Sharif Digital Repository

Effect of using Al 2O 3-water nanofluids with different volume fractions and particle diameters on generated entropy, hydrodynamic performance and heat transfer characteristics of a tangential micro-heat sink (TMHS) was numerically investigated in this research. Results indicated that considerable heat transfer enhancement is possible when using Al 2O 3-water nanofluids as coolant and clearly the enhancement improves with increasing particles concentration and decreasing particles size. However, using nanofluid has also induced drastic effects on the pumping power that increases with particles volume fraction and Reynolds number. Finally, it was found that generated total entropy decreases... 

In this research, the problems of adiabatic film-cooling the flat, convex, and concave surfaces are investigated numerically. Two different radii of curvature and one row of vertical injection holes are considered. The Navier-Stokes equations are solved using a fine nonuniform multiblock staggered curvilinear grid and the SIMPLE-based finite volume method. The blowing rates are 0.5 and 1.0 and the mainstream Reynolds number is 10,000. The obtained results indicated that at a low blowing ratio, the cooling effectiveness enhances over the convex surface and reduces over the concave surface compared to the flat surface case. In comparison with the low blowing ratio, the curvature effects at a... 

Back extrusion technique was employed to characterize phase segregation tendency of mechanically stirred ZA27 alloy at different deformation rates. Variation of segregation intensity with ram diameter was found to follow opposite trends at low and high ram speeds. At sufficiently high ram speeds, small rams are of better performance in minimizing segregation whereas at low ram speeds, large rams result in less pronounced segregation. In addition, increasing ram speed invariably decreases segregation degree. Back extrusion at very high shear rates provided via a Drop Extruder Apparatus capable of displacing ram at speeds in excess of 1m/s results in production of very homogeneous products in... 

Effort was made to characterise segregation tendency of mechanically stirred ZA27 alloy with back extrusion as a thixoforming process. At sufficiently high ram speeds, at which liquid phase flows forcefully, pooling of the heavy liquid phase owing to gravitational segregation contributes to homogeneity of back extruded products in terms of solid phase distribution, The amount of this contribution depends on the contact time of this liquid with solid skeleton during liquid exertion to the clearance. Hence, at high ram speeds, small rams which demand taller initial slugs are more efficient in minimising the segregation. However, in the case of low speed back extrusion tests, liquid impotency... 

A high-quality butt joint of aluminum to copper (Al/Cu) can rarely be achieved by conventional fusion and solid-state welding processes. In this research, the appropriateness of friction stir welding (FSW) for making high-quality Al/Cu welds was studied. A sound Al/Cu butt joint was achieved with relatively high strength in uni-axial tensile tests. Mechanical properties and microstructure of the sound friction stir welds were examined. The ultimate tensile strength of the joints reached about 75 percent of the aluminum base metal, with the fracture occurring at aluminum side. The metallurgical study of the welds before and after their failure in tensile tests showed that the heat affected... 

Controlling dynamic biped robots is a complex challenge. Almost all researches in this field assume that the internal structure and dynamics of the robot is known to the controller. But in real-world problems we don't have exact model of the robot or this model is very complicated and is not useful in real-time control. As a matter of fact, we use many devices without any knowledge about their internal structure or analytical models. Some researchers used learning algorithms to control bipeds, but their performance is not comparable to human's learning. Fuzzy controllers can control the bipeds with lower cost, but they need sufficient rules. In the previous works we proposed a linguistic... 

Background: Diabetes is associated with many pathological changes and one of the most important consequences of the diabetes is hepatic injury. The present study was performed to investigate the effect of eight weeks endurance training with consumption of cinnamon supplementation on plasma concentrations of liver enzymes,alanine aminotransferase (ALT) and aspartate aminotransferase (AST) in women with type II diabetes. Methods: In this quasi-experimental study,36 female volunteers with type II diabetes (age 52.72±2.64 years and body mass index 29.28±2.94 Kg/m2) were participated. The subjects were homogenized regarding their body mass index and then were divided randomly into four groups... 

