Sharif Digital Repository

The effect of ihe asymmetric water entry over a submerged part of a ship on the hydrodynamic impact is investigated numerically. A wedge body is considered 10 study and the problem is assumed to be two-dimensional. The Results of symmetric and asymmetric impacts are compared together. The effect is found significant in the numerical simulation. The maximum hydrodynamic pressure at a heel angle of 10 degrees becomes about 95% more than that of the symmetric entry. The result of the present, work proves the importance of asymmetrical hydrodynamic impact leading for structural design of a ship. Besides, the numerical procedure is not limited to a wedge type cross section and it is possible to... 

These days, tourist submarine industry has become of increasing interest and prosperity. A tourist submarine operating beneath a seaway suffers different undesired motions which may cause difficulty in operability for the vehicle and habitability of its passengers. From this point of view, this paper studies the hydrodynamic problem of submarine operability in waves. In this investigation strip theory has been used and effects of different parameters of sea state, sea direction, depth, speed and duration of operation have been considered. Results of presented case study indicate that speed effect is insignificant while the operating depth role seems more important  

The present study is concerned with the numerical simulation of free-surface waves and wave induced separation in the presence of an intrusion. The results of several simulations are reported. The first study was performed for a NACA0024 surface piercing hydrofoil over a range of several Froude numbers (0.19, 0.37, 0.55), along with wave breaking at Fr = 1.0 The NACA0024 foil was of particular interest, as it almost has no separation at large depths; thus the effect of the free-surface wave and the wave induced separation could be studied. Free- surface waves and wave induced separation results were evaluated and compared with both the available experimental data and the previous numerical... 

Micro motion stages are one of the essential components in field of micro robotics and ultra fine positioning systems. This research presents the optimum design of a 3-DOF micro motion stage and its position control using FEM simulation. This stage to be studied uses a 3 RRR flexure hinge base compliant mechanism driven by three piezoelectric stack actuators to provide micro scale planar motion. First of all parametric modeling of the stage will be fulfilled in ANSYS environment utilizing a commercial piezostack and different types of flexure hinges. Hence the Jacobian matrix will be achieved for each case. The optimum selection of the hinge form will be achieved upon results of the previous... 

The chaotic dynamics of roto-translatory motion of a triaxial Kelvin-type gyrostat satellite under gravity gradient perturbations is considered. The Hamiltonian approach is used for modelling of the coupled spin-orbit equations of motion. The complex Hamiltonian of the system is reduced via the extended Deprit canonical transformation using the Serret- Andoyer variables. Therefore, this reduction leads to the derivation of the perturbation form of the Hamiltonian that can be used in the Ricci curvature criterion based on the Riemannian manifold geometry for the analysis of chaos phenomenon. The results obtained from Ricci method as well as the values from the Lyapunov exponent demonstrate... 

IT Governance provides a business focus to enable alignment between business and IT objectives at high level COBIT framework and focused on IT operational levels, ITIL standard. COBIT and ITIL are not mutually exclusive and can be combined to provide a powerful IT governance, control and best-practice framework in IT service management. So ITIL business-IT strategic alignment perspective could be improved using COBIT framework. Focusing on COBIT processes which support (primarily and secondarily) strategic alignment, in this paper, first, we map COBIT 4.1 to ITIL v3 to identify how ITIL cover COBIT control objectives. Furthermore, based on control objectives which are not completely... 

Quasi-periodic and chaotic behavior, along with the control of chaos for a Gyrostat satellite (GS), is investigated in this work. The quaternion-based dynamical model of the GS is first derived, and then the influences of the reaction wheels in the GS structure, under the gravity gradient perturbation that causes a route to chaos through quasi-periodicity mechanism, is investigated. For the suppression of chaos in the system, a chaos control system with the quaternion feedback is designed for the GS based on the extension of the Ott-Grebogi-Yorke (OGY) method using the linearization of the Poincaré map. In the extended OGY controller, the Poincaré map is estimated using the Least Square... 

This article presents a study on the capability of the time domain OMA method, NExT-ERA, to identify closely spaced structural dynamic modes. A survey in the literature reveals that few experimental studies have been conducted on the effectiveness of the NExT-ERA methodology in case of closely spaced modes specifically. In this paper we present the formulation for NExT-ERA. This formulation is then implemented in an algorithm and a code, developed in house to identify the modal parameters of different systems using their generated time history data. Some numerical models are firstly investigated to validate the code. Two different case studies involving a plate with closely spaced modes and... 

Micro motion stages are one of the essential components in field of micro robotics and ultra fine positioning systems. This research presents the optimum design of a 3-DOF micro motion stage and its position control using FEM simulation. This stage to be studied uses a 3 RRR flexure hinge base compliant mechanism driven by three piezoelectric stack actuators to provide micro scale planar motion. First of all parametric modeling of the stage will be fulfilled in ANSYS environment utilizing a commercial piezostack and different types of flexure hinges. Hence the Jacobian matrix will be achieved for each case. The optimum selection of the hinge form will be achieved upon results of the previous... 

Vivid banding pattern of the chromosome image is a crucial part for diagnosis in karyotype medical test. Furthermore, thriving computer aided segmentation and classification depend on the initial image quality. In this paper, we propose an adaptive and iterative histogram matching algorithm for chromosome contrast enhancement especially in banding patterns which is one of the most important information laid in chromosome image. Objective histogram, with which the initial image needs to be matched, is created based on processes on the initial image histogram. Calculation of statistical moments of image histogram and determination of parameters in each step of iteration based on these moments... 

