Loading...
Search for: nazari--pegah
0.179 seconds

    Drop formation from a capillary tube: comparison of different bulk fluid on newtonian drops and formation of newtonian and non-newtonian drops in air using image processing

    , Article International Journal of Heat and Mass Transfer ; Volume 124 , 2018 , Pages 912-919 ; 00179310 (ISSN) Nazari, A ; Zadkazemi Derakhshi, A ; Nazari, A ; Firoozabadi, B ; Sharif University of Technology
    2018
    Abstract
    The formation of water drops as a Newtonian fluid and formation of a shear-thinning non-Newtonian fluid, Carboxyl Methyl Cellulose (CMC) from a capillary into different bulk fluids are experimentally investigated. A high speed camera is used to visualize the images of the drops and an image-processing code employed to determine the drop properties from each image. It was found that the properties of the water drops when they are drooped into the liquids bulk fluids such as toluene and n-hexane are almost the same while they differed substantially when they were drooped into the air bulk fluid. It is shown that during the formation of water drop in all three kinds of bulk fluids, the drop... 

    An Uplink Packet Scheduling Algorithm in Fixed PMP WiMAX Networks with TDD Frame Structure

    , M.Sc. Thesis Sharif University of Technology Nazari, Sonia (Author) ; Beigy, Hamid (Supervisor)
    Abstract
    Worldwide interoperability for Microwave Access (WiMAX) is one of the most dominant cell-based broadband wireless metropolitan access technologies. Packet scheduling algorithm specifies the packet transmission order. In WiMAX standard, packet scheduling algorithm is not defined and its efficient design is left for developers and researchers. The existing researches in the scope of uplink packet scheduling, which is the most challenging packet scheduling scheme, consider only one cell. However the uplink available resources might not be enough when there are many packets that should be scheduled. To solve this problem, we propose an algorithm that uses the load balancing mechanisms that are... 

    , M.Sc. Thesis Sharif University of Technology Nazari, Fatemeh (Author) ; Shamsaei, Abolfazl (Supervisor)
    Abstract
    Entrance of air to close water conduits occurs in many ways. This phenomenon makes displeasing effects on water transport structures. Two-phase flows in closed conduits are studied experimentally, numerically and theoretically. Even after decades, due to the complexity of the subject, these studies still require development and reformation. Numerical and theoretical two-phase models are often limited to a special regime of flow."Volume Of Fluid"(VOF) is a model for non-mixing two-phase flows. "Fluent" software uses this model in this field of flows. Volume of fluid is used successfully in some problems like dam break or rising bubbles. Main disadvantage of this model is distribution of the... 

    A new distributed uplink packet scheduling algorithm in WiMAX newtorks

    , Article Proceedings of the 2010 2nd International Conference on Future Computer and Communication, ICFCC 2010, 21 May 2010 through 24 May 2010 ; Volume 2 , May , 2010 , Pages V2232-V2236 ; 9781424458226 (ISBN) Nazari, S ; Beigy, H ; Sharif University of Technology
    2010
    Abstract
    Worldwide interoperability for Microwave Access (WiMAX) is designed to support a wide range of Quality of Service (QoS) requirements for different applications. Unlike the single service networks, a priority based mechanism is needed for specifying the transmission order of packets belonging to different traffic sources according to their QoS characteristics, which is called packet scheduling. In WiMAX standard, packet scheduling algorithm is not defined and its design is left for researchers. In this work, we propose a distributed uplink packet scheduling algorithm. In the proposed algorithm, when uplink capacity cannot satisfy the required resource of connections, according to traffic... 

    Synthesis of Graphene Oxide-based Polymer Nanocomposites and Investigation of Their Ability in Dye Adsorption

    , Ph.D. Dissertation Sharif University of Technology Nazari, Mojtaba (Author) ; Pourjavadi, Ali (Supervisor)
    Abstract
    In this project, polymer nanocomposites containing graphene oxide were prepared and used for adsorption of several cationic and anionic dyes. In most cases, these nanocomposites were prepared as three-dimentional polymer networks which contain graphene oxide. Nanocomposites with direct grafting of polymer chains onto the surface of graphene oxide were also prepared. Graphene oxide is an oxidized carbonaceous material with unique properties. This material has high surface area, good mechanical strength and various functional groups. Polymeric compounds with different functional groups, structures and properties can be prepared and used. By preparing composites of graphene oxide and polymers,... 

