Sharif Digital Repository

The control of texture and microstructure can be achieved by an appropriate thermomechanical treatment in industrial production. The effects of finish rolling temperature, cold reduction and annealing temperature on texture development and microstructure in Brass sheet were investigated. The role of deformation inhomogeneities on texture evolution has been considered. The formation of transition bands during hot rolling enforced the intensity of cube components. Shear bands increased the intensities of S and Cu components after cold rolling and at higher cold reductions. Transition from Cu to Y and Y to Bs was completed better because of mechanical twinning. Thermal twins annihilated the... 

Dust deposition on the surface of solar systems is one of the main parameters that significantly affects the performance of such systems. In this study, the effect of dust deposition density on the performance of photovoltaic modules (PV) and photovoltaic-thermal systems (PVT) is numerically investigated. Accordingly, all layers of a monocrystalline silicon PV module for both systems are simulated. Moreover, the effect of various system parameters on the performance of both clean and dusty PV module and PVT system are studied. The studied parameters included: solar radiation intensity, ambient temperature, coolant inlet temperature, and coolant inlet velocity. The obtained results indicate... 

In this study, the performance of a Photovoltaic Thermal-Organic Rankine Cycle (PVT-ORC) system combined with a Proton Exchange Membrane Electrolysis Cell (PEMEC) is investigated. A combined numerical/theoretical model of the system is developed and used to evaluate the effect of various system design parameters. In addition, the effects of using water, ethylene glycol, and a mixture of water and ethylene glycol (50/50) as the working fluid of the PVT system and R134a, R410a, and R407c as the working fluid of the ORC cycle on the performance of the PVT-ORC-PEMEC system are studied. Based on the results, R134a and water demonstrated the best performance as the working fluid of the ORC and PVT... 

As one of the cleanest energies, hydrogen has attracted much attention over the past decade. Hydrogen can be produced using water electrolysis in a Proton Exchange Membrane Electrolysis Cell (PEMEC). In the present study, the performance of the PEMEC, powered by the Photovoltaic-Thermal (PVT) system, is scrutinized. It is considered that the PVT system provides the required electrical power of the PEMEC and preheats the feedwater. A comprehensive numerical model of the coupled PVT-PEMEC system is developed. The model is used to investigate the effect of various operating parameters, including solar radiation intensity, inlet feedwater temperature, and feedwater mass flow rate, on the... 

As one of the cleanest energies, hydrogen has attracted much attention over the past decade. Hydrogen can be produced using water electrolysis in a Proton Exchange Membrane Electrolysis Cell (PEMEC). In the present study, the performance of the PEMEC, powered by the Photovoltaic-Thermal (PVT) system, is scrutinized. It is considered that the PVT system provides the required electrical power of the PEMEC and preheats the feedwater. A comprehensive numerical model of the coupled PVT-PEMEC system is developed. The model is used to investigate the effect of various operating parameters, including solar radiation intensity, inlet feedwater temperature, and feedwater mass flow rate, on the... 

In this work, a three-dimensional numerical model is developed to investigate the performance of a photovoltaic thermal system integrated with a thermoelectric generator module (PVT/TE). Furthermore, the effects of various operating parameters such as solar radiation, coolant mass flow rate, and inlet and ambient temperatures on the performance of both the PVT and PVT/TE systems are investigated and compared. Based on the obtained results, the electrical efficiency of the PVT/TE system, when exposed to solar radiation of 600 and 1000 W/m2, is 6.23% and 10.41% higher than that of the PVT system, respectively. Besides, the electrical efficiency of the PVT and PVT/TE by increasing the inlet... 

The solar collectors absorb solar irradiation and then produce thermal energy; however, they cannot generate electrical power. Electricity and thermal energy can be produced by the photovoltaic thermal module, simultaneously, while the outlet temperature of the photovoltaic thermal module is not usually high enough to provide thermal requirements of a building such as hot water or space heating. This work proposes a novel compound system created by the connection of a solar collector in series with a photovoltaic thermal module to resolve the issue of low outlet temperature in the photovoltaic thermal module and lack of electrical power in solar collectors. To examine the feasibility of this... 

In project management context, the Earned Value Management (EVM) is a well-known technique. Despite its popularity, the standard EVM suffers from the absence of some features that require being focused further on to make this method more efficient. This paper is addressing such features specifically the financial aspects of cost control system. These aspects that have been absent in the standard EVM include the time value of money, delay in client payment and contractor cash flow in uncertain environment. The proposed model here utilizes fuzzy sets to deal with the uncertain conditions of real projects. It attempts to extend the theoretical framework of EVM to evaluate and control the... 

The mechanism of selectivity in ion channels is still an open question in biology for more than half a century. Here, we suggest that quantum interference can be a solution to explain the selectivity mechanism in ion channels since interference happens between similar ions through the same size of ion channels. In this paper, we simulate two neighboring ion channels on a cell membrane with the famous double-slit experiment in physics to investigate whether there is any possibility of matter-wave interference of ions via movement through ion channels. Our obtained decoherence timescales indicate that the quantum states of ions can only survive for short times, i.e. ∼100 picoseconds in each... 

