Sharif Digital Repository

Experiments were performed to explore the free convective hat transfer characteristics of water based nanofluids. Experiments of natural convection over a vertical flat plate with constant heat flux in water-based nanofluids with Ag and TiO2 nanoparticles were performed. Velocity boundary layer measured using PIV method. Also convective heat transfer coefficient obtained using three thermometers behind the wall. Various test cases with different heat fluxes on the wall are considered. Two volumetric concentrations of Ag nanofluid, 1% and 2%, and TiO2 nanofluid, 1% and 2%, were tested in the present study. It was shown that, with increasing nanofluid concentration, velocity boundary layer... 

Considering the fact that there is a blood flow inside the vessels it is possible that blood flow is always associated with fouling and this may decrease the blood flow when a blood vessel is injured, the cells of your blood bond together to form a blood clot. The blood clot helps you stop bleeding. Blood clots are made of a combination of blood cells, platelets (small sticky cells that speed up the clot-making process), and fibrin (protein that forms a thread-like mesh to trap cells). Doctors call this kind of blood clot a “thrombus.” We study the effects of different parameters on the deposition of Nanoparticles on the surface of a bump in the blood vessels by the magnetic field. The... 

Lithium-ion batteries have the ability to store a significant amount of energy and work at high power, which has led to the wide spread of their use in various industries. In high-power applications, battery heat management increases lifespan, safety, and reduces battery power loss. In this study, the heat management of a very common and widely used 18650 battery using multi-layered phase change material has been investigated. The reason for using multiple layers is that each phase change material has its own weaknesses in addition to its advantages. It is expected that with the proper use of several phase change materials in the thermal management system, the materials will reduce the... 

Oil pump is a prominent part which has been described as a vehicle heart. Any malfunction or improper design may lead to engine failure. beside engine, proper design of oil route and lubrication system of vehicle, are main factor in engine design, which provide higher efficiency with lower pressure drop. lubrication system should be able to provide required pressure and flow of oil in vast range of engine rotation speed. also minimum energy waste in higher rpm is a key factor which happens due to reverse flow from output to input of pump in the relief valve. The aim of this thesis focus on design of oil pump and lubrication system of 4 cylinder 16 valve of 1600 cc inline engine. which is... 

Providing fresh water, ending fossil fuels, using renewable energy and achieving a clean biological environment in different parts of the world especially in Iran beside having access to many saline water sources, Shows the need for research in the field of solar still desalination. The goal of current study is to increase the performance of the solar still system through the use of an energy storage system and an additional condenser. Adding an additional condenser to a conventional solar still lead to an increase in the rate of evaporation and consequently increase the production of the system. Also, by collecting distilled water from the sidewalls, the amount of water produced... 

At today’s crowded world, the importance of automobile transportation is obvious for all. The fossil fuel pollution crisis has increased the need for renewable-fueled engines with higher efficiency and lower emissions. Meanwhile, biofuels have received more attention for reasons such as carbon dioxide cycling, Affordability and availability. However, despite these benefits biofuels require crops such as corn or potatoes to produce, which in turn produce other environmental pollution. On the other hand, concerns have been raised as to whether the use of these fuels increases the amount of other pollutants, except for carbon dioxide, or not. Extensive researches in this field by experimental,... 

In this thesis, nitrogen-doped carbon quantum dots were synthesized from anhydrous trisodium citrate and arginine in water solvent by the hydrothermal method, which was used to develop an on-off-on fluorescence sensor. The hydrothermal method is a suitable method for the synthesis of nitrogen-doped carbon quantum dots due to its affordability, availability, rapidity, and safety. Characterization of nitrogen-doped carbon quantum dots was divided into two parts: in the first part, optical properties were investigated using fluorescence photoluminescence (PL) spectrometer and ultraviolet-visible spectrometer (UV-Vis), and in the second part, Fourier transform infrared spectrometry (FTIR),... 

One of the different methods of heat transfer, is pool boiling process. In this method, the operating fluid starts to boil on a hot surface whose temperature is more than boiling point of the fluid. Based on difference between between surface temperature and fluid boiling point, amount of heat flux from hot surface to fluid and fluid behavior will be different. In recent years, many researchers have tried to improve the amount of heat transfer in the boiling process by using various methods such as nanoparticle addition or using magnetic field.Latent heat is thermal energy released or absorbed, by a body or a thermodynamic system, during a constant-temperature process, usually a first-order... 

Droplet-based microfluidics offers a promising tool in engineering and biomedicine such as drug delivery, biochemistry, sample handling in lab-on-a-chip devices, and tissue engineering. These systems provide the droplets manipulation that can be used as reactors without any contamination for medical purposes. Utilizing magnetic force and ferrofluid droplets can help to better control over the droplet formation and manipulation. Considering the importance of this issue and its rich underlying physics, in this dissertation, ferrofluid droplets formation under a time-dependent, non-uniform magnetic field is studied. A Pulse-Width-Modulation signal (PWM) is utilized to apply the time-dependent... 