    Design and Implementation of a Master Robot for a Fracture Reduction Robotic Telesurgery System

    , M.Sc. Thesis Sharif University of Technology Nazari, Kianoosh (Author) ; Farahmand, Farzam (Supervisor)
    Abstract
    Common fracture treatments include open reduction and intramedullary nailing technology. However, these methods have disadvantages such as intraoperative X-ray radiation, delayed union or nonunion and postoperative rotation. Robots provide a novel solution to the aforementioned problems while having new challenges. The robotic system used in the study by providing more precise motion and exerting higher amount of forces makes the operation procedure more straightforward. In a normal operation 300-400 N of extension force would be needed which is fully provided by the surgen which leads to physical his/her (khastegi), by using the robotic system however, this force is simply provided without... 

    Study on Optimization of the EDC Model for Highly Preheated and Diluted Condition

    , M.Sc. Thesis Sharif University of Technology Nazari, Aslan (Author) ; Mardani, Amir (Supervisor)
    Abstract
    Moderate and Intense Low-oxygen Dilution(MILD) is the new member of combustion field. Highly preheated reactants and lowering the oxygen level in MILD combustion has some promising advantages. In this study the MILD burner, Jet-in-Hot-Coflow(JHC), is taken as the main test case. In this Research, Eddy Dissipation Concept combustion model ,introduced by Magnussen et al,is investigated in detail and governing equations are re-extracted. EDC combsution model due to moderate compuational cost in comparison with other combustion model and well prediction ability has drawn attention. Simulations on the Jet-in-Hot-Coflow(JHC) has shown the promising performance of the EDC combustion model. It seems... 

    Online High-bandwidth Network Application Detection Using Stream Classification

    , M.Sc. Thesis Sharif University of Technology Nazari, Ziaeddin (Author) ; Jalili, Rasool (Supervisor)
    Abstract
    Trac classication in today’s high-bandwidth networks is challenging, resource consuming, and inaccurate due to the high volume, velocity, and variety aracteristics of the network trac. Trac aracterization and Application identication teniques are widely addressed in the current literature. Due to the massive volume and streaming data in recent years, stream algorithms have been considered by many researers in dierent areas. Online application detection is an issue that has been addressed less frequently in literature. In this thesis, we investigate the performance of 10 dierent stream classication algorithms along with traditional classication algorithms. To generate a robust classier for... 

    Developing an Integrated Model of Management of Energy-Water Nexus in Industrial Ecosystems based on the Concept of Circular Economy(Case Study: South Pars Region)

    , M.Sc. Thesis Sharif University of Technology Nazari, Erfan (Author) ; Saboohi, Yadollah (Supervisor)
    Abstract
    The purpose of the present study is to plan an industrial system, over a period of 10 years, so that over time, while supplying the required demand, to optimal resource utilization with regard to material reuse and recovery flows of losses as well as the use of renewable resources move to implement the concept of a circular economy. One of the main incentives for the transition to a circular economy is carbon tax policy, which has been taken into account. The results of the decision-making model based on cost and flow constraints indicate that the use of carbon dioxide as a by-product of Pars Petrochemical Extraction Unit in order to produce urea in Pardis petrochemical industry in addition... 

    Workflow Ensembles Scheduling Improvement in Edge-Based Infrastructures

    , M.Sc. Thesis Sharif University of Technology Nazari, Zahra (Author) ; Habibi, Jafar (Supervisor)
    Abstract
    In the cloud computing environment, although many processing resources for application software with the volume of calculations The above is available, but it may not work for software that is sensitive to latency. In fact, due to the large distance between users and end devices to cloud servers, sending requests And the required data to the data centers requires a high bandwidth and therefore the data transfer time is also significant. In addition, cloud computing in platforms such as cloud-based IoT architecture faces other challenges such as connectivity, resource limitations of end devices, and security. In order to solve the challenges in the cloud computing environment and respond to... 

