Sharif Digital Repository

Cache memory is one of the most important parts of the microprocessors. Caches improve performance by bringing data and instructions near the processors and decreasing the access time to data and instructions. But caches are also vulnerable to some kind of error called soft error. When an error happens in a cache, suddenly can propagate throughout the system and affect the integrity and reliability of the overall system. There are actually two types of errors in cache memories, permanent (hard) errors and transient (soft) errors. Previous studies have shown that about 92% of system reboots are initiated by soft-error occurring in cache memory. Soft-errors have two main sources, alpha... 

In the present study, the numerical simulation of incompressible laminar and turbulent flows using a high-order finite difference lattice Boltzmann method is presented. To handle curved geometries with non uniform grids, the incompressible form of lattice Boltzmann equation is transformed into the generalized curvilinear coordinates and the spatial derivatives of the resulting equation are discretized using the fifth-order WENO scheme. The advantage of using the WENO-LBM developed is that it needs less number of grid points and remains stable even at high Reynolds number flows. For the temporal term, the fourth-order explicit Rung-Kutta scheme is adopted for laminar flow calculations and... 

Reducing noise, vibration and damage to the vehicle's passenger compartment was always a problem that has been investigatedin many researches. Here engine mounts as connecting members between engine and chassis play a big role. Because both of engine and road vibration put on it. Many studies have been done to optimize the engine mounts. As a result, many of hydraulic engine mounts with different variety of system control. But a few researches did about optimization of location and orientation of engine mounts. Therefore this project is to provide a process to optimize the location and orientation of engine mounts. The optimization process is First the dynamic equations of dynamic system are... 

Unmanned Aerial Vehicles have been used for different applications despite their short life. In last recent years, the developements in technology which leads to producing smaller electronical and electromechanical deveices, attract more attention to the researches in these fields. Among these vehicles, unmanned helicopters are more important because of their special abilities and capabilities. However there are some drawbacks which makes using them more difficult.
In this project, the first principle modeling of a RC helicopter has been accomplished and a parametric model including different sections effects has been created. This model has been implemented for a Trex600 CF helicopter.... 

In recent years health monitoring and prognostics of complex systems have been considered more than ever.. In the present researh, data - based approach has been selected among various prognostics and health monitoring approaches. One of the most challenging issues in data-based methods is how to map system sensor information to its health status. In this research, different methods of mapping are discussed. The results show that sensor fusion by principal component analysis (PCA) offers acceptable performance. This pattern produces a single-dimensional signal for health monitoring with high reliability.The second challenge is to predict the status and design of the prognostics module. For... 

Multiscale modeling is performed within the framework of homogenization methods for problems in which the scales are separated. The existence of representative volume element (RVE) is one of the main ingredients of homogenization methods. Due to non-existence of RVE and macroscale mesh sensitivity, the continuous homogenization method is not applicable for softening materials. Despite the non-existence of RVE for softening materials, it has been demonstrated that by performing the average over the active damage zone rather than the entire domain, objective responses with respect to RVE size could be obtained. That is why discontinuous homogenization is used instead of continuous... 

Nowadays, hybrid electric vehicles get more attention, not only for decreasing fossil fuel resources, but also for increasing environmental pollution. Using multi-propulsion system in hybrid vehicles causes, the low efficient performance of combustion engine is reduced compare to conventional vehicles. Fuel consumption and pollution that reduced in hybrid vehicles is related to how the multi-propulsion system works. Some researches that have been done about hybrid control algorithms, are completely software modeling and development. Despite importance of these researches in development and evaluation of power distribution algorithms, hardware-based evaluations are also necessary. In all... 

One of the most important unit operations in the production of dry powder biological products involves a freeze dryer apparatus. In this process, Liqueur, which is containing the α-amylase enzyme, undergoes a frigidity condition in which loses its moisture during sublimation. Under these circumstances, applying an adequate supply of sublimation enthalpy without raising the temperature of the frigid material up to melting, plays an important role in the quality of the product and preventing degradation of the α-amylase enzyme. Freeze drying depends on two main factors; time and energy. Furthermore, it is necessary to obtain an optimal temperature and pressure for different steps and... 

The main objective of this project is to take the first step in designing torsional vibration damper (TVD) for engines in Iran. To this end a complete dynamic model of a 4 cylinder internal combustion engine comprising of all reciprocating parts plus the crankshaft was developed using Bond Graph method. Real firing data of the engine was used as input to the system and output torque to gearbox shaft as the output. The system equations in two cases, with TVD and without TVD were derived. MATLAB software was used to solve these equations in finding the quality of performance of the torsional vibration damper. Dynamic properties of crankshaft and designed TVD were obtained using finite element... 

