Sharif Digital Repository

In this paper an efficient method is proposed for blind detection of multiuser spread spectrum signal and pseudo noise (PN) length estimation in downlink scenario. This method is based on fluctuating observation of second order statistic (SOS) estimator of received signal; estimating length of spreading code with no need to primary information based on observing second order peaks of correlation estimator is presented. In low SNR, the fading multipath phenomenon especially in length of small codes leads to problem in detecting place of correlation estimator peaks. In this paper besides expanding blind estimation to multiuser environment, by using searching method in updating the length of... 

A novel, robust and practical method for active user enumeration in asynchronous CDMA in multipath channel condition is proposed in this paper. Most of the previous works do not consider the fact that in practical case, user's signals with the help of receiver arrive asynchronously. The proposed method can be used practically in blind multi-user detection such as eavesdropping; moreover, the method is based on information theory criteria which outperform other methods. Minimum description length (MDL) has better performance than all other information criteria used in such scenarios. Unlike most of the pervious works, we do not exploit array antenna to gather necessary data of the users.... 

IN this paper the effect of different channel estimation approaches in OFDMA uplink system which are based on Basis Expansion Model (BEM) and widely used to consider time varying channels are discussed. It has been shown in previous works that modeling error will be reduced by applying oversampled BEM with cost of increasing sensitivity to noise. This problem will be solved by combining oversampled BEM and MMSE channel estimator with cost of increasing computational complexity. In this paper a novel channel estimation approach is represented in which by combining oversampled BEM and low rank MMSE in frequency domain, almost the same performance as the full rank MMSE has been achieved while... 

It was shown that the number of array elements must exceed the number of sources for subspace-based direction-of-arrival (DOA) estimation. But this is not practical for a direct-sequence code-division multiple access (DS-CDMA) wireless system, since the number of mobile users is very large. To remove the aforementioned restriction, a DOA estimator, employing the code-matched filters and parallel ESPRIT algorithms, is proposed. This algorithm does not use to search all angles such as MUSIC method. Besides, it is not necessary to use AIC and MDL criterion to estimate the number of sources in the proposed algorithm. Simulation results illustrates the appropriate performance of the new method  

The architecture of the Cascading TMR (Triple Modular Redundancy) System is commonly found in aerospace applications. The system is potentially capable of containing a large number of modules and sub modules. In this paper a novel method for optimization of a Cascading TMR system configuration using GA (Genetic Algorithm) is proposed. The proposed algorithm provides a configuration that maximizes reliability and minimizes overhead area simultaneously  

In this paper a novel Space Time Diversity Generalized Decorrelating Discrete Time Rake (STD-GD-DTR) for Upstream DS-CDMA system is proposed. The chosen algorithm for estimating the correct data is Maximum likelihood. In this method, a robust receiver based on maximum likelihood estimation is represented in which, space time diversity technique has been combined with generalized decorrelating discrete-time RAKE (GD-DTR) receiver to obtain higher performance than other widely used techniques for data estimation. Our proposed STD-GD-DTR ML based receiver provides high gains in the presence of channel estimation errors from similar methods. Simulation results illustrate the appropriate... 

Comparison of the traditional linear heating method of TPD with an original stepwise heating scheme was reported for the first time. Stepwise heating TPD was carried out by keeping the temperature constant as soon as ammonia desorption signal rises until the signal returns to the baseline. More ammonia desorption peaks on a SAPO-34 catalyst were identified using TPD with stepwise heating. The effect of temperature ramp on desorption peak broadening in TPD curve was also addressed. The more distinct ammonia desorption peaks in stepwise TPD indicates that ammonia adsorbs in about five or six different ways on SAPO-34, and attribution of different adsorptions may be explained considering some... 

Most part of Iran is dominated by arid and semi-arid areas due to low annual rainfall. The need for production of fresh water from brackish water is considerably high, especially in dry regions. In this study 1 month daily-based experimental data from a solar still site has been reported. The technical and operational problems of this site which finally contributed to the total cease of the site are described. Then a detailed analysis is investigated on progress of a prototype which constructed in order to solve the site's problems. The results of 1 month of experimental data of the final design showed that the last prototype could be used to solve the current problems of the site. The... 

Hydrocracking is one of the most versatile petroleum refining processes for production of valuable products including gasoline, gas oil, and jet fuel. In this paper, a five-parameter continuous lumping model was used for kinetic modeling of hydrocracking of vacuum gas oil (VGO). The model parameters were estimated from industrial data obtained from a fixed bed reactor operating at an average temperature of 400°C and residence time of 0.3 h. Product distributions were obtained in terms of the weight fraction of various boiling point cuts. The model parameters were estimated using the Nelder-Mead optimization procedure and were correlated with temperature. Comparison of experimental and... 

Purpose - The purpose of this paper is to present an improved methodology for design of custom-made hip prostheses, through integration of advanced image processing, computer aided design (CAD) and additive manufacturing (AM) technologies. Design/methodology/approach - The proposed methodology for design of custom-made hip prostheses is based on an independent design criterion for each of the intra-medullary and extra-medullary portions of the prosthesis. The intra-medullar part of the prosthesis is designed using a more accurate and detailed description of the 3D geometry of the femoral intra-medullary cavity, including the septum calcar ridge, so that an improved fill and fit performance... 

In this letter, we propose a method for real-time high density impulse noise suppression from images. In our method, we first apply an impulse detector to identify the corrupted pixels and then employ an innovative weighted-average filter to restore them. The filter takes the nearest neighboring interpolated image as the initial image and computes the weights according to the relative positions of the corrupted and uncorrupted pixels. Experimental results show that the proposed method outperforms the best existing methods in both PSNR measure and visual quality and is quite suitable for real-time applications  

The disposal of used tires is a major environmental problem. With increasing interest on recovery of wastes, pyrolysis is considered as an alternative process for recovering some of the value in scrap tires. An accurate kinetic model is required to predict product yields during thermal or catalytic pyrolysis of scrap tires. Pyrolysis products contain a variety of hydrocarbons over a wide boiling range. A common approach for kinetic modeling of such complex systems is lumping where each lump is defined by a boiling point range. Available experimental data for thermal and catalytic pyrolysis of scrap tires from the literature were used to evaluate two types of lumping models; discrete and... 

Compared with flat linear structures, tubular linear machines do not face edge effects, making their performance better than their flat counterparts. In this article, a novel linear variable-reluctance resolver with tubular configuration is proposed. To optimize the design of an electromagnetic structure, modeling methods are used. Thus, in this article, an analytical model for the proposed resolver is presented. This model is based on the magnetic equivalent circuit (MEC) method and is considerably less time-consuming than finite element analysis (FEA), yet provides accurate results. A conformal mapping is employed to compute the permeance of the air-gap. The proposed model is then utilized... 

In Brukner and Zeilinger's interpretation of quantum mechanics, information is introduced as the most fundamental notion and the finiteness of information is considered as an essential feature of quantum systems. They also define a new measure of information which is inherently different from the Shannon information and try to show that the latter is not useful in defining the information content in a quantum object. Here, we show that there are serious problems in their approach which make their efforts unsatisfactory. The finiteness of information does not explain how objective results appear in experiments and what an instantaneous change in the so-called information vector (or catalog of...