Vivid banding patterns in medical images of chromosomes are a vital feature for karyotyping and chromosome classification. The chromosome image quality may be degraded by many phenomenon such as staining, sample defectness and imaging conditions. Thus, an image enhancement processing algorithm is needed before classification of chromosomes. In this paper, we propose an adaptive and iterative histogram matching (AIHM) algorithm for chromosome contrast enhancement especially in banding patterns. The reference histogram, with which the initial image needs to be matched, is created based on some processes on the initial image histogram. Usage of raw information in the histogram of initial image... 

The present study tries to use the methanol-silver nanofluid filled thermosyphon heat exchanger and compares the effectiveness as well as energy saving with pure methanol. Experimental results show that using methanol-silver nanofluid, leads to energy saving around 8.8-31.5% for cooling and 18-100% for reheating the supply air stream in an air conditioning system  

Most of the publications regarding the maxim covering location problem (MCLP) address the case where the decision is to be made for one period. In this paper, we deal with a rather untouched version of MCLP which is called dynamic MCLP (DMCLP). In order to solve this problem, a simulated annealing (SA) has been presented. The proposed solution algorithm is capable of solving problems with up to 2500 demand nodes and 200 potential facilities with a fair amount of exactness. Our experiments showed that the proposed approach finds solutions with errors less than one percent  

In the present study, alginate/cartilage extracellular matrix (ECM)-based injectable hydrogel was developed incorporated with silk fibroin nanofibers (SFN) for cartilage tissue engineering. The in situ forming hydrogels were composed of different ionic crosslinked alginate concentrations with 1% w/v enzymatically crosslinked phenolized cartilage ECM, resulting in an interpenetrating polymer network (IPN). The response surface methodology (RSM) approach was applied to optimize IPN hydrogel's mechanical properties by varying alginate and SFN concentrations. The results demonstrated that upon increasing the alginate concentration, the compression modulus improved. The SFN concentration was... 

Equal channel angular pressing is an outstanding method for imposing large plastic deformation to metallic materials without any decreasing in cross section area of as processed samples. In this paper, the effect of working temperature, ram speed and the number of passes on the formation of adiabatic shear bands in Al6061 during equal channel angular pressing was investigated. Billets of the alloy were processed up to four passes via route BC from room temperature to 200°C with two ram speeds using a die that imparts an effective strain of ∼1.1 per pass. The results have demonstrated that the onset of the adiabatic shear banding in this alloy strongly depends on the ram speed: more... 

The Newsboy problem has always been an important issue in inventory management. The multi-product newsboy problem with random yield and budget constraint named as the Gardener Problem is one of the novels and popular extensions of the newsboy problem. Different from the existing studies, this paper presents a multi-product gardener problem with reservation policy. Moreover, a discount rate is offered to those customers who are willing to make reservations. In addition to the demand from the original customers, extra demand is included in the model due to the motivation received by the discount rate. A solution algorithm namely the multi-product gardener problem with reservation policy... 

The quasi-static and strain-controlled fatigue characteristics of ZK60 extrusion have been investigated along three different directions: the extrusion direction (ED), the radial direction (RD), and 45° to the extrusion direction (45°). The quasi-static response showed symmetric behavior for the samples tested along RD and 45° whereas the ED samples manifested completely asymmetric behavior. Although the ED samples exhibited longer fatigue lives than the RD and 45° in the high cycle fatigue, the fatigue lives in the low cycle fatigue regime were similar. The texture measurement indicated a sharp basal texture along ED, explaining its asymmetric behavior. Higher tensile mean stress and less... 

Simultaneous reductions in inventory of raw materials, work-in-process, and finished items have recently become a major focus in supply chain management. Vendor-managed inventory is a well-known practice in supply chain collaborations, in which manufacturer manages inventory at the retailer and decides about the time and replenishment. In this paper, an integrated vendor-managed inventory model is presented for a two-level supply chain structured as a single capacitated manufacturer at the first level and multiple retailers at the second level. Manufacturer produces different products where demands are assumed decreasing functions of retail prices. In this chain, both the manufacturer and... 

Using flake powder metallurgy (FPM) technique, combined with high pressure torsion, super high strength-ductile Cu-CNT nanocomposite with high electrical conductivity is developed. The nanocomposite with 4 vol% CNT showed high tensile strength of ~474 MPa, high electrical conductivity of ~82.5% IACS as well as appreciable ductility of ~11%. According to microstructural studies, the excellent properties of the nanocomposite are attributed to the formation of trimodal grains, high density of twin and low angle grain boundaries, improvement in CNT and Cu interfacial bonding, and appropriate distribution and maintaining the microstructure of the nanotubes in the production process. The results... 

Malaysian secondary schools are facing a shortage of male teachers. Almost 70% of the teaching profession is dominated by female teachers. There is an obvious gap in the reason why teaching is not preferred by the male gender. This study intends to find the determinants of career success among male teachers with the hope of revealing the career success factors that are associated with male teachers. A survey was done among 140 male teachers in secondary schools in the state of Malacca, Malaysia. Results showed that 4out of 5 of the determinants factors are significantly explaining career success among the teachers (Emotional Intelligence, Person-Job-Fit, Career Adaptability & Work-Life...