Sharif Digital Repository

This article describes a study on WC–10Co cemented carbides with different percent of grain growth inhibitors. Samples