Sharif Digital Repository

Phase shifters are commonly used in the implementation of phased-array antenna systems.The function of these systems is highly dependent on the performance of phase shifters. In addition, phase shifter circuits are used in some applications such as antenna test and regulation, power amplifier linearization, and QAM modulator implementation, to name but a handful. In this project, design of phase shifter blocks, as well as limitations of fabrication on silicon substrate, is studied and these blocks are designed for maximum bandwidth and minimum sensitivity based on fabrication characteristics and environmental conditions. Design of a 6-bit phase shifter based on vector-sum method is the... 

One of the most important parameters of implanted chip in body is its ability to work for a long time without the need for battery change. Hence designing radio frequency transceivers used in these chips should be done with the lowest possible power consumption. Of course it should be noticed that for correct communication, standard specifications must be meeted. In this thesis, a receiver in medical implant communication service standard with the goal of minimal power consumption is designed. In circuit design different challenges such as low inductor quality factor, threshold voltage of transistors and usual trade-offs between receiver parameters are faced. Therefore, previous used... 

A key point in designing class-C oscillators is maximizing the Figure-of-Merit (FoM). For this purpose, changing the oscillator’s structure or adjusting its bias current may be used. Previous literatures mostly limit their efforts to the first case, leaving the issue of determining the proper bias current almost untouched. In this work, a new approach recruiting DC voltage of the common source node of the switching pair transistors as an indicator has been presented. Using theoretical analysis, it has been shown that maximizing this voltage will optimize the oscillator in term of the FoM. The proposed indicator has the advantages of not introducing any loading effect to the output node, and... 

The telecommunication manhole is a place that the cables of the telephone network are located on it. line Inside these manholes, there are equipment and cables for telephone. The number of these places is many, so protection and maintenance of the manholes have been problematic in case of theft of the cap, equipment inside them and flooding. Also, lack of inspection officers and the high cost of repairing and replacing parts inside them, has made it difficult for telecom companies to handle these problems. The only way to connect the manhole is a telephone line inside them. Also, there is no proper electrical power inside the manhole, so the design and implementation of a system that... 

Frequency synthesizers are one of the most critical building blocks of RF systems. Their task is to produce high-frequency precise and stable clock signals from a low-frequency source. The signal used in mixers to up-convert and down-convert desired signals in transceivers and the precise clock of analog to digital converters are made by frequency synthesizers. Designing frequency synthesizer, because of its lots of parameter and dependency of these parameters to each other, is a hard task which forces designers to propose new structures. In this thesis, an integer-N frequency synthesizer for Bluetooth application, with the goals of decreasing spurious tones power and settling time, is... 

The Emergence of modern wireless communication standards and the need to use the frequency spectrum efficiently has made communication system designers exert complex modulation schemes. One of the results of such designs that has a direct impact on the design procedure of power amplifiers is that there will be signals with high peak to average power ratio.The obvious consequence of this manner in the design of communication systems would be the reduction of power amplifier efficiency due to its operation in its back-off region. The solution will be to use load modulated power amplifiers such as Doherty amplifier which brings up the problem of limited bandwidth.In this thesis, we tackle this... 

The wideband code-division multiple access (WCDMA) system has been widely used for the third-generation wireless communication system. It uses Frequency division duplexing for two-way communication by a transceiver. Although a duplexer will significantly suppress the TX leakage signal (50dB-60dB), a residual attenuated signal still remains at the receiver input and act as a strong blocker which reduces the sensitivity of the receiver. For reducing the effect of the TX leakage on the RX performance, a band pass RF SAW filter is typically inserted between the LNA and the mixer to reject the TX leakage. However, this filter increases the system cost and size. This encouraged us to propose a novel... 

Transistors’ miniaturization and advent of short-channel effects causes searching for another devices with least adverse characteristics in short channels. Among all the considered devices, monolayer transistors attracted the attention. Although most of the papers in literature focused on the physical phenomenon of the device, circuit design of these transistors have been overlooked. Most of the papers related to monolayer transistors did not explain the design methodology of their circuits and they confined their work just to the report of the circuits constructed with 2D-based transistors. In order to take advantage of 2D materials in electronic circuits, simple modelling for... 

Efficient radio frequency (RF) power amplifiers (PAs) are critical in portable battery-operated wireless communication systems because they can dominate the power consumption. Linear amplifiers are enough linear but suffer from poor efficiency. On the other hand, switching power amplifier are efficient but are nonlinear and just amplify constant envelope signals. Two conventional methods for increasing transmitter efficiency and linearity are envelope elimination and restoration (EER) and envelope tracking (ET). In both methods, supply modulator controls RF power amplifier supply based on the signal envelope. Efficiency and bandwidth are critical factors in supply modulator. Thus hybrid... 

Various safety systems have been designed and developed in recent decades, but one of the most important issues is the improvement of safety of such systems and that is the goal of this research. In this thesis, while introducing different methods of designing an electronic system, we designed one of these safety systems: the Airbag system in accordance with ISO 26262 by considering standard requirements, prediction of potential hazards of the system, and its safe design at the system level. The designed system is capable of detecting the car crash in a precise and timely maner. The airbag will deploy within 45 milliseconds protecting the health and safety of occupants of the car and in... 

Wireless Power and Data Transfer (WPDT) is a major part of a biomedical implant system. Maximiazing the Power Transfer Efficiency (PTE) and maximizing the data rate are the main challenges in WPDT. In a conventional biomedical implant system, a single inductive link is used to transfer both power and data from outside the body to inside. Data is transmitted by modulating one of the carrier signal properties, i.e., amplitude, frequency or phase. While being simple and robust, this method suffers from the fundamental trade-off between the PTE and data rate. To address this issue, various methods have been proposed including multiple carriers and multiple inductive links, and inductive link... 

The development of natural gas supply systems and its transmission networks are vitally important to achieve a natural gas economy. Development and planning of natural gas transmission networks as multidisciplinary projects have crucial impact on the economy of gas-rich countries like Iran. The nvestment costs and operation expenses of pipeline networks are so large that even small improvements in system utilization and planning can involve substantial amounts of money. A large number of technological options exist for development in conversion, distribution levels and …, which cause various pathways for supplying natural gas. In addition there are many energy recovery technologies along... 

One of the most important parameters of an implanted device in the human body is its ability to operate for a long time to decrease the need for surgery in order to replace the battery. Therefore, the radio transceivers in these devices are designed in such a way to reduce the power consumption as much as possible. But, at the same time, it is crucial that the bit error rate be as small as possible to decrease the number of incorrect sent and received bits. Thus, the phase noise should also be as small as possible in order to reduce the bit error rate. In this thesis, a transmitter has been designed for Medical Implant Communications Service standard. In order to reduce the power... 

The airport terminal is difficult to plan and design due to the different components and the intricate complexity of its parts. At the airport terminal, we face a queue system which simulation is always a good way to analyze. In addition, computer simulation using modern softwares with the capability to model different types of systems, including the airport terminal, while being less realistic than analytical models, is less costly than operational Exercise.In this study, a supportive approach for better and specific management of Iranian airport terminal buildings with discrete-event simulation is proposed, considering the need for managing the airport terminals building in the country and...