Sharif Digital Repository

Adsorption equilibrium data for CO, CO2, CH4 and C2H4 on 5A molecular sieve were obtained at (303, 373 and 573) K and at partial pressures up to 1000 kPa. An accurate and simple volumetric apparatus was used to measure gas sorption. The Langmuir and Sips equations were used to correlate the experimental data. In spite of the relative simplicity of both isotherms, the correlation between experimental and theoretical data is good. The Sips equation with three parameters has expected a better fit than the Langmuir isotherm with two parameters. Based upon the Langmuir equation the enthalpy of adsorption and pre-exponential factor in the van't Hoff correlation were derived for all four gases. ©... 

One of the most attractive features of Simulated Moving Beds (SMBs) is their ability to perform reaction and separation simultaneously in order to increase reaction yields. In this paper, an appropriate configuration for the operation of such systems in gas phase has been presented and to improve the separation efficiency, Pressure Swing Adsorption (PSA) is also employed. Fischer-Tropsch Synthesis (FTS) has been chosen to verify this idea. After preparing the catalyst, choosing appropriate adsorbent and constructing the necessary experimental set up, experiments have been performed to achieve maximum yield of desired products (i.e., ethylene and ethane). Effective variables, such as flow... 

In the present study, the effects of Sr and Mg were investigated on mechanical and biological properties of 58S bioactive glass (BG). SiO2-P2O5-CaO BG with different contents of Sr and Mg were synthesized via the sol-gel method and immersed in simulated body fluid (SBF) for several days to explore their biocompatibility. Precise analyses of the BG using X-ray powder diffraction, scanning electron microscopy, and transmission electron microscopy showed that the Mg-doped BG containing 8 wt % MgO possessed better biocompatibility. It was also found that mechanical properties of the BG could be improved by increasing the amounts of MgO and SrO. Both 5Sr-BG and 8Mg-BG samples did not exhibit any... 

The focus of this research is on the fabrication of aluminium-B4C and aluminium-ZrSiO4 composites by vortex method as a liquid phase process of metal matrix composites. SEM observations show that reinforcement particles are dispersed homogeneously throughout the aluminium matrix. Density, mechanical properties such as hardness and tensile strength of Al base MMCs containing different volume fractions (5, 10 and 15 %) of micro-reinforcements are examined separately and compared with those of monolithic aluminium. Results show that mechanical properties of samples are noticeably higher than those of the monolithic aluminium. The optimum amount of reinforcement in this... 

This article deals with product Family: a group of products with similar modules produced based on assembling to order (ATO) approach to cover diverse customer needs. The demand level and the customer requirements of these products are dynamically changing, which necessitate a novel model for co-reconfiguration of the product family (PF) and the supply chain (SC). Therefore, this article aims to apply Leader–follower Stackelberg Game Theory in order to present a co-reconfiguration of PF and SC based on three objectives: maximizing the total profit, maximizing customer utility and minimizing the supply chain cost in a bi-level structure. Maximizing the total profit and maximizing customer... 

Green products are increasingly considered by companies, owing to the significant attention of government regulations, customers’ requests and competitors. Here, we deal with Green Product Families (GPFs) by selecting green components, modules and products which are produced based on the assembling to order (ATO) approach to cover diverse customer needs. Designing a GPFs is important but not sufficient for sustainable optimization. In fact, we need to simultaneously consider the supply chain of a GPF to control the pollution generated in the downstream supply chain. For a sustainable optimization approach, this joint configuration is usually structured based on economic, environmental and... 

In the present work, the hot corrosion behavior of two types of multilayer plasma sprayed TBC were investigated and compared with functionally graded and conventional TBCs. These kinds of multilayer coatings consisted of nano/μ alumina as a top coat on YSZ layer, a metallic bond coat and a functionally graded intermediate layer deposited between YSZ and bond coat layers. All the layers were sprayed on the Ni-base super alloy substrate. The hot corrosion resistance of the plasma sprayed coatings was examined at 1050 °C for 40 h, using a fused mixture of 45 wt% Na2SO4 + 55wt%V2O5. Before and after hot corrosion, the microstructure and phase analysis of the coating were studied using scanning... 

The aim of this study is to investigate the effect of phosphate solution with Ca2+ additives on weight, surface morphology and electrochemical behavior of phosphated Zn-Ni film. In order to characterize structure and morphology of surface, X-ray diffraction (XRD) and scanning electron microscopy (SEM) were applied, respectively. Results showed that the main composition in produced coatings was hopeite Zn3(PO4)2·4H2O, which has high corrosion resistance. On one hand, in the presence of Ca2+ cations in solution, the weight of phosphate coating decreased, but on the other hand surface uniformity and corrosion resistance of the coating increased  

Ceramic-magnetic nanoparticles (CMNPs) are attracting attention due to their various applications, especially in biomedical industries. Among them, spinel ferrite CMNPs have received considerable deliberations among different spinel metal oxides due to their fascinating characteristics. Spinel ferrite CMNPs are used for enhancement of the applicability of CMNPs without affecting the intrinsic advantages of iron oxide CMNPs. Spinel ferrites with doping agents have useful electrical and magnetic properties in various fields. Moreover, the replacement of metallic atoms in ferrites is promising to manipulate physical characteristics and improve their performance. Among different spinel ferrites,... 

