Loading...
Search for: moussavi-torshizi--abolfazl
0.158 seconds

    Experimental and numerical investigations of radial flow compressor component losses

    , Article Journal of Mechanical Science and Technology ; Vol. 28, issue. 6 , 2014 , p. 2189-2196 Mojaddam, M ; Hajilouy-Benisi, A ; Abolfazl Moussavi-Torshizi, S ; Movahhedy, M.R ; Durali, M ; Sharif University of Technology
    2014
    Abstract
    This research numerically and experimentally investigates a small turbocharger radial flow compressor with a vane-less diffuser and volute. The geometry of the compressor is obtained via component scanning, through which a 3D model is prepared. The flow inside this model is numerically analyzed by using a Navier-Stokes solver with a shear-stress transport turbulence model. The characteristic curves of the compressor and the contributions of its components to total pressure drop are acquired by measuring the static and total pressures at different cross sections of the compressor. Numerical results are verified with the experimental test results. The model results exhibit good agreement with... 

    Modifications in Commercial Diesel Engines to Perform Under Difficult Respiration Conditions

    , M.Sc. Thesis Sharif University of Technology Moussavi Torshizi, Abolfazl (Author) ; Durali, Mohammad (Supervisor)
    Abstract
    In this project we are about to adopt a method for implementing commercial diesel engines (truck and bus engines) in applications with difficult respiration condition like what happens in a submarine. To this end, working conditions of such engines are introduced and standard constraints are explained. Then the structure of already manufactured submarine engines is presented. At this point an engine from known manufacturers was selected for calculations to be performed on it. Since test and measurement equipments were not yet ready, simulation using computer software (GT-POWER v6.1) was selected as the solving method. First, the engine was modeled in its nominal working conditions. After... 

    Multilevel optimization of the splitter blade profile in the impeller of a centrifugal compressor

    , Article Scientia Iranica ; Volume 24, Issue 2 , 2017 , Pages 707-714 ; 10263098 (ISSN) Moussavi Torshizi, S. A ; Hajilouy Benisi, A ; Durali, M ; Sharif University of Technology
    Sharif University of Technology  2017
    Abstract
    In this research, multi-level optimization of the profile of the splitter blades of a turbocharger compressor is performed using genetic algorithm in order to improve its performance. Successive corrections of the profile at hub, mid-span, and shroud of the splitter blades, with the objective of decreasing the incidence losses at the leading edge and adjustment of the blade loading at the shroud, result in an impeller having improved splitter blades. The impeller flow field analysis shows that the optimization has been successful in reducing the flow leakage at the shroud region as well as the losses in the leading edge region. Although numerical simulations predict a decrease by 0.5% in... 

    Design, Optimization and Numerical and Experimental Investigation of the Impeller of a Centrifugal Compressor under Geometric Constraints

    , Ph.D. Dissertation Sharif University of Technology Moussavi Torshizi, Abolfazl (Author) ; Hajilouy Benisi, Ali (Supervisor) ; Durali, Mohammad (Supervisor)
    Abstract
    Centrifugal compressors are vastly implemented in the industry due to their higher pressure ratio per stage. So, researches are still going on to improve the performance of these devices. On this way, the current project is defined to perform geometrical optimization in the impeller of a centrifugal compressor using numerical and experimental methods. In this research, the design process of centrifugal compressors is first discussed according to methods and guidelines provided in several references. Then the compressor of the GT4082 turbocharger is redesigned using these theories. It is shown that overall available rules are enough to design an acceptable centrifugal compressor. Experimental... 

    Numerical optimization and manufacturing of the impeller of a centrifugal compressor by variation of splitter blades

    , Article ASME Turbo Expo 2016, Turbomachinery Technical Conference and Exposition, 13 June 2016 through 17 June 2016 ; Volume 8 , 2016 ; 9780791849866 (ISBN) Moussavi Torshizi, S. A ; Hajilouy Benisi, A ; Durali, M ; International Gas Turbine Institute ; Sharif University of Technology
    American Society of Mechanical Engineers (ASME)  2016
    Abstract
    Design and optimization of centrifugal compressors, based on main blades configuration of impeller have been vastly discussed in open literature, but less researches have addressed splitters. In this research, the impeller of a commercial turbocharger compressor is investigated. Here, profiles of main blades are not changed while the effect of changing the configuration of splitters is studied. An optimization study is performed to find the best configuration using genetic algorithm over a complete operating curve of the compressor. CFD codes with experimental support are used to predict the compressor performance. Quantumetric tests beside destructive analysis of two impellers are... 

