Sharif Digital Repository

The main aim of this study was to improve current efficiency and to obtain thicker coatings via aluminum oxide (Al2O3) addition to the chromium (Cr) (III) bath. Design/methodology/approach ‐ Pure Cr and nanocomposite Cr–Al2O3 coatings were electrodeposited from Cr (III) bath onto cathode copper substrates by conventional method. Dependence of current efficiency to current density, Al2O3 content and particle size were investigated. Findings ‐ Current efficiency increased with Al2O3 amount and decreased with Al2O3 particle size. Maximum current efficiency was achieved at 25 A/dm2 for pure Cr and 30 A/dm2 for composite coatings. Al2O3 bath content, current density and stirring rate increased... 

Cr and Cr-Al2O3 coatings were electrodeposited from Cr(III) bath with both pulsating and direct current onto copper substrates. Pulsating current resulted in homogeneous films of higher Al2O3 content and lower particle agglomeration than the direct current. Differences were more tangible at shorter duty cycles and pulse frequencies. Pulsating current improved both microhardness and corrosion resistance. The presence of alumina nanoparticles resulted in greater current efficiency, higher film microhardness and better corrosion resistance. Maximum current efficiency, highest microhardness and densest electrodeposited coatings were achieved at current density of 20 A dm-2, duty cycle of 40% and... 

A two-step pack cementation technique was used to cover nickel-based IN-738LC superalloy with a Cr-aluminide coating layer. The IN-738LC/Cr-aluminide samples were oxidized at 900 °C for 350 and 700 h, isothermally, and 175 and 350 h, cyclically. Each cycle lasted for 25 h. Effects of the isothermal and the cyclic oxidation on (a) morphology, (b) new-phase formation, (c) weight gain, and (d) oxidation reactions were investigated by scanning electron microscopy, electron dispersive spectroscopy, X-ray diffraction, and weight gain measurements. From results, it was concluded that the oxygen attack was more severe during the cyclic oxidation than the isothermal procedure. Kinetics of the... 

Optimum operating parameters for pulse co-deposition of nano-Al2O3 with Cr from a trivalent chromium bath onto Cu cathode are selected by using “technique for order performance by similarity to ideal solution” (TOPSIS), “VIšekriterijumsko KOmpromisno Rangiranje” (VIKOR), “elimination and choice expressing the reality” (ELECTRE) and “complex proportional assessment” (CORPAS) accompanied with analytic hierarchy processing (AHP) to compare methods for achievement of the best tribological coating performance. Criteria for appropriate selection include wear loss, corrosion resistance, micro-hardness, bath condition and current efficiency. Results ascertain the best Cr–Al2O3 nano-composite coating... 

The effect of NaOH content of electrolyte on the properties of ceramic coatings, produced in silicate solution, was studied. Morphology, chemical analysis, phase composition, and cross-section of the ceramic coatings were investigated by SEM, EDS, XRD, and OM, respectively. The corrosion resistance and corrosion mechanism were also studied using potentiodynamic polarization and electrochemical impedance spectroscopy in a 3.5% NaCl solution. To study the surface roughness, a brightness SEM image analysis method was used. Results suggested that increasing the NaOH concentration of sediment production size causes thickness and coating roughness to decrease. The lowest corrosion rate belonged to... 

Hot corrosion is a serious problem in gas turbines due to poor quality fuels which contain Na, V, S and Cl. To resolve the problem, Cr-aluminide was coated on IN-738LC superalloy with a two steps pack cementation process. Oxidation behavior and near-surface microstructure of the coating showed consecutive increase in destruction by exposition to Na2SO4, 75Na2SO4 + 25 V2O5 and 70Na2SO4 + 25 V2O5 + 5NaCl (wt.%). Kinetic studies indicated parabolic corrosion rate in salt-less samples due to diffusion. Similar expression for salt-covered samples was assessed for oxide dissolution. Plate-like, broken-plate-like and cauliflower-like morphologies attributed to the corrosion products were observed... 

This work describes coating of NiCoCrAlY on IN-738LC superalloy by high-velocity oxygen fuel (HVOF) process. Properties of the coatings are significantly influenced by oxygen/fuel ratio and other spraying parameters. The effect of oxygen/fuel ratio on the oxidation behavior, bond strength, hardness, roughness and microstructure including porosity, inclusion formation and unmelted particles are discussed here. The porosity and inclusion in C1 coating are maximal. C2 coating with oxygen/fuel ratio of 2 has the highest bond strength and the lowest unmelted particles. C3 coating with the lowest total porosity and inclusion has the minimal roughness and the highest oxidation resistance and... 

Abstract: This work describes coating of NiCoCrAlY on IN-738LC superalloy by high-velocity oxygen fuel (HVOF) process. Properties of the coatings are significantly influenced by oxygen/fuel ratio and other spraying parameters. The effect of oxygen/fuel ratio on the oxidation behavior, bond strength, hardness, roughness and microstructure including porosity, inclusion formation and unmelted particles are discussed here. The porosity and inclusion in C1 coating are maximal. C2 coating with oxygen/fuel ratio of 2 has the highest bond strength and the lowest unmelted particles. C3 coating with the lowest total porosity and inclusion has the minimal roughness and the highest oxidation resistance... 

Thermal-sprayed MCrAlY coatings have become widespread in various industries such as power plants, aeronautics, and oil and gas firms. High-temperature oxidation behavior of these coatings is therefore of significance. Spraying of two prevalent MCrAlY powders (NiCoCrAlY and CoNiCrAlY) on Hastelloy substrate by high velocity oxygen and fuel method and exposing them to 1000 °C air for resolving of their cyclic oxidation behavior are presented in this paper. The coatings were characterized by x-ray diffraction, scanning electron microscopy and energy-dispersive x-ray spectroscopy. The obtained oxidation kinetic indicated that at 1000 °C, the thermally sprayed NiCoCrAlY coating has greater... 

I present an in-depth review of the trends and the directions taken by researchers worldwide in optical code-division multiple-access (OCDMA) systems. I highlight those trends and features that I believe are essential to the successful introduction of various OCDMA techniques in communication systems and data networks in the near future. In particular I begin by giving a comprehensive review of the construction of optical orthogonal codes (OOCs). Specifically I discuss the recently developed algorithms that are based on matrix algebra, which simplify and enhance the efficiencies of algorithms in OOC generation. In communication systems studies I first focus on and discuss various OCDMA... 

Using 3-D scanned data to analyze and extract pore network plays a vital role in investigation of porous media's characteristics. In this paper, a new simple method is developed to detect pores and throats for analyzing the connectivity and permeability of the network. This automated method utilizes some of the common and well-known image processing functions which are widely accessible by researchers and this has led to an easy algorithm implementation. In this method, after polishing and quality control of images, using city-block distance function and watershed segmentation algorithm, pores and throats are detected and 3-D network is produced. This method can also be applied on 2-D images...