Sharif Digital Repository

Dye sensitized solar cells are one of the cheap and available technologies that have attracted the attention of many researchers. Many factors such as morphology, microstructure, phase composition and the arrangement of photoanode electrode layers have an effect on the photovoltaic properties of DSSCs. Different approaches have been used to improve the efficiency of this type of cells. Among these approaches, we can mention the use of a mixture of different phases of titanium dioxide and the use of perovskite titanate structures as photoanodes. In the current study, the performance of nickel titanate on light absorption and electron-hole separation in titanium dioxide-based dye-sensitized... 

Noise or noise pollution, is defined as an unwanted sound, produced mostly by motor vehicles in urban areas. If the noise exceeds its limit, adverse effects on users and citizens are expected. Thus the assessment of the noise level and its comparison with allowable values is mandatory. Traffic induced noise depends upon different factors such as traffic, weather, and, sound barriers. Noise pollution study has a long history all over the world. Many studies, mostly representing the outdoor noise pollution models, have been done in recent years. This paper presents an assessment of traffic-induced noise in a heavily traveled tunnel, locally referred to as Resalat tunnel, which is located in... 

Data collected from street networks show that travel time in urban street networks is a stochastic variable, whose range of variation increases with the congestion level. Work and school trips comprise the major part of morning peak volumes, whose common characteristic is that they need to be made on time. For this reason, these travelers are pessimistic in their route choice, and try to choose routes which are more reliable. Travel time standard deviation is one of the common measures for estimating travel time reliability that is related to properties of day-to-day travel time distribution on a particular route. Based on the empirical data collected from Tehran street network, this paper... 

With the advancement of automotive industry, the number of electronic systems that need to communicate with each other has increased. An effective strategy to meet these growing demands is using bus-based protocols, which can establish safe communication among numerous nodes with reasonable cost, weight, and space requirements. The objective of this thesis is the design and implementation of a transceiver based on the FlexRay protocol. The significance of this protocol lies in its ability to provide higher data transmission rates compared to other protocols like CAN and LIN, and its role as the foundational communication medium among various domains in modern vehicle architectures. In this... 

In this thesis, we introduce a novel Artificial Intelligence (AI) system inspired by the philosophical and psychoanalytical concept of imagination as a ``Re-construction of Experiences". Our AI system is equipped with an imagination-inspired module that bridges the gap between textual inputs and other modalities, enriching the derived information based on previously learned experiences. A unique feature of our system is its ability to formulate independent perceptions of inputs. This leads to unique interpretations of a concept that may differ from human interpretations but are equally valid, a phenomenon we term as ``Interpretable Misunderstanding". We employ large-scale models,... 

Quantum entanglement is an essential resource in quantum information processing, such as quantum communication and quantum computing. Although entanglement is critical for practical implementations in these fields, creating and transmitting entanglement without altering the states is challenging. External noise may destroy or weaken the entanglement. Consequently, there is a need for methods to improve entanglement. Entanglement distillation is an effort to address this issue. It is a process where, probabilistically, a smaller number of strongly entangled states are created from a fixed number of noisy entangled states. This process is carried out using only local operations and classical... 

Optimizing optical tweezers and achieving powerful traps has always been a challenging topic for researchers , since the trap stiffness increases with increasing laser power which may damage specimens , especially biological ones and cells . In this thesis , we introduce a special geometry and structure of particles that , have the possibility to increase the stiffness (strength) of the optical trap and cause the magnetic response of particles at optical frequencies . Special geometries such as a combination of dielectric particles with magnetic nanoparticles that emphasize the role of the laser magnetic field and lead to changes in the electrical and magnetic properties at the laser... 

Ni-Co/SiC composite coatings with various contents of SiC nano particles were electrodeposited in a modified watt type of Ni-Co bath containing 20 nm SiC nano particles to be codeposited. The influences of the SiC concentration, current density, stirring rate of the deposition bath on the composition of the coatings were investigated and these parameters optimized for highest amount of SiC codeposition. The optimized deposition parameters were 40 g/l SiC and 480 rpm stirring rate and current density equal to 4 A/dm2. Ni-Co/SiC composite coating was deposited with the maximum particles content of 30.5 volume percent. Linear voltammetry demonstrates addition of the SiC to the Ni-Co deposition... 

Many of the major structure over coastal waters in the Kish Island due to the aggressive condition are showing signs of reinforcement corrosion. Recent advances in the development of anodes make it practical to use zinc galvanic cathodic protection to protect this structure in this area. Five anode systems were tested on several samples as, (1) zinc metal spray applied by arc-spraying on the concrete, (2) a zinc foil with conductive adhesive backing, (3) a system of zinc mesh and grout jacket, (4) a system of zinc mesh and compression panels, and (5) a bulk zinc. These anodes are set up to comparison the effects of potential and current over the zinc galvanic cathodic protection during 4... 

Metal matrix nanocomposites contains ceramic ultrafine particles in a metal matrix, are used to improve the mechanical properties such as hardness and wear of coatings. For developing metal matrix nanocomposites, there are many methods. Electrochemical deposition process is one of these methods that have some advantages like uniform depositions on substrates with complex shapes, low cost, good repeatability and reducing waste. In this project, for increasing the hardness and wear resistance of nickel, composite coatings of nickel - titanium nitride was created by using electrochemical deposition of Watts bath contained titanium nitride particles. In order to increase the amount of... 