    Design and Prototyping a High Speed 60 kW Spindle Incorporated Air Turbine

    , M.Sc. Thesis Sharif University of Technology Moussavi, Hossein (Author) ; Durali, Mohammad (Supervisor)
    Abstract
    Regarding the price of industrial turbo machines, testing the rotating elements of them is always an important issue. One of the companies of the aviation industry decided to design and fabricate a spin tester device to check the quality of new rotating parts before installing them on gas turbines. A team has worked on this project for more than a one year. The present thesis is on designing the drive system of the spin tester. The drive system was chosen to be an air motor. This thesis concentrates on the design procedure of this air motor. The designed system is capable of providing enough power to accelerate the disks to the test speed in the appropriate time. The disk geometry, test... 

    Learning improvement by using matlab simulator in advanced electrical machine laboratory

    , Article RPC 2010 - 1st Russia and Pacific Conference on Computer Technology and Applications, 6 September 2010 through 9 September 2010 ; 2010 , Pages 107-116 Zeinolabedin Moussavi, A. S ; Fazly, M ; Sharif University of Technology
    2010
    Abstract
    This paper presents how can teach complicated problems in electrical engineering subjects (electrical machines) by using simulators such as MATLAB/SIMULINK. Simulation of direct vector control of induction machine (IM) drive on the rotor flux direction with composite model flux observer can improve electrical machine teaching-learning procedure for graduated and under graduated levels. In the indirect vector control of IM, current reference values are used for estimation angle of the rotor flux space vector (ARFSV), however using current reference values instead of current real values can decrease accuracy of ARFSV. In the direct vector control, current real values (current feedback)... 

    Analysis of Factors Affecting IPO Initial Returns of the Tehran Stock Exchange

    , M.Sc. Thesis Sharif University of Technology Kanani Torshizi, Mostafa (Author) ; Talebian, Masoud (Supervisor) ; Ebrahimnejad, Ali (Supervisor)
    Abstract
    In the present study, the factors that affect the IPO underpricing in the Tehran Stock Exchange are investigated. We define the variables of IPO percentage, age and size of companies, dummy variable for rounded IPO prices, market return in a month before the initial public offering, average return of IPOs that had been done during one month before the IPO of each ticker and the dummy variable for industrial group in which the company is located. We had to calculate the initial return of 246 companies that were offered in the years 1380 to 1395. In this study, due to the existence of a daily stock price volatility constraint, a new algorithm was introduced to calculate the dependent... 

    Effect of splitter leading edge location on performance of an automotive turbocharger compressor

    , Article Energy ; Volume 123 , 2017 , Pages 511-520 ; 03605442 (ISSN) Moussavi, S. A ; Hajilouy Benisi, A ; Durali, M ; Sharif University of Technology
    Elsevier Ltd  2017
    Abstract
    Design of centrifugal compressors can be accomplished using methods provided in text books and open literature. In this general approach, after determination of dimensions in meridional plane, blade profiles are designed using aerodynamic methods. Then, some blades are trimmed at the beginning to avoid inlet blockage. But there is no clear guidance on how this trimming must be performed. With this widely implemented method, splitter blades have the same profile as main ones. In this research, blade profiles and dimensions of the compressor impeller are not changed while the effect of changes in the position and angle of splitters leading edge are investigated. An optimization scheme is... 

    Application of Gis & Fuzzy Technique for Order-Preference by Similarity to Ideal Solution (Topsis) in Siting Water Reservoires

    , M.Sc. Thesis Sharif University of Technology Jozaghi, ali (Author) ; Shamsai, Abolfazl (Supervisor)
    Abstract
    Sustainable agricultural development in the country without regard to water supply problems in terms of time and place is not possible. Construction of water storage tanks filled with water and seasonal use in dry seasons in the effective action in the optimal use of water in the climate of (low and irregular rainfall) is. The most important step in the construction of water storage tanks to choose the best point for the construction of the reservoir basin in order to reduce costs and increase efficiency. Chndmyarh different methods to decide the best option for finding a few options from there. Among these methods can be Tapsys two methods (TOPSIS) and hierarchical analysis (AHP) pointed... 