Gearbox is one of the important components of power transmission chain in the car which the engagement of the gears inside it causes noise. The following thesis, is in line with the project that was defined as "NVH reduction of the Tiba X200 gearbox" and to increase the correlation between university and industry, the aim of which was to improve all the noise sources in the mentioned vehicle. The purpose of this project is to reduce the noise of the gearbox shell by using reinforcing blades called ribs. For this purpose, first the desired changes were made in Solidworks software on the 3D model of the gearbox shell, and then the finite element model of the gearbox shell was prepared in... 

The low female labor force participation rate in the Iranian labor market relative to the global average and even to countries that do not differ significantly from the socio-economic characteristics of our country is one of the important questions of the Iranian labor market. In this study, we seek to answer the question of whether the economic participation rate of married women will increase if the gender gaps in wages, job findings and job losses among women and men are eliminated in the Iranian labor market. To answer this question using household expenditure and income data and labor force data, we show that between the two categories of occupations, in terms of the share of women's... 

With the environmental concerns and scarce supply of the crude oil, a revival in the development of bio-based and compostable materials is coming. They are in general being called the ''green'' materials, among which poly(lactic acid) (PLA) got the most extensive attention due to its good combined properties, including the renewable feedstock, the compostability, and its good mechanical properties, especially the young's modulus and stiffness. PLA has found numerous applications. It is considered having the highest potential to replace some regular petroleum based plastics. However PLA has its own shortcomings, its brittleness, low heat distortion temperature and relatively high cost witch... 

Due to the excessive failures of tires used on mining trucks, which lead to significant economic and environmental damages, mine operators are seeking replacements for them. The ASW mechanical wheel, introduced by the American company Global Air Cylinder Wheel, is recognized as the most well-known alternative to pneumatic tires for mining trucks. Although this company has been active since 2004, it has not yet released a commercial product. This study examines the structural, behavioral, and operational characteristics of the mechanical wheel and its impact on the performance of mining trucks. The structure of the mechanical wheel consists of a set of hydro-pneumatic actuators that connect a... 

Fatigue crack growth can have harmful effects on the reliability rotary machine. While an early warning to crack, can be used to extend the life of these expensive machines and increase reliability.Structural Vibration Condition Monitoring as a primary fault detection method, achieved to a lot amazing result and for this reason studies vibration behavior of cracked rotational shaft is a big issue for engineers of dynamic machine.In this research, first check the fault detection methods based on structural vibration condition monitoring, mode shape methods were extracted. Then by modeling rotational shaft in computer and creation of crack on it, fault detection quality of these methods have... 

It is important to provide an appropriate and economically method with technical and engineering considerations to stabilize excavated underground spaces. The necessity of this, especially for the construction of underground metro stations located in the cities which faces many problems, is more evident. In this research, it has been tried to introduce an optimal method according to the type of area for the construction of the underground station. In order to obtain stress and strain condition in structural elements and surface deformations due to different stages of excavating, numerical modeling in FLAC3D has been used. By examining the parameters that affect the sustainability of this... 

In the present study, the effects of increasing the value of shale gas production, either due to increased production or price increases, have been studied on economic variables such as employment, wage, property value and the number of births. In this regard, the data for each of these variables was used at the county level in the United States of America between 2000 and 2011. In order to estimate the desired effects, counties are divided into two types of boom and non-boom counties. The findings indicate that increasing natural gas production will lead to more employment and wage growth in boom counties than non-boom counties. Also, during the period of increasing production, the value of... 

Co-movement between inflation and nominal interest in response to an interest rate shock, dubbed neo-fisherianism, has been the subject of contentious debate since the advent of non-inflationary ZLB environment. We design an economic model rich with banking features to understand the economic responses to permanent and long-term interest rate shocks. We find that responses to a permanent positive interest rate shock depend on the monetary authorities’ speculation of the new long-term inflation rate, with the most probable outcome being a permanent increase in inflation. Responses to a long-term positive interest rate shock depict an increase and then decrease in inflation. We also discover... 

In this study, we aim to learn representations from microscopic cell images that effectively capture the features of drugs affecting the cells, allowing us to identify effective drugs for treating a disease. We employ two parallel learning paths using predictive and generative models. Specifically, we have achieved a predictive model on the RxRx19a dataset that, unlike previous models, is interpretable, optimized, and robust to dras- tic changes in drug properties. Additionally, we have developed the first generative model on this dataset, which not only generates high-quality images but also discovers a meaningful latent space. This latent space divides the representation into relevant...