Sharif Digital Repository

Reliability analysis in engineering systems is one of important parts in design stage. Stress-Strength method is a method for reliability analysis in engineering systems. To obtain reliability, stress and strength distribution functions should be known, but these functions depend on design parameters and mostly these parameters are unknown. Usually obtaining exact stress and strength distributions is difficult and there is some uncertainty in distribution functions and their parameters. Also, weakness and uncertainty in data makes it difficult to calculate exact stress and strength distributions. In the case, when data is weak, results in point estimation methods (for example Maximum... 

The AASHTO Standard Specification defines diaphragms as a transverse member between girders in order to maintain sectional geometry. Some of the reasons in favor of using a diaphragm are that it prevents the girders from twisting during the process of construction and helps in distributing vertical live loads between girders and transfers lateral loads (wind or earthquake) to supports. It also provides restraint for the lateral-torsional buckling of the girders. While diaphragms at the ends of bridges are called end diaphragms, the diaphragms away from the bridge ends are called intermediate diaphragms. These members are usually made of steel or cast-in-place concrete. Based on their... 

Monitoring is of particular importance after impounding and during dam operation. In all large dams, by installation of the required instruments the pore pressure, soil mass pressure and displacement during construction, first impounding and operation are measured, then the performance of dam will be analyzed and evaluated. The aim of this study is to evaluate the performance of the "Gavoshan" dam, which has an important role on agriculture development and drinking water supply at west part of Country. To reach this, the values resulting from instruments have been implemented by FLAC software, using "Back Analysis" method. However, this assessment is complete when "back analysis" method is... 

Simultaneous localization and mapping (SLAM) is the action of detecting robot pose in an unknown environment and building the environment map by use of input data that captured from robot sensors. In visual SLAM, the input data for the robot, is limited to camera sensors. Nowadays, SLAM is one of the main challenges in robotic research.For autonomous action, we need robot pose in the map of the environment. The map production in the indoor environment, there is no GPS data, is one of the research issue in robotic community, in last decade. In this thesis, a new and efficient method is proposed for SLAM at the level of objects. The maps produced by state of the art methods don’t have a... 

When demand for a product is price sensitive, pricing and lot sizing decisions are interdependent. Similarly, when a product is highly perishable, the demand may need to be backlogged to avoid costs due to deterioration, i.e., perishability and backlogging are complementary conditions.In this thesis we stablish two economic production quantity models for deteriorating items under conditions of finite production, exponential decay and partial backordering and lost sale. Two joint pricing inventory control models are developed for the problem by employing different modeling approaches over an infinite planning horizon. In two models, customer is viewed to be impatient and the fraction of the... 

Oil/water separation is an important field, not only for scientific research, but also for environmental, economic, and social issues. On the one hand, oily wastewater, resulting from industries such as steel, aluminum, food, textile, leather, petrochemical and metal finishing, has become the most common pollutant all over the world. On the other hand, frequent oil spill accidents are of great concern since the discharge can lead not only to serious environmental pollution, but also a great loss of energy.
In crude oil removing water is necessary due to reducing corrosion, increasing thermal values of fuels obtained from crude oil, preventing catalists from destruction by water and... 

Breast cancer is the most common type of cancer in women and the second cause of death among them. The chance of successful treatment would be significantly increased if the disease is diagnosed at its early stages. There are numerous methods to diagnose breast cancer. One of the most important methods is positron emission mammography (PEM).The main aim of this study is to investigate the feasibility of improving PEM images by considering the time of flight corrections and the penetration depth of the rays in the crystals.In this study, a commercial PEM system, Naviscan PEM, is simulated using the GATE software. In the first phase of the study, two opposing planar detectors are used to study... 

Direct speech-to-speech translation, in which all compontents are trained jointly, is advantageous over cascaded approaches, because this method employs a simple yet effective pipeline to produce the outputs with a little inference time. Direct speech-to-speech translation models suffer from data scarcity issue, because they need parallel speech data in source and target languages. In this thesis, we present a novel direct speech-to-speech translation model to translate Persian speech to English, which is based on discrete speech units and uses a conformer-based encoder which is pretrained and a transformer-based causal decoder which uses relative position multi-head attention to do the task... 

In this study the behavior of buried pipes under permanent ground deformation (PGD) ef-fects caused by reverse faulting is investigated by means of both experimental and numeri-cal approaches. A total number of 7 full-scale experiments on buried steel pipes subjected to a fault offset of 0.6 m along the slip plane is carried out and the effects of different pa-rameters such as pipe diameter (114.3 mm (4ʺ) and 168.3 mm (6ʺ)), burial depth (0.25m, 0.5m, 1 m) and soil type (SW and SM) on the response of the buried pipes are studied. Ex-perimental results show that the pipe deformation shape changes with increasing burial depth from half-sine (for shallow depths) to an S-shape (for moderate to... 

So far, much research has been done on severe plastic deformation of aluminum alloy 2024, but there is limited information on the effect of artificial aging for this alloy in the supersaturated, post-MDF state. As one of the methods of extreme plastic deformation process, multidirectional forging process (single pass) has been performed on different alloys including aluminum alloy 2024 at ambient temperature. Alloy 2024 was subjected to solution treatment at 500°C for 1 hour and multi-directional forging process was immediately performed on it. Then, at temperatures of 100, 140, 190, 240, and 290 °C, the aging process was continued for one hour until artificial aging. In order to investigate... 

Platinum is one of the most used catalysts in refining and petrochemical industries. Also, Platinum uses in other industries like automobile catalytic convertor. As respect to importance of Platinum in these industries, growth of its consumption in recent decades and its very high price, recovery of Platinum is essential. Hence, many of various methods including hydro-metallurgy are applied. In despite of these wide spreading experimental investigations, due to low information about the reactions and the nature of reaction products, a few investigations were done on kinetics of Platinum recovery. A new method that used iodine solution to extract Platinum from spent reforming catalysts was... 

With growth in using the Internet and entrance of online stores and internet banks to daily people life, security has become a vital part of this new world. This causes, industrial companies started to produce security devices such as fire walls for protecting network from outside attackers and Intrusion Detection/Prevention Systems (IPS/IDS) for detection of attacks inside network. IPS/IDS causes network overload due to requiring copy of packet or flow information. With introducing Software Defined Networking (SDN) architecture, there is a hope to solve the issue with combining IPS/IDS and SDN features. Therefore, we propose two novel approaches for fast network scanning and SYN Flood...