Lorentz force is the pumping basis of many electromagnetic micropumps used in lab-on-a-chip. In this paper a novel reciprocating single-chamber micropump is proposed, in which the actuation technique is based on Lorentz force acting on an array of microwires attached on a membrane surface. An alternating current is applied through the microwires in the presence of a magnetic field. The resultant force causes the membrane to oscillate and pushes the fluid to flow through microchannel using a ball-valve. The pump chamber (3 mm depth) was fabricated on a Polymethylmethacrylate (PMMA) substrate using laser engraving technique. The chamber was covered by a 60 μm thick hyper-elastic latex rubber... 

In an attempt to prolong the performance of the conventional Solar Chimney (SC) and enhance its efficiency, this contribution presents a kind of novel compound SC with the Photovoltaic (PV) module and Phase Change Material (PCM) called the SC-PV-PCM system. Using PCM not only improves the PV module performance but also extends the productive period of the SC. A three-dimensional quasi-steady computational fluid dynamics (CFD) model of the proposed system is developed. The developed model is used to investigate the effect of using PCMs with different melting points on the performance of the proposed system. It is demonstrated that the RT-50 provides superior performance among the studied... 

Optimized conditions of hot and cold rolling followed by annealing can result in a balance between recrystallization and rolling textures in order to reduce the planar anisotropy of brass sheets. In this work, the effect of finish rolling temperature, cold reduction and annealing temperature on texture development has been investigated. It is shown that uniform deformation at higher finishing temperature is responsible of formation of a severe Cube and G texture components. In contrast, mechanical twinnings are widely formed at low finishing temperatures. There is also a direct relation between the intensity of Cube component and the amount of cold reduction  

Ant colony optimization (ACO) is a well-known metaheuristic in which a colony of artificial ants cooperate in exploring good solutions to a combinatorial optimization problem. In this paper, an ACO algorithm is presented for the graph coloring problem. This ACO algorithm conforms to max-min ant system structure and exploits a local search heuristic to improve its performance. Experimental results on DIMACS test instances show improvements over existing ACO algorithms of the graph coloring problem  

Convection heat transfer below a horizontal, hot, and isothermal strip of infinite length and width of 2L embedded in fluids with different Prandtl number (Pr) and Nusselt number (Nu) is analyzed with the aid of integral method. A new concept is utilized to determine the boundary layer thickness at the strip's edge, which is based on matching the flow rate of the boundary layer below the strip at its edge and the flow rate of the plume, which forms after the heated fluid detaches from the strip's edge. In addition to these novelties, a numerical model is developed to verify the analytical framework, and an excellent agreement is observed between the analytical and numerical models  

This work aims to compare results of dissipating and pure dephasing single-qubit probes in characterizing the cutoff frequency of a harmonic reservoir Ohmic spectral density. In particular, we proved that a dissipating single-qubit improves the estimation precision of the cutoff frequency estimator. The information backflow and outflow of the dissipating and the dephasing single-qubit are compared. The relation between the quantum Fisher information and the information outflow and backflow of the probe is obtained. The results show that difference between the values of information outflow and backflow of a dissipating single-qubit is larger than a dephasing single-qubit. So, a single-qubit... 

The bifacial photovoltaic/thermal module is an emerging concept that can provide electricity and heat simultaneously, taking advantage of both front and rear sides of the panel; therefore, exhibiting a better performance compared to a conventional photovoltaic module or photovoltaic thermal module. In this study, four configurations of the bifacial photovoltaic/thermal module with different cooling methods have been proposed, i.e., cooling performed at either the upper or the lower surface, in parallel (applied to both upper and lower surfaces having similar start/endpoints), and swinging air back and forth (by guiding the air over the upper and lower surfaces, respectively). The... 

In the current research, a three-dimensional photovoltaic thermal system integrated with phase change material system with nanofluids is investigated. The working fluids involved in this study include nano-magnesium oxide, multiwall carbon nano tube and hybrid (mixture of nano-magnesium oxide and nano-multiwall carbon nano tube) nanofluids dispersed in pure water. After comparing single-phase model and mixture model, the mixture model is used in the study and fluid flow regime in the collector is assumed to be laminar, fully develop, uniform and incompressible, to model the nanofluid in the system. A parametric analysis is conducted to examine the effect of various parameters such as working... 

One of the most prominent hybrid solar devices is the photovoltaic thermal system (PVTS), which is able to provide simultaneous electricity and thermal energy. The thermal energy is the heat absorbed by the photovoltaic (PV) module and transferred to the attached thermal collector and finally to the heat transfer fluid. Utilizing a proper heat transfer fluid is an effective means to increase in obtained thermal and electrical powers and enhance PV thermal management. Over the past decade, employing nanofluids thanks to their superior thermophysical properties became a proved strategy to improve the efficiency of the PVTS. This paper covers cutting-edge researches on nanofluid-based PVTS via... 

One of the most prominent hybrid solar devices is the photovoltaic thermal system (PVTS), which is able to provide simultaneous electricity and thermal energy. The thermal energy is the heat absorbed by the photovoltaic (PV) module and transferred to the attached thermal collector and finally to the heat transfer fluid. Utilizing a proper heat transfer fluid is an effective means to increase in obtained thermal and electrical powers and enhance PV thermal management. Over the past decade, employing nanofluids thanks to their superior thermophysical properties became a proved strategy to improve the efficiency of the PVTS. This paper covers cutting-edge researches on nanofluid-based PVTS via...