    Investigation of the Effects of Aging and Process Variation on Reliability in SRAM Based Memory Circuits

    , M.Sc. Thesis Sharif University of Technology Nazari, Reza (Author) ; Miremadi, Ghassem (Supervisor)
    Abstract
    Negative Bias Temperature Instability (NBTI) in CMOS devices is known as the major source of aging effect leading to performance and reliability degradation in modern processors. Instruction-cache (I-cache), which has a decisive role in performance and reliability of the processor, is one of the most affected modules by NBTI. Variations in duty Cycles and long-time residency of data blocks in I-cache lines (stress condition) are the two major causes of NBTI acceleration. This paper proposes a novel I-cache management technique to minimize the aging effect in the I-cache SRAM cells. The proposed technique consists of a smart controller that monitors the cache lines behavior and distributes... 

    Stable throughput analysis for a cooperative WLAN with primary and secondary users

    , Article 2012 6th International Symposium on Telecommunications, IST 2012 ; 2012 , Pages 535-540 ; 9781467320733 (ISBN) Nazari, M. A ; Ashtiani, F ; Sharif University of Technology
    2012
    Abstract
    In this paper, we propose a new scenario in order to increase the total throughput of a WLAN. In this scenario, some secondary users (SUs) are considered in a primary WLAN such that SUs cooperate with primary users (PUs) in transmitting the primary packets. Each SU sends its packets as well as the primary packets collided at the access point, but overheard successfully at the SU, by random access the primary WLAN. We show that SUs cooperation is able to compensate their adverse effect in the WLAN, so total throughput in the WLAN increases without a significant degrading effect for the stability region of PUs. To this end, we use an analytical model based on open queueing networks. By solving... 

    Sparse Representation-based Classification and Application to Image and Speech Processing

    , M.Sc. Thesis Sharif University of Technology Nazari, Milad (Author) ; Babaeizadeh, Masoud (Supervisor)
    Abstract
    Pattern recognition is a branch of machine learning that is used to identify patterns and regularities in data. Many classifiers have been designed for this purpose that their number grows daily. A classification method which in recent years has attracted much attention is the Sparse Representation based-Classification (SRC). SRC which is a combined result of machine learning and compressed sensing, was used for face recognition and showed good classification performance on face image data. However, SRC could not well classify some other datasets. Some methods such as Block-SRC Weighted-SRC and ernel-SRC to classify different types of dataset are proposed that maintain highest accuracy on... 

    On the minimization of the exit profile curvature in extrusion through multi-hole dies: a methodology and some verifications

    , Article Meccanica ; Volume 50, Issue 5 , May , 2015 , Pages 1249-1261 ; 00256455 (ISSN) Nazari Onlaghi, S ; Assempour, A ; Sharif University of Technology
    Kluwer Academic Publishers  2015
    Abstract
    In this study, a methodology has been presented for radial positioning of the die holes in multi-hole extrusion of non-symmetric sections. The objective of radial positioning is to minimize exit profile curvature. For this purpose, a two-hole die with non-symmetric T-shaped holes has been investigated. A kinematically admissible velocity field at deformation zone has been developed. The deformation region includes the dead metal zone (DMZ) which is assumed to be linear. The DMZ length was obtained by energy minimization through the upper bound method. To predict the exit profile curvature a deviation function has been suggested. Using the proposed function, the velocity field has been used... 

    Computational modeling of strong and weak discontinuities using the extended finite element method

    , Article Mechanics of Advanced Materials and Structures ; Volume 23, Issue 5 , 2016 , Pages 578-585 ; 15376494 (ISSN) Moradi, A ; Adib Nazari, S ; Sharif University of Technology
    Taylor and Francis Inc  2016
    Abstract
    In this article, the extended finite element method is employed to solve problems, including weak and strong discontinuities. To this end, a level set framework is used to represent the discontinuities location, and the Heaviside and Branch function are included in the standard finite element method. The case of two arbitrary curved cracks is solved numerically and stress intensity factor (SIF) values at the crack tips are calculated based on the evaluation of the crack tip opening displacement. Afterwards, J-integral methodology is adopted to evaluate the SIFs for isotropic and anisotropic bi-material interface crack problems. Numerical results are verified with those presented in the... 