A method for joining metals in the semisolid state is presented. A model alloy Sn-15%Pb was used to demonstrate the concept. By presented process, dendritic microstructure of the weld zone can be avoided. Moreover, near-weld zone of the cold worked substrates which is affected by heat would have a globular structure due to a thermomechanical treatment. The two substrates were heated up locally in the joint line to the semisolid temperature range. At this point a stirrer was introduced into the weld seam in order to mix the two sides into a single uniform joint. Localized mechanical properties of different zones were examined using Shear Punch Test (SPT), showing a good strength in the weld... 

The influence of different parameters such as welding pressure, rotational speed, and traverse speed on the weld properties has been evaluated earlier but there are some important parameters yet to be thoroughly investigated. In this study, an effort has been made to determine the influence of different ratios of rotational speed/traverse speed on mechanical properties of different zones of friction stir welded AZ31 magnesium alloy. Mechanical properties of different zones were determined by a shear punch test. It was found out that increasing the aforementioned ratio leads to a slight decrease in yield and ultimate strength of the stir zone and the transitional zone. It was also observed... 

Seismic isolators are used to decrease the energy and forces of earthquakes. The weight of conventional steel-reinforced elastomeric isolators (SREIs) is high, mostly due to the use of multiple steel shim plates. On the contrary, the damping ratio of SREIs is relatively low. Accordingly, this research utilizes a new approach in which the steel shim plates are replaced by carbon and polyamide fibers. This study attempts to obtain the dynamic and mechanical properties of such carbon fiber- and polyamide fiber-reinforced elastomeric isolators, in comparison with SREIs. In this work, a number of specimens were initially designed and manufactured. Afterwards, compression and cyclic shear tests... 

A size-dependent, explicit formulation for coupled thermoelasticity addressing a Timoshenko microbeam is derived in this study. This novel model combines modified couple stresses and non-Fourier heat conduction to capture size effects in the microscale. To this purpose, a length-scale parameter as square root of the ratio of curvature modulus to shear modulus and a thermal relaxation time as the phase lag of heat flux vector are considered for predicting the thermomechanical behavior in a microscale device accurately. Governing equations and boundary conditions of motion are obtained simultaneously through variational formulation based on Hamilton's principle. As for case study, the model is... 

Functionally graded materials (FGMs) have been introduced to significantly reduce the temperature and thermal stresses on structures at severe thermal loading. Design and development of FGMs as the heat treatable and energy-absorbing materials for high-temperature and thermal protection systems requires understanding of exact temperature and thermal stress distribution, in order to optimize their resistance to failure. In this study, transient temperature and associated thermal stresses in a functionally graded slab symmetrically heated on both sides are determined by separation of the variables scheme. This method is applied to the heat conduction equation in terms of heat flux for... 

Elastomeric bearings are becoming a preferred device for isolating bridges, buildings, and sensitive equipment structures. The technical specifications used to procure these isolators are considered as important factors for the consumers. Lack of communication between structural engineers and rubber technologists, causes structural engineers have slight understanding of rubber properties. In the present study, a number of compounds were initially designed and manufactured, based on a previously studied and manufactured isolator compound. The outcome of the experiments indicated the physical and mechanical properties. Afterwards, the targeted improvement led to modification of the compounds... 

Background: One of the negative effects of cardiac sympathetic hyperactivity is pathologic hypertrophy. Recent studies have indicated that large tumor suppressor (LATS) is one of the molecules which play a critical role in cardiomyocyte apoptosis. Considering the preventive role of exercise training, we evaluated the effects of endurance training on LATS gene expression and its upstream pathway in the present study. Methods: Eighteen male Wistar rats were randomly divided into 2 groups: Endurance and control. Endurance training was performed for 8 weeks, 1 hour per day, and 6 days per week on the treadmill at a 15° inclination. Pathologic hypertrophy was induced with the injection of 3... 

Friction Stir Welding (FSW) is a novel solid state welding process for joining materials. In this process a high speed tool is introduced into the weld seam and due to localized frictional heat, plastic deformation and transverse movement along the weld seam, joining is accomplished. In this study aluminum matrix composite A356 + 15%SiCp is chosen for friction stir welding. Fragmentation of SiC particles and silicon needles existing in eutectic phase as well as their homogenous distribution as a result of stirring with high plastic strains, improve mechanical properties such as modulus of elasticity, yield and ultimate strength, elongation and hardness in the weld zone compared to that of...