    Efficient Management of River Water Quality Based on Pollution Trading Approach

    , Ph.D. Dissertation Sharif University of Technology Sarang , Amin (Author) ; Shamsai, Abolfazl (Supervisor)
    Abstract
    “Sustainable development” is a frequently used phrase, but the idiom has been experienced little since it was coined by the Brundtland, due to its intrinsic complications. The issue is going to compromise two key components; economy and ecology. One of the solutions based on concept of sustainable development that has been proposed for maintaining water quality at acceptable levels is to cap pollutant emissions at a sustainable level, then establish an economic market in which the right to discharge pollutants is traded according to market supply and demand mechanisms. Water quality trading or pollution trading is one such kind of market-based program that has also been described using names... 

    Assessment of Optimum Environmental Flows Using Economic Evaluation Methods

    , M.Sc. Thesis Sharif University of Technology Mazdarani, Sohrab (Author) ; Shamsai, Abolfazl (Supervisor)
    Abstract
    One of the main challenges of Water Resources Planning and Management (WRPM) is to balance water allocation between different uses. Usually, due to political and economic power of other uses, ecosystem receives less attention. Environmental flow is the allocated flow to ecosystem. Ecosystem provides a wide range of services to humanity. Therefore, environmental flow is not exclusively a matter of sustaining ecosystem but also a matter of providing humans with better life. Several methods have been developed to determine the environmental flow but only a few consider its socio-economic aspects. Consideration of these aspects could assist decision-makers with determining the optimum flow and... 

    Numerical Study of Geotextile Application in Downstream Filter Zone of an Embankment Dam with Clay Core

    , M.Sc. Thesis Sharif University of Technology Maghsoodian, Maedeh (Author) ; Shamsaie, Abolfazl (Supervisor)
    Abstract
    Nowadays, applications of the synthetic materials are developing in civil engineering projects and widely used in these projects. Therefore, during previous years; use of the Geotextiles as one of the Geosynthetic materials in order to filtration, drainage, separation, soil protection, etc have developed ever-increasing. The goal of this research is modeling and studies of the Geotextiles application in the downstream filter zone of embankment dams in combination with granular materials using FLAC2D software. Gordeh Bin embankment dam situated in West Azerbaijan province has been chosen as case study. In this matter, different models have been made with changes in thickness of the inclined... 

    , M.Sc. Thesis Sharif University of Technology Nazari, Fatemeh (Author) ; Shamsaei, Abolfazl (Supervisor)
    Abstract
    Entrance of air to close water conduits occurs in many ways. This phenomenon makes displeasing effects on water transport structures. Two-phase flows in closed conduits are studied experimentally, numerically and theoretically. Even after decades, due to the complexity of the subject, these studies still require development and reformation. Numerical and theoretical two-phase models are often limited to a special regime of flow."Volume Of Fluid"(VOF) is a model for non-mixing two-phase flows. "Fluent" software uses this model in this field of flows. Volume of fluid is used successfully in some problems like dam break or rising bubbles. Main disadvantage of this model is distribution of the... 

    Assessment of waterlogging and provide risk maps by using RS, GIS and field data (case study: Qazvin plain)

    , M.Sc. Thesis Sharif University of Technology Mansourian, Hamid (Author) ; Shamsaei, Abolfazl (Supervisor)
    Abstract
    Groundwater quality protection has a significant importance due to abundant applications of these resources in various fields such as agriculture, industry and drinking water. Removal of groundwater pollution is a time and money consuming process and often pollution is detected when improving the quality of groundwater is nearly impossible. For this vulnerability assessment there are three methods: Processing, Overlap-Index and Statistical Methods. Overlap-Index is composed of variety of maps such as Geology, Soil, Groundwater Depth and etc which uses in determining of vulnerability Index. In the present study for underground pollution potential determining, four indexes such as AVI، GOD،... 

