The effects of pulse plating variables on morphology and corrosion behavior of Zn-Fe alloy coatings

, Article Journal of Coatings Technology Research ; Volume 9, Issue 2 , 2012 , Pages 215-218 ; 15470091 (ISSN) Roshanghias, A ; Heydarzadeh Sohi, M ; Sharif University of Technology

2012

Abstract

Considerable researches have been focused on zinc-iron (Zn-Fe) alloy coatings due to their superior characteristics among zinc alloy electrodeposits in recent years. The corrosion behavior of these coatings depends on the phase structure and morphology of the Zn-Fe deposits. In this work the effects of pulse plating variables such as current density, off-time, frequency and pulse modes on the morphology and phase structure of Zn-Fe deposits was studied by scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy dispersive spectrometry (EDS) analysis. The corrosion behavior of these coatings was measured by means of polarization curves and Neutral salt spray tests. It was shown...

The effects of functionally graded material structure on wear resistance and toughness of repaired weldments

, Article Materials and Design ; Volume 32, Issue 2 , February , 2011 , Pages 892-899 ; 02641275 (ISSN) Roshanghias, A ; Barzegari, M ; Kokabi, A. H ; Mirazizi, M ; Sharif University of Technology

2011

Abstract

To perform a long lasting, crack-free repair welding on ultrahigh strength steels, the filler metal must be chosen and applied properly. Avoiding several short-term repairs or replacements, the repaired weldment should reveal comparative characteristics such as wear resistance, toughness and hardness to base metal. In the present study, a novel functionally graded material have been introduced to obtain enhanced wear resistance and hardness at surface as well as improved fracture toughness at fusion line of repaired weldments. A comparative study of wear resistance of repaired weld metals has been carried out by pin-on-disk apparatus at 5N normal load and 0.14ms-1 sliding speed. Fracture...

Welding characteristics of ultrahigh strength steel in annealed and quench-tempered conditions

, Article Journal of Materials Engineering and Performance ; Volume 19, Issue 7 , 2010 , Pages 963-969 ; 10599495 (ISSN) Roshanghias, A ; Barzegari, M ; Kokabi, A. H ; Madaah Hosseini, H. R ; Sharif University of Technology

2010

Abstract

In this research, the welding characteristics of a new UHSLA steel, 35NiCrMoV123, have been studied in two general conditions (annealed and quench-tempered). Carbon equivalent value of 35NiCrMoV123 steel is near 0.9 which classifies it as a "very difficult to weld" steel. The effects of welding heat treatment cycle (preheat, interpass, and postheat) on metallurgical and mechanical properties of weldments have been investigated by tensile, impact toughness, and hardness tests, as well as optical microscopy observations. It has been observed that by employing high-temperature stress relief (600 °C), welding could be performed in annealed condition successfully. Also, the results indicate that...

Formation of intermetallic reaction layer and joining strength in nano-composite solder joint

, Article Journal of Materials Science: Materials in Electronics ; Volume 24, Issue 3 , 2013 , Pages 838-847 ; 09574522 (ISSN) Roshanghias, A ; Kokabi, A. H ; Miyashita, Y ; Mutoh, Y ; Madaah Hosseini, H. R ; Sharif University of Technology

2013

Abstract

In this study, the effects of CeO2 nanoparticle addition on tensile strength and formation of interfacial intermetallic compound layer for lead-free Sn-3.5Ag-0.7Cu solder joint were investigated. The results showed that the thickness of intermetallic layer was decreased with increasing weight percentages of CeO2 reinforcements, and the growth of the intermetallic layer was remarkably suppressed during isothermal aging at 150 C. It was also found that the tensile strength of the solder joint gradually increased with the addition of CeO2 particles, reached to the maximum value at 0.5 wt% CeO2 and then decreased drastically with further increase in CeO2 content. Microstructural investigation of...

