Sharif Digital Repository

The strain-induced martensitic transformation greatly affects the plastic behavior of the metastable austenitic stainless steels. The martensitic transformation continuously changes the initially homogeneous material into a strongly heterogeneous bi-phase one. In addition to the hardening behavior, this phenomenon would influence the damage growth and load-carrying capacity of the material during the plastic deformation. In this study, plastic behavior of the material AISI 304 including the hardening and damage growth, has been examined at low temperature; where a high rate of martensitic transformation affects the microstructure strongly. Experimental analysis and microscopic observations... 

In this report, crack-free nanostructured barium titanate thin films are prepared by a sol-gel processing method. Glacial acetic acid, barium acetate, titanium tetraisopropyl alkoxide, 2-propanol and deionized water are used as precursors for preparing stable precursor solution. Then very thin films (thickness=26 nm) are deposited on fused silica substrates. In order to prepare crack-free thin films of BaTiO3, much attention is given to solvent evaporation process and a controlled pre-drying process is developed. It is found that the control of the process, especially in the initial stage of drying process is crucial and important for preparation of the crack-free ultrathin nanostructured... 

TiO2nanocrystals were prepared by hydrolysis and peptisation of titanium isopropoxide under different pH values. The as-prepared powder of very fine anatase crystallites ranges from 8 nm in acidic solution of pH 3 to 10 nm in basic solution of pH 8. Heat treatment of the powders leads to grain growth and anatase - rutile transformation. Experimental results have shown that the anatase to rutile phase transformation in the heat-treated powders depend not only on primary crystallite size but also the presence of brookite phase. It is observed that in the powders with the same size the presence brookite phase would accelerate the anatase to rutile transformation. Furthermore it has been found... 

Statistical Process Control (SPC) is an approach that uses statistical techniques to monitor the process. The techniques of quality control are widely used in controlling any kinds of processes. One of these processes is the short processes. In short run processes often do not have enough data in each run to produce good estimates of the process parameters. This will cause the reduction of the performance and efficiency of control charts. A common solution to this problem is considering a single machine or process to produce many different parts, or different products. In this paper a new method based on non-conformity degree and fuzzy membership functions has been developed for controlling... 

In this paper, Sugimoto model has been employed to study the nucleation and the growth of TiO2 nanoparticles. On the base of this model some parameters of the nucleation and the growth of nanoparticles such as supply rate of the solute (Q0), molar volume of the solid (Vm), and mean volumic growth rate of the stable nuclei during the nucleation period (v) were determined. For this approach, TiO2 nanoparticles were synthesized in two stages in an aqueous solution by using HNO3 and TTIP and TIPO as starting materials. In this experiment, it was obviously observed that the changing of Ti+4concentrations was followed with LaMer diagram. Typical obtained results were v=2.93×102 nm3.s -1 and... 

Titanium dioxide nanopowders were synthesized by the diffusion controlled sol-gel process (LaMer model) and characterized by DTA-TG, XRD, and SEM. The prepared TiO 2 nanoparticles have uniform size and morphology, and the phase transformation kinetics of obtained material was studied by interpretation of the X-ray diffraction patterns peaks on the base of Avrami equation. The stating point of anatase-rutile phase transformation temperature in the prepared nanoparticles was found between 100 and 200 C. A decreasing trend on the intensity of X-ray peaks of anatase phase was observed up to 600 C when the presence of the rutile phase became predominant. Results indicated that the transition... 

Amorphous barium titanate nanothin films were prepared by sol-gel dip-coating method. According to transmission spectrum, the refractive index and optical band gap of nanothin films have been determined. High transmission spectrum without any fluctuation in visible wavelength region was recorded. Experimental results indicated that the surface morphology of prepared nanothin films were improved and as a result of that, a better optical properties, less optical losses and higher band gap width were obtained in contrast with other reported data. It was found that optical propagation loss of BaTiO3 nanothin film was much lower than normal polycrystalline BaTiO3 thin film. It seems to us that,... 

This work aims to develop a chemically modified sol–gel synthesis pathway for obtaining various barium titanate nanostructures. The method is able to prepare different BaTiO3 nanostructures such as highly stable nanoparticle embedded colloids, highly transparent amorphous nanolayers, nanocrystalline BaTiO3 powders and ultrathin BaTiO3 nanostructured films directly from a precursor solution. All the products have been prepared at a lower temperature and in a more cost-effective way in contrast to other established sol–gel methods. The results show that the optical transparency of the thin films has been significantly improved in contrast to the similar researches. The deposited thin film is... 

In this research, a modified, cost effective sol-gel procedure applied to synthesize BaTiO3 nanoparticles. XRD and electron microscopy (SEM and TEM) applied for microstructural characterization of powders. The obtained results showed that the type of precursors, their ratio and the hydrolysis conditions had a great effect on time, temperature and therefore the costs of the synthesis process. By selection, utilization of optimized precursor's type, hydrolysis conditions, fine cubic BaTiO3 nanoparticles were synthesized at low temperature and in short time span (1 h calcination at 800 °C). The proposed procedure seems to be more preferable for mass production. The result indicated that the... 

Biphase TiO2 nanoparticles have been prepared by sol-gel method. Water/titanium molar ratio (r) has been used to control the hydrolysis and condensation of titanium isopropoxide in solution producing titanium oxide with two different polymorphs. The influence of crystallite size and morphology of prepared TiO2 on the phase transformation of the resultant materials has been investigated. Synthesized powders were characterized by X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Different trends can be observed in the phase transformation and particle growth of the prepared titanium oxide nanomaterial. It was concluded that, the rate of particle... 

Hydrolysis of titanium isopropoxide alcoholic solution has been used to prepare the crystallized TiO2 nanoparticles at low temperature. Concentration ratio was used to control the pathway of sol-gel process and change the physical characteristics of TiO2 nanopowders. The crystallinity, morphology and size of aged TiO2 nanopowders were studied by X-ray diffraction and Scanning Electron Microscopy (SEM). FTIR and, Thermo-Gravimetric (TG) analysis were used to identify the functional groups and thermal behavior of prepared samples. Experimental results have shown that high crystalline TiO2 nanomaterial with anatase polymorph can be obtained at room temperature. It has been found that the...