    groundwater level fluctuations forecasting using conjunction models of Wavelet - Neural-Fuzzy Network (WNF) and Wavelet-Neural Network (WNN) and linear model of ARIMA (case study: Qom plain

    , M.Sc. Thesis Sharif University of Technology Fathi, Bahman (Author) ; Shamsaei, Abolfazl (Supervisor)
    Abstract
    Prediction of groundwater level fluctuations is absolutely necessary for the proper manag ement of these precious resources. There are different methods to predict hydrological time series such as groundwater level. Linear models inefficiency in predicting nonlinear and n on-stationary time series cause researchers widely use artificial intelligence techniques such as Artificial Neural Networks (ANN), Fuzzy Inference System (FIS), Genetic Algorithm (GA) and their hybrid models such as Artificial Neural – Fuzzy Inference System (ANFIS). These smart models are capable to simulate nonlinear and non-stationary time series in suitable accu-racy using by a few time and data. By emersion of Wavelet... 

    GIS Based Procedure to Determine Location of Cascade Small Hydropower Plants Case Study, Nokhan Area

    , M.Sc. Thesis Sharif University of Technology Serpoush, Behrad (Author) ; Shamsai, Abolfazl (Supervisor)
    Abstract
    Coinciding with the worldwide environmental issues and increasing demand for clean energy sources, hydropower plants have highly attracted decision- makers attention. Low manufacturing costs and pollutions which are made by these plants in comparison with another types of powerhouses, could be reason of that. And so on, hydropower locating and evaluating studies have been highly increased recently, specifically in developing countries. From the point of operation procedure, hydropower plants are generally divided in two types, run-of-he-river and storage projects. This study has concentrated on run-of-he-river projects and due to spotting plant location, Sefidbarg river basin... 

    Investigation of bed Stability in Downstream for the Diversion dam under Scour (Mill & Moghan case study)

    , M.Sc. Thesis Sharif University of Technology Gorji, Faeze (Author) ; Shamsai, Abolfazl (Supervisor)
    Abstract
    Numerical simulations and large eddy simulations (LES) of turbulent flow downstream of diversion dam , pool-riffle bedform in different geometrical ratios (different lengths of riffle and pool) with flow Reynolds number of 3.0 E+04 to 3.3E+04, downstream of special case study "Mill and Moghan diversion dam" with Froude number of 0.5 are presented The calculations are performed using a computational fluid dynamics model, FLOW-3D, which solves the Navier-Stokes equations in three dimensions with finite volume method. Numerical simulations are validated by comparing the numerical results of time-averaged flow patterns downstream of pool-riffle sequence with that of the experimental... 

    Hydro-economical Method for the Optimal Capacity Design of Small Hydropower Plant (Case Study: Kohneh Lahijan Hydropower Plant)

    , M.Sc. Thesis Sharif University of Technology Mehrvand, Shahryar (Author) ; Shamsai, Abolfazl (Supervisor)
    Abstract
    In this thesis, we determine the optimal capacity of the power plants considering site specifications and Flow Duration Curve and evaluating economic parameters. Finally a design with more sufficient economical and hydrualical performance would be selected. The optimization algorithm used in this thesis is called "Charged System search" that is one of the newest meta-heuristic algorithms. This algorithm is inspired by the coulomb and gauss's laws of electrostatics in physics and utilizes a number of charged particles which influence each other based on their fitness values and their separation distances considering the governing law of coulomb.The proposed method in this thesis can be... 

    Semi-supervised Breast Cancer Subtype Clustering Using Microarray Datasets

    , M.Sc. Thesis Sharif University of Technology Vasei, Hamed (Author) ; Motahhari, Abolfazl (Supervisor)
    Abstract
    Gene expression microarrays can be used for precision medicine and targeted therapies. The data generated by microarrays are high-dimensional causing statistical inference of any parameter a daunting task. In this thesis, it is shown that regardless of high-dimensional datasets produced by microarrays, the inference can be robust in the sense that random selection of features results in the same conclusion as far as the number of selected features are chosen appropriately. Stratifying patients with breast cancer based on their gene expression levels shows that patient subtypes are almost independent of the feature selection strategy. Moreover, using less noisy datasets coming from RNAseq...