Using multiple antennas at the transmit and receive sides of a passive radar brings both the benefits of MIMO radar and passive radar. However one of the obstacles arisen in such configuration is the receive antennas placement in proper positions so that the radar performance is improved. Here we just consider the case of positioning one receiver among multiple illuminators of opportunity. Indeed it is a start for the solution of optimizing the geometry of the multiple receivers in a passive radar  

SbCl3 supported on montmorillonite K-10 is an efficient catalyst for the ring opening of epoxides with aromatic amines under solvent-free conditions and microwave irradiation to give the corresponding b-amino alcohols in high yields with high regioselectivity  

In this paper, we consider an integrated sensing and communication (ISAC) system with wireless power transfer (WPT) where an unmanned aerial vehicle (UAV)-based radar serves a group of energy-limited communication users in addition to its sensing functionality. In this architecture, the radar senses the environment in phase 1 (namely sensing phase) and mean-while, the communications users (nodes) harvest and store the energy from the radar transmit signal. The stored energy is then used for information transmission from the nodes to UAV in phase 2, i.e., uplink phase. Performance of the radar system depends on the transmit signal as well as the receive filter; the energy of the transmit... 

One of the important obstacles in MIMO (Multiple Input Multiple Output) radars is the issue of designing proper transmit signals. Indeed, the capability of signal design is a significant advantage in MIMO radars, through which, the system can achieve much better performance. Many different aspects of this performance improvement have been considered yet, and the transmit signals have been designed to attain such goal, e.g., getting higher SNR or better detector's performance at the receiver. However, an important tool for evaluating the radar's performance is its ambiguity function. In this paper, we consider the problem of transmit signal design, in order to optimize the ambiguity function... 

Two gains play key roles in recently developed MIMO wireless communication systems: "spatial diversity" gain and "spatial multiplexing" gain. The diversity gain refers to the capability to decrease the error rate of the MIMO channel, while the multiplexing gain implicitly refers to the amount of increase in the capacity of the MIMO channel. It has been shown that there is a fundamental tradeoff between these two types of gains, meaning interplay between increasing reliability (via an increase in the diversity gain) and increasing data rate (via an increase in the multiplexing gain). On the other hand, recently, MIMO radars have attracted much attention for their superior ability to enhance... 

It is a well known fact that using multiple antennas at transmit and receive sides improves the detection performance. However, in such multiple-input multiple-output (MIMO) configuration, proper positioning of transmitters and receivers is a big challenge that can have significant influence on the performance of the overall system. In addition, determining the power of each transmitter under a total power constraint is a problem that should be solved in order to enhance the performance and coverage of such a system. In this paper, we design the Neyman-Pearson detector under the Rayleigh scatter model and use it to introduce a criterion for the antenna placement at both transmit and receive... 

There has been much interest, recently, towards exploiting the Multiple-Input Multiple-Output (MIMO) technique in radar. It is shown that using multiple antennas at transmit and receive sides can improve the performance of the system. However, in order to analyze the system's performance, its ambiguity function, i.e. the ambiguity function of a MIMO radar, is needed to be defined. In this paper, beginning from the information theoretic definitions, we derive such function, specifically for a MIMO radar with widely separated antennas  

By combining the two ideas of MIMO (Multiple Input Multiple Output) and PCL (Passive Coherent Location) in radar, one can achieve the advantages of both recently developed techniques simultaneously. While using multiple antennas at the receive side provides a spatial diversity of the object to be detected, using multiple illuminators of opportunity, most importantly, makes the radar covert to the interceptors. One obstacle in such MIMO configuration is choosing the positions of the receive antennas. In this paper, after analyzing the Neyman-Pearson detector for the DVB-T based PCL, we introduce the probability of missed detection as a criterion to place the receive antenna. Here, we only... 

One of the most important obstacles in passive radar applications is removing the direct signal from the target channel. Otherwise, week echoes from the targets in the target channel would be ignored due to the limited dynamic range of the system. One of the most effective techniques in this field is using adaptive filters. In this paper various adaptive filters are introduced and their performances are shown and compared  

It has been shown that using multiple antennas in a radar system improves the performance considerably, since multiple target echoes are received from different aspect angles of the target. In this way, the target detection is improved. However, when using multiple antennas, some problems, such as designing the transmit signals, synchronization, etc. emerge that should be solved. One of such problems is the receiver placement. Receiver placement deals with choosing a proper position for the receive antenna in order to optimize the whole system's performance. In this paper, a receiver placement procedure based on improving the radar ambiguity function is proposed for the case of a multisite...