Ceria reinforced nanocomposite solder foils fabricated by accumulative roll bonding process

, Article Journal of Materials Science: Materials in Electronics ; Volume 23, Issue 9 , September , 2012 , Pages 1698-1704 ; 09574522 (ISSN) Roshanghias, A ; Kokabi, A. H ; Miyashita, Y ; Mutoh, Y ; Rezayat, M ; Madaah Hosseini, H. R ; Sharif University of Technology

Springer 2012

Abstract

As one of the key technologies for high performance electronic devices, composite solders have been recently developed to improve thermal and mechanical properties of solder joints. In this study, accumulative roll bonding process was used as an effective alternative method for manufacturing high-strength, finely dispersed, void-free and highly uniform Sn-Ag-Cu/CeO 2 nanocomposite solders. Microstructural investigation of nanocomposite solders revealed that homogenous distribution of CeO 2 nanoparticle has been achieved and the eutectic as-cast morphology of the solder changed to recrystallized fine grained structure. As a result of severe plastic deformation during rolling, brittle and...

Design, Fabrication and Characterization of Lead-Free Nano-Composite Solder Sn-Ag-Cu/ CeO2

, Ph.D. Dissertation Sharif University of Technology Roshanghias, Ali (Author) ; Kokabi, Amir Hossein (Supervisor) ; Madaah Hosseini, Hamid Reza (Supervisor)

Abstract

As one of the key technologies for high performance electronic devices, composite solders have been recently developed to improve thermal and mechanical properties of solder joints. In this study, accumulative roll bonding (ARB) process was used as an effective alternative method for manufacturing high-strength, ﬁnely dispersed, void-free and highly uniform Sn-Ag-Cu/CeO2 nanocomposite solders. Microstructural investigation of nanocomposite solders revealed that homogenous distribution of CeO2 nanoparticle has been achieved and the eutectic as-cast morphology of the solder changed to recrystallized fine grained structure. As a result of severe plastic deformation during rolling, brittle and...

Nanoindentation creep behavior of nanocomposite Sn-Ag-Cu solders

, Article Journal of Electronic Materials ; Volume 41, Issue 8 , 2012 , Pages 2057-2064 ; 03615235 (ISSN) Roshanghias, A ; Kokabi, A. H ; Miyashita, Y ; Mutoh, Y ; Ihara, I ; Guan Fatt, R. G ; Madaah Hosseini, H. R ; Sharif University of Technology

2012

Abstract

High-density, ultrasmall-pitch electronic applications require miniaturized solder bumps with improved thermomechanical performance. In addition, novel techniques which are able to precisely characterize these solder bumps are needed. One approach to meeting both of these requirements is to make use of recently developed nanocomposite solders with enhanced creep resistance, and to characterize these solders using a nanoindentation technique. In the present study, the creep behavior of ceria-reinforced nanocomposite solder foils fabricated by the accumulative roll-bonding process was characterized using a depth-sensing nanoindentation technique. It was found that the creep resistance of the...

Technical English for mechanical engineers

, Book Alemi, Minoo ; Meghdari,Ali

Sharif University Press 2014

Abstract

Local educational institutions produce in-house English for Specific Purpose (ESP) materials according to the curriculum policies designated and developed by the Ministry of Higher Education In Iran. To this end, this book aims to be used in the Iranian setting at the tertiary level for undergraduate students majoring in Mechanical Engineering. Moreover, the style of English usage in this ESP textbook is American.
Regarding the content of the textbook, it has both thematic organizations in which the topics are relevant and includes sufficient treatment of the target language areas necessary for the students. The principle organizing approach of this textbook is theme-based. In addition,...

Feedback control of the neuro-musculoskeletal system in a forward dynamics simulation of stair locomotion [electronic resource]

, Article Proc. of IMechE Part H: Journal of Engineering in Medicine ; 2009, Vol. 223, No. 6, pp. 663-675 Journal of NeuroEngineering and Rehabilitation ; Volume 11, Issue 1, 30 April 2014, Article number 78 Selk Ghafari, A. (Ali) ; Meghdari, Ali ; Vossough, Gholam Reza ; Sharif University of Technology

Abstract

The aim of this study is to employ feedback control loops to provide a stable forward dynamics simulation of human movement under repeated position constraint conditions in the environment, particularly during stair climbing. A ten-degrees-of-freedom skeletal model containing 18 Hill-type musculotendon actuators per leg was employed to simulate the model in the sagittal plane. The postural tracking and obstacle avoidance were provided by the proportional—integral—derivative controller according to the modulation of the time rate change of the joint kinematics. The stability of the model was maintained by controlling the velocity of the body's centre of mass according to the desired centre of...