On track to achieve heat transfer methods for small-scale, this research describes the design process of fabrication and experimental analysis of micro heat pipes with a rectangular section. First, the overview of micro-fluid systems and conventional mechanisms of heat transfer in these systems is discussed. Then, in order to describe the research theory and principles of heat pipe, various types of heat pipes micro scale and macro scaled are analyzed. After that, the method used for fabrication of a micro heat pipe without grooves is described. A new method for fabrication of MHP is investigated in this study. By using this method, one fiber glass board is fabricated by printed circuit... 

Symmetric T junctions have been used widely in microfluidics to generate equal-sized microdroplets, which are applicable in drug delivery systems. A newly proposed method for generating unequal-size microdroplets at a T junction is investigated theoretically and experimentally. Asymmetric T junctions with branches of identical lengths and different cross-sections are utilized for this aim. A novel equation for the critical breakup of droplets at asymmetric T junctions and one for determining the breakup point of droplets are developed. A good agreement was observed between the theories (novel and previous) and the experiments  

This research study presents an experimental investigation on forced convection heat transfer of an aqueous ferrofluid flow passing through a circular copper tube in the presence of an alternating magnetic field. The flow passes through the tube under a uniform heat flux and laminar flow conditions. The primary objective was to intensify the particle migration and disturbance of the boundary layer by utilizing the magnetic field effect on the nanoparticles for more heat transfer enhancement. Complicated convection regimes caused by interactions between magnetic nanoparticles under various conditions were studied. The process of heat transfer was examined with different volume concentrations... 

Considering the advantages and disadvantages of reported micropumps, we aimed to introduce a novel idea to diminish the disadvantages and promote the advantages of PiezoElectric micropumps. This novel idea operates based on a mercury slug actuation in a microchannel. This cyclic motion of the mercury slug which is similar to a piston, push the fluid in the microchannel and pump the flow. However, to bring this idea into the practice, a control system must be designed. This system contains: LABVIEW code, DAQ board & a switching Board. The pattern of actuating mercury is drawn in LABVIEW. DAQ Board produces electrical signals according to LABVIEW code. Switching board will transform the... 

Developing of electric instruments with high performance needs high capacity heat transfer equipments. Pulsating heat pipes have better performance compared with normal heat pipes and can be used for cooling electronic instruments in near future. Also, one specific kind of heat pipes, which is called rotating pulsating heat pipe, can be used in cooling the turbine blades. Rotating pulsating heat pipe is a mechanism in which the pipes can rotate around the axis perpendicular to the plane of pipes. In this research one rotating heat pipe was built and the effects of heat input, filling ratio and rotational acceleration were examined experimentally. The Innovation in the research was to obtain... 

In this investigation Magneto Mercury Reciprocating Micrpump (MMRM) the combination of Magneto-Hydrodynamic and Reciprocating micropumps has been analyzed. To achieve the analytical and numerical solution of one-tank and three-tank MMRM, the momentum, continuity, volume fraction and magnetohydrodynamic equations have been presented. The dimensionless analytical solution of one-phase and two-phase three dimensional MHD flow in the condition of using constant current and potential electrical source, has been offered.
The boundary between mercury and air has been tracked via VOF method in OpenFOAM software. VOF equation has been solved by explicit method with variable time step and maximum... 

Nowadays, as a result of population growth and groundwater resources pollution, many countries in the world are facing serious water crises. Several alternative solutions have been investigated to overcome this obstacle. Atmospheric water vapor processing (AWVP) is a new solution to generate freshwater from ambient moist air. The atmosphere surrounding the earth is potentially a valuable water resource which contains a large amount of freshwater. This paper addresses the effectiveness of thermoelectric coolers (TECs) for refrigeration to produce freshwater from ambient air. Consequently, both numerical and experimental analysis are then used as the basis of water production calculation. 18... 

This research study presents an experimental investigation on forced convection heat transfer of an aqueous ferrofluid flow passing through a circular copper tube in the presence of a magnetic field. Both constant magnetic field and alternating magnetic field was examined. Moreover magnetic field layout and strength and modes of alternating magnetic field was investigated. The flow passes through the tube under a uniform heat flux and laminar flow conditions. The primary objective was to intensify the particle migration and disturbance of the boundary layer by utilizing the magnetic field effect on the nanoparticles for more heat transfer enhancement. Complicated convection regimes caused by... 

This research aims to design and build a device that Using solar energy and can be used as water heaters and water desalination and water from the soluble hygroscopic. For this purpose, a combination of evacuated tube collector with parabolic through collector with sun tracking mechanism is used. sun tracking mechanism is polar and works with optical sensor. in this research we have designed new setup with evacuated tube collector for direct desalination and water heater. in this method heat pipes have been omitted from setup that cause high performance in heat transfer from evacuated tube collector to water and is minimized losses. 15w air compressor used to increased rate of evaporation ... 

A Loop heat pipe (LHP) is an efficient two phase heat transfer device that is widely used in cooling applications. In this research a novel LHP was designed, fabricated and its performance was investigated through various experiments. The novel LHP has a new arrangement in evaporator and reservoir configuration in comparison with conventional LHPs, which results in a different energy and fluid flow. In addition, the novel LHP has a new mechanism for active control of working temperature which was not already used. Aside from its good performance, this LHP has easier and lower cost manufacturing process compared with the conventional ones. Also the proposed temperature control method is...