Sharif Digital Repository

Hybrid nanoparticle comprising of nanosilica (NS) and nanodiamond (ND), denoted by ND@NS, was synthesized by a two-step chemistry route and then incorporated into styrene-butadiene rubber (SBR) at low concentrations up to 5 phr by a two-roll mill. Physical hybrids of NS and ND, i.e., ND&NS, with a weight ratio similar to chemical hybrid (80:20 for NS:ND), were also incorporated into SBR. Field emission scanning electron microscopy observations revealed very fine dispersion of nanoparticles in the case of physical hybrids (ND&NS). In contrast, agglomerations and aggregation of nanoparticles were evidenced for ND@NS. Tensile and dynamic mechanical analyses exhibited a higher reinforcing effect... 

The purpose of this research is to explain the surface modification of fabricated polyamide reverse osmosis (RO) membranes using UV-initiated graft polymerization at different irradiation times (15, 30, 60, and 90 s) and various acrylamide concentrations (10, 20, and 30 g L−1). Also, coating of membranes surface with various concentrations of TiO2 nanoparticles (10, 20, 30, and 50 ppm) followed by the same UV irradiation times was investigated. After that, the membranes modification was done by grafting of acrylamide blended with TiO2 nanoparticles via UV irradiation. The characterization of membranes surface properties and their performance were systematically carried out. The results... 

An optical amplifier followed by a bistable element has been statistically analyzed before [1]. In this manuscript, output noise analysis represents, then signal to noise ratios (SNR) are calculated either for input or output. It will be shown that noise reduction, can be achieved by a proper selection of parameters  

Control Performance Assessment (CPA) and tuning of PID controllers are studied in this paper. We propose a framework for systematic analysis of the tradeoff between the structural complexity of the controller and its performance. As the measure of the controller performance, an LQG based index is used. The problem is augmented with an additional term which forces sparsity on the complexity of a decentralized PID controller. The desired complexity is controlled via a weighting parameter which determines the cost of each additional element (i.e., P, I, and D terms). The result is a decentralized multivariable PID controller in which the complexity of each loop controller is optimized such that... 

Control Performance Assessment (CPA) and tuning of PID controllers are studied in this paper. We propose a framework for systematic analysis of the tradeoff between the structural complexity of the controller and its performance. As the measure of the controller performance, an LQG based index is used. The problem is augmented with an additional term which forces sparsity on the complexity of a decentralized PID controller. The desired complexity is controlled via a weighting parameter which determines the cost of each additional element (i.e., P, I, and D terms). The result is a decentralized multivariable PID controller in which the complexity of each loop controller is optimized such that... 

One of the distributed solutions for scaling Web Search Engines (WSEs) may be peer-to-peer (P2P) structures. P2P structures are successfully being used in many systems with lower cost than ordinary distributed solutions. However, the fact that they can also be beneficial for large-scale WSEs is still a controversial subject. In this paper, we introduce challenges in using P2P structures to design a large-scale WSE. Considering different types of P2P systems, we introduce possible P2P models for this purpose. Using some quantitative evaluation, we compare these models from different aspects to find out which one is the best in order to construct a large-scale WSE. Our studies indicate that... 

Crack detection is a vital component of structural health monitoring. Several computer vision-based studies have been proposed to conduct crack detection on concrete surfaces, but most cases have difficulties in detecting fine cracks. This study proposes a deep learning-based model for automatic crack detection on the concrete surface. Our proposed model is an encoder–decoder model which uses EfficientNet-B7 as the encoder and U-Net’s modified expansion path as the decoder. To overcome the challenges in the detection of fine cracks, we trained our model with a new training strategy on images extracted from an open-access dataset and achieved a 96.98% F1 score for unseen test data. Moreover,... 

Crack detection is a vital component of structural health monitoring. Several computer vision-based studies have been proposed to conduct crack detection on concrete surfaces, but most cases have difficulties in detecting fine cracks. This study proposes a deep learning-based model for automatic crack detection on the concrete surface. Our proposed model is an encoder–decoder model which uses EfficientNet-B7 as the encoder and U-Net’s modified expansion path as the decoder. To overcome the challenges in the detection of fine cracks, we trained our model with a new training strategy on images extracted from an open-access dataset and achieved a 96.98% F1 score for unseen test data. Moreover,...