Design and Construction of a Soft Actuated Exoskeleton for Hand Rehabilitation of Stroke Patients

, M.Sc. Thesis Sharif University of Technology Razavi Zadehgan, Ali Akbar (Author) ; Ghafari, Ali (Supervisor) ; Meghdari, Ali (Supervisor)

Abstract

The main goal of this thesis is the design and development of a rehabilitation device for helping patients “to improve blood circulation” & retain and recover their abilities if possible that were lost during the stroke or a accident like that (my research in karaj/iran shows that it is possible by just movement of the specific body part). The focus is on hand in this thesis because Injuries to the hand are common and can be very debilitating since our hands are our primary means for interacting with our world. For rehabilitation in case of human hand there are several practices that should be done for patients either in home or in a rehabilitation center, time and money that is supposed to...

Silica chloride/wet SiO2 as a novel heterogeneous system for the deprotection of acetals under mild conditions [electronic resource]

, Article Phosphorus, Sulfur, and Silicon and the Related Elements ; Volume 178:2667-2670, Issue 12, 2003 Mirjalili, B. F. (BiBi Fatemeh) ; Pourjavadi, Ali ; Zolfigol, Mohammad Ali ; Bamoniri, Abdolhamid

Abstract

A combination of silica chloride and wet SiO2 was used as an effective deacetalizating agent for the conversion of acetals to their corresponding carbonyl derivatives under mild and heterogeneous condition

Earthquake Branch

, M.Sc. Thesis Sharif University of Technology Bagher Shemirani, Ali Reza (Author) ; Bakhshi, Ali (Supervisor)

Abstract

In the past few decades, shaking tables are widely used to evaluate system response of structures under seismic excitations. These devices are used without any fundamental research performed on a shaking table system as an entity model. In most of these studies for simplicity, it is assumed that there exist no considerable vibration and displacement around the shaking tables, and no attention is paid to the peripheral substances such as soil settled under the foundation.
In this thesis, result of ambient vibration test on shaking table system (solid deck, concrete foundation and soil layer) has been presented. Precise sensors known as low frequency and high accuracy accelerometers have...

Selective synthesis of conjugated enynes from α-arylalkynols using LiCl-Acidic Al2O3 under solvent-free conditions [electronic resource]

, Article Journal of Chemical Research ; Volume 2002, Number 8, 1 August 2002, pp. 378-380(3) Pourjavadi, A. (Ali) ; Bagheri Marandi, Gholam

Abstract

Free Content Selective synthesis of conjugated enynes from α-arylalkynols using LiCl-Acidic Al2O3 under solvent-free conditions

Selective preparation of fluorescent 1,8-naphthalimides using acidic alumina under microwave irradiation [electronic resource]

, Article Journal of Chemical Research ; 01/2001; 2001(11):485-487 Pourjavadi, A. (Ali) ; Bagheri Marandi, Gholam

Abstract

7H-benzimidazo[2,1-a]benz[de]isoquinolin-7-one compounds were prepared in a selective manner by reaction between o-phenylenediamines and appropriate 1,8-naphthalenedicarboxylic anhydrides using acidic alumina under microwave irradiation

Comparison between Performance of Stone Columns and RAPs from the Bearing Capacity and Settlement Reduction Viewpoints

, M.Sc. Thesis Sharif University of Technology Golestani Dariani, Ali Akbar (Author) ; Pak, Ali (Supervisor)

Abstract

Out of several ground improvement techniques available, stone columns have been widely used. This technique has been successfully applied to increase the bearing capacity and to reduce the settlement for foundation of structures like liquid storage tanks, earthen embankments, raft foundations, etc., where a relatively large settlement is permissible. This technique has, generally, been proven successful in increasing the stiffness of weak soils, upgrading their safe bearing capacity, and reducing their total and differential settlements, as well as speeding up their consolidation process. The beneficial effects of stone column installation in weak deposits is manifested in the form of...