    Enhanced recovery and recycling of catalyst by post-impregnation of γ-Al2O3 with 12-tungstophosphoric acid for esterification reaction

    , Article Canadian Journal of Chemical Engineering ; Volume 96, Issue 5 , 2018 , Pages 1176-1184 ; 00084034 (ISSN) Nazari, P ; Rahman Setayesh, S ; Sharif University of Technology
    Wiley-Liss Inc  2018
    Abstract
    12-tungstophosphoric acid, polyoxometalate with Keggin structure, and γ-Al2O3 were synthesized. Loading of 12-tungstophosphoric acid (HPW) on γ-Al2O3 was performed by the post-impregnation method. The catalysts were characterized by XRD, SEM, FTIR, BET, and DRS techniques. According to the pertinent observation, using the post-impregnation method promises the stability of polyoxometalate Keggin structure after loading on γ-Al2O3 support. The stability of 20 %HPW/Al2O3 was also confirmed by a leaching test. Textural characterization demonstrates that HPW on the γ-Al2O3 had a much larger surface area as compared with the pure HPW. The 20 %HPW/Al2O3 exhibited roughly high activity toward an... 

    A constructive genetic algorithm for LBP in face recognition

    , Article 3rd International Conference on Pattern Analysis and Image Analysis, IPRIA 2017, 19 April 2017 through 20 April 2017 ; 2017 , Pages 182-188 ; 9781509064540 (ISBN) Nazari, A ; Shouraki, S. B ; Sharif University of Technology
    2017
    Abstract
    LBP coefficients are essential and determine the priority of gray differences. The objectives of this paper are to reveal this and propose a method for finding an optimal priority through the genetic algorithm. On the other hand, the genetic operators such as initialization and cross-over operators, generate invalid coefficients, defective chromosomes. This paper also recommends a rectifying method for correcting defective chromosomes. Results on the FERET and Extended Yale B datasets indicate that the proposed method has markedly higher recognition rates than LBP. © 2017 IEEE  

    Effective degradation of Reactive Red 195 via heterogeneous electro-Fenton treatment: theoretical study and optimization

    , Article International Journal of Environmental Science and Technology ; 2018 ; 17351472 (ISSN) Nazari, P ; Setayesh, S. R ; Sharif University of Technology
    Center for Environmental and Energy Research and Studies  2018
    Abstract
    Abstract: The magnetite (Fe3O4) nanoparticles were synthesized and supported on the reduced graphene oxide. The characterization of the catalyst was performed by FT-IR, VSM, SEM, XRD, and BET techniques. The obtained results indicated that the in situ synthesis of Fe3O4 using coprecipitation method caused the homogenous formation of magnetite nanoparticles on the surface of reduced graphene oxide (average particle size ~ 71.032 nm) with high stability and catalytic activity toward electro-Fenton removal of Reactive Red 195. The effect of various factors (current intensity, initial pollutant concentration, catalyst weight, and pH) was evaluated by response surface methodology using central... 

    Wax Deposition Study During Offshore under Balanced Drilling

    , M.Sc. Thesis Sharif University of Technology Nazari, Aliakbar (Author) ; Jamshidi, Saeed (Supervisor)
    Abstract
    Wax deposition is one of the main problems in the oil industry. The formation of wax deposition causes problems such as reducing the effective tube radius, increasing pressure, reducing the flow capacity and etc. Even crude oil waxes can block the pipeline due to deposition of wax during crude oil production and transportation operations. If wax deposition is well predicted and effective parameters are well known and studied, they can be useful in reducing the deposition of wax, and consequently its problems and wax deposition costs will be significantly reduced. In this research, wax deposition has been investigated in Underbalanced drilling by OLGA software. In the first part, by... 

    Effective degradation of Reactive Red 195 via heterogeneous electro-Fenton treatment: theoretical study and optimization

    , Article International Journal of Environmental Science and Technology ; Volume 16, Issue 10 , 2019 , Pages 6329-6346 ; 17351472 (ISSN) Nazari, P ; Rahman Setayesh, S ; Sharif University of Technology
    Center for Environmental and Energy Research and Studies  2019
    Abstract
    Abstract: The magnetite (Fe3O4) nanoparticles were synthesized and supported on the reduced graphene oxide. The characterization of the catalyst was performed by FT-IR, VSM, SEM, XRD, and BET techniques. The obtained results indicated that the in situ synthesis of Fe3O4 using coprecipitation method caused the homogenous formation of magnetite nanoparticles on the surface of reduced graphene oxide (average particle size ~ 71.032 nm) with high stability and catalytic activity toward electro-Fenton removal of Reactive Red 195. The effect of various factors (current intensity, initial pollutant concentration, catalyst weight, and pH) was evaluated by response surface methodology using central...