In this work, a novel type electrode based on RuO2 nanoparticles-modified vertically aligned carbon nanotubes (RuO2/MWCNTs) was investigated. ThisRuO2/MWCNTs electrode not only shows a high capacity nature,but also possesses a good response to the pH value. In order to develope this sensor, aligned carbon nanotubes were synthesized by the chemical vapor deposition at first and then modified with RuO2 nanopartcles by sol-gel method. Various parameters affecting the growth of nanotubes, such as substrate type, surface finishing, surface roughness, the growth temperature and carbon feed rate was studiedand and optimal conditions for growth were obtained. At last, aligned nanotubes with a... 

Ni-P alloy coatings were electrodeposited using pulse current in a watt type bath in various conditions. The influences of different parameters were investigated and optimized for the highest amount of coating hardness using the Design Of Experiment (DOE) method. The optimized deposition parameters were current density 23.7 A/dm2, duty cycle 75%, frequency equal to 188 Hz, temperature equal to 70ºC and 17.5 gr/l of H3PO3. The DOE prediction of hardness for the optimized coatings was between 700 and 750 the achieved micro-hardness was about 725.8 HV. It was obtained that an increase of the current density will improve micro-hardness, decreases P content and increase deposition rate. Also, the... 

In this research project, Ni electrodeposition process has been modeled by a 3D coupled continuum-kinetic Monte Carlo simulation. Kinetic Monte Carlo module processes surface reactions along the substrate using electrochemical equations for the relating events. Continuum model also determines concentration of the whole system according to a 3D interpretation of diffusion law in solutions. After running each module, exchange of data between two codes is done and boundary conditions are updated. In fact, the whole simulation time is divided by small time steps relating to time fastest reactions need to proceed. Present model will generate three outputs: current-time curve, surface morphology... 

This research describes a new and relatively general method to grow well-aligned carbon nanotubes (CNTs) on cobalt-deposited stainless steel by thermal chemical vapor deposition (CVD) of ethylenediamine precursor. The CNTs are vertically aligned at high density over large areas on the surface. Different effective parameters in growth of carbon nanotubes, as type of substrate, surface treatment, temperature of growth , feeding carbon supplies have been studied. Finally, aligned carbon nanotubes have been prepared by 100-150 nm diameter and 9µ length. CoOx•nH2O–MWCNTs nanocomposites were successfully synthesized, using a cathodic electrochemical reduction of H2O2 to deposit cobalt... 

Thin film of Indium oxide doped with tin is used as a transparent electrode for different applications like screening panels, solar cells, touch panels and elechtrochromic tools. Trading thin films of ITO are precipitated using sputtering. However sol gel method can be simple and economic to make transparent electrodes. In this thesis first ITO sols is prepared using Indium nitrate and tin chloride with two or four capacities due to the production of transparent oxides on soda lime glass. Then the effect of tin chloride with two and four capacities is investigated on resistance and optic properties. Results show that tin chloride with four capacities in comparison with tin of two capacities... 

Antimony Doped tin oxide as a conductive film has found a wide range of applications and sol-gel method has so advantageous with respect to another methods for preparing ATO thin films. In this study, ATO thin film has been synthesized using a solution containing metal salts of tin chloride and antimony chloride. The microstructure of the obtained films was studied by applying scanning electron microscopy (SEM) and X-ray diffraction patterns (XRD). In diffraction patterns of the acquired ATO layers which was deposited from a sol containing SnCl4.5H2O and SnCl2.2H2O with Sb concentration of 15%mol and layers which was deposited from a sol containing SnCl4.5H2O with Sb concentration of 15%mol... 

In recent years, different of nanoparticles as oil additives has been investigated in many studies . These research show that nanoparticles are deposited on the surface friction and improve tribology properties of base oil and also significant reduction of wear and friction caused by the nanoparticles. Compared with metal and metal oxide nanoparticles , carbon nanotubes (CNT) due to the high thermal conductivity and high aspect ratio , is an excellent candidate as the nanoparticle is dispersed . For preparing useful oil it is essential to stabilize nanoparticles in fluid that will not settle over long time . Oils containing nanoparticles by increasing the heat transfer coefficient... 

Platinum nanotubes were deposited inside the pores of polycarbonate template with the pore size of 200 nm by electrochemical methods. In this regard a solution containing of 0.05 M H2PtCl6 and 0. 1 M H2SO4 in doubly distilled water was utilized. The electrodeposition process was studied by electrochemical techniques such as voltammetry and chronoamperometry methods. It was observed that the process was conducted in several stages including; nucleation and growth in steady state regime. Furthermore, it was concluded that electrodeposition was affected by mass transport restriction and was controlled by a diffusion process. In this regard, all the voltammograms were shifted to more negative... 

Reinforced concrete is one of the most important structural materials used in the construction industry worldwide. Nevertheless, certain physical and chemical factors in the service environment can contribute to its deterioration and failure. One of the most significant factors is the reinforcing steel bar (rebar) corrosion. In order to minimize the rebars corrosion, different kinds of coatings were investigated and evaluated by scientists. In this investigation comparative studies were performed on two different kinds of coated rebars (zinc-rich epoxy and polyamide epoxy coated rebars) and uncoated rebar. In order to evaluate these reinforced concretes, the adhesion, durability, thickness...