methodologies, the unknown system parameters,...
Content Aware Packet Scheduling in Peer-to-Peer Video Streaming
, M.Sc. Thesis Sharif University of Technology ; Rabiee, Hamid Reza (Supervisor)
Abstract
The accessibility of broadband Internet to home users has pushed video broadcasting applications up, in the list of most favorite applications in todays Internet. Such applications involve delivering the data which generated in a single sender to a set of users which are scattered around the world. While it was formerly believed that the IP-Multicasting is the mean to provide this kind of services, the trend has altered to the use of Application Layer Multicasting techniques due to their deployment simplicty. Since their advent, Peer to Peer applications has mitigated many problems previously unsolved in the field of communication. File sharing, distributed file systems, distributed data...
Simulation of the Effect of Different Measures on the Amount of Water Entering the South of Lake Urmia Using the MIKE SHE Simulator Model
, M.Sc. Thesis Sharif University of Technology ; Tajrishy, Masoud (Supervisor)
Abstract
Sustainable management of water resources is an important issue today, because it can play a role in achieving environmental protection and economic prosperity. Lake Urmia is a remarkable ecological system, because it includes a unique habitat with native and migratory species, maintains the temperature balance of the region, prevents the formation of dust in the region and is one of the largest Tourism and recreational destinations and a source of income for many people in the Area. However, over the past two decades, the intensification of agricultural activities, the indiscriminate use of water, and climate fluctuations have put significant pressure on it and have led to a gradual...
Finding Semi-Optimal Measurements for Entanglement Detection Using Autoencoder Neural Networks
, M.Sc. Thesis Sharif University of Technology ; Raeisi, Sadegh (Supervisor)
Abstract
Entanglement is one of the key resources of quantum information science which makes identification of entangled states essential to a wide range of quantum technologies and phenomena.This problem is however both computationally and experimentally challenging.Here we use autoencoder neural networks to find semi-optimal measurements for detection of entangled states. We show that it is possible to find high-performance entanglement detectors with as few as three measurements. Also, with the complete information of the state, we develop a neural network that can identify all two-qubits entangled states almost perfectly.This result paves the way for automatic development of efficient...
Numerical Analysis and Optimization of A Vortex Tube with Differential Evolution Algorithm
, M.Sc. Thesis Sharif University of Technology ; Mazaheri, Karim (Supervisor)
Abstract
The vortex tube is a simple device that injects compressed gas (air) tangentially into the vortex chamber through one or more injection nozzles. After entering, the flow becomes rotational and an axial cold flow goes towards the cold outlet and a peripheral hot flow goes towards the hot outlet. Besides all the different applications of the vortex tube, the main application of this device is cooling. Here, the goal is to optimize the geometry and physical conditions to improve the performance, which is done by using a commercial software and numerical analysis of a vortex tube to understand the flow physics and optimization. In this research, we use experimental and numerical data for...
Optimum simultaneous clearing of energy and spinning reserve markets using cost/benefit analysis
, Article IEEE Power and Energy Society 2008 General Meeting: Conversion and Delivery of Electrical Energy in the 21st Century, PES, Pittsburgh, PA, 20 July 2008 through 24 July 2008 ; 2008 ; 9781424419067 (ISBN) ; Fotuhi Firuzabad, M ; Zareipour, H ; Sharif University of Technology
2008
Abstract
Considering the high level of interactions between energy and reserve markets, simultaneous clearing of these markets has been shown to provide more efficient solutions, than a sequential market clearing process. In addition, determining reserve requirements based on probabilistic approaches results in more economical efficiency, while maintaining an acceptable level of reliability, compared to deterministic approaches. This paper proposes a new method for clearing energy and spinning reserve markets simultaneously, while at the same time, spinning reserve requirements are determined based on a cost/benefit analysis as a probabilistic-based approach. This cost/benefit analysis considers both...
Content Based Community Extraction in Social Networks from Stream Data
, M.Sc. Thesis Sharif University of Technology ; Abolhassani, Hassan (Supervisor)
Abstract
Increasing in social communication via electronic ways has been made social network analysis of these communications more important each day. One of the most important aspects in social network analysis is community detection in such networks. There are many different ways to extract communities from social graph structure which in some of them the content of communication between actors has been noticed in community extraction algorithm. In this thesis after a short survey over advantages and disadvantages of existing methods for community detection, a new method for extracting communities from social networks has been suggested which in addition to streaming property of data it spot the...
Quantum Information Processing with NMR Spectroscopy
, M.Sc. Thesis Sharif University of Technology ; Raeisi, Sadegh (Supervisor)
Abstract
Quantum Information Processing (QIP) is one of the active areas of research in both theoretical and experimental physics. Any experimental technique that is used for a scalable implementation of QIP must satisfy DiVincenzo’s criteria [17]. Nuclear Magnetic Resonance (NMR) satisfies many of these conditions, but it is not scalable and cannot initialize the qubits to pure state [28]. NMR can be a great platform for studying the fundamentals of QIP. In this project, for a twoqubit system, we prepare pseudo pure states from the initial mixed states by using unitary operations and implement CNOT gates. According to the results of our experiments, we can apply all the gates with high fidelity....
Natural convection from a confined horizontal cylinder: The optimum distance between the confining walls
, Article International Journal of Heat and Mass Transfer ; Volume 44, Issue 2 , 2001 , Pages 367-374 ; 00179310 (ISSN) ; Razi, Y. P ; Sharif University of Technology
2001
Abstract
The laminar natural convection from an isothermal horizontal cylinder confined between vertical walls, at low Rayleigh numbers, is investigated by theoretical, experimental and numerical methods. The height of the walls is kept constant, however, their distance is changed to study its effect on the rate of the heat transfer. Results are incorporated into a single equation which gives the Nusselt number as a function of the ratio of the wall distance to cylinder diameter, t/D, and the Rayleigh number. There is an optimum distance between the walls for which heat transfer is maximum. © 2000 Elsevier Science Ltd. All rights reserved