Performance of Partially Filled Mini-Channels with Porous Media

, M.Sc. Thesis Sharif University of Technology Azimi, Adel (Author) ; Nouri, Ali (Supervisor) ; Moosavi, Ali (Co-Advisor)

Abstract

Laminar forced convection flow through a channel partially filled with a porous material was numerically studied in this thesis. The Navier-Stokes and Brinkman-Forchheimer equations were used to model the fluid flow in the free and porous regions, respectively. Coupling of the pressure and velocity fields was resolved using the SIMPLEC algorithm. The local thermal equilibrium was adopted in the energy equation. The effects of the thermal conductivity ratio, Darcy number, porosity, Reynolds number and height of the porous insert on velocity and temperature field were investigated. The results show that the flow behavior and its associated heat transfer are susceptible to the variation of the...

Improvement of Stability of Haptic Force Interaction with Virtual Environments Using a Haptic Interface with a Separate Tracker

, M.Sc. Thesis Sharif University of Technology Mashayekhi, Ahmad (Author) ; Meghdari, Ali (Supervisor) ; Nahvi, Ali (Supervisor)

Abstract

In the present study, a new version of haptic devices is presented in which user’s hand is in contact with the device just while collision with virtual surface. In this system, the position of user’s finger can be traced by using a camera and the haptic device follows user’s finger at the distance of about two centimeters. While the haptic device approaches to the virtual surface, gradually reduces its speed and stops about two centimeters distant of virtual plane. Then user’s hand collides with the haptic device which is static. Greater fidelity, transparency, more stability and also no need to large actuators are of the advantages of this system. In this project, first we present a new...

Simulation of the Biomolecule Imaging and Manipulation Via AFM by Molecular Dynamics Method

, M.Sc. Thesis Sharif University of Technology Kheiroddin, Mohsen (Author) ; Meghdari, Ali (Supervisor) ; Moosavi, Ali (Supervisor)

Abstract

In this thesis we try to find optimized parameters for imaging and manipulation of a biosample with AFM. For this we have prepared a numerous Molecular Dynamics simulation and find some reliable result. So, first we have focused on imaging process in Non contact mode (the less harmful mode). Then we headed into the manipulation process. The main problem about manipulating a biosample is the environment. In imaging section, the process of imaging a biomolecule by AFM is modeled using molecular dynamics simulations. Since the large normal force exerted by the tip on the biosample in contact and tapping modes may damage the sample structure and produce irreversible deformation, the non-contact...

Characterzing Variation of Small Strain Shear Modulus of Unsaturated Sand During Hydraulic Hysteresis with Bender Elements

, M.Sc. Thesis Sharif University of Technology Shahbazan, Parisa (Author) ; Pak, Ali (Supervisor) ; Khosravi, Ali (Supervisor)

Abstract

Results of previous studies on silt and clay indicated that variations in the small strain shear modulus, Gmax, during drying had a non-linear increasing trend with matric suction with greater values upon wetting. However, due to different material properties and inter-particle forces, different behaviour in Gmax is expected for sand. Although considerable research has been devoted in recent years to characterize the behaviour of Gmax of sand during drying, rather less attention has been paid to the effect of hydraulic hysteresis on Gmax and its variations during wetting. In the study presented herein, an effort was made to characterize the variation of Gmax for specimens of sand during...

Sequential Competitive Facility Location In Continuous Geometric Space

, M.Sc. Thesis Sharif University of Technology Lavasani, Ali Mohammad (Author) ; Abam, Mohammad Ali (Supervisor)

Abstract

Abstract The problem of competetive facility location can be defined as follows: There are a number of customers in the form of points in space, and two players arrange a number of facilities in the form of points in space, given some limitations, respectively. Each customer’s connection to each facility has a cost for the customer and an advantage for the facility, and each customer wants to be connected to at most one of the facilities which has the lowest cost for him. The goal is to find the strategy of placing the facilities and determining the cost which the facility receives from the customer, in such a way that the player’s profit is maximised.In this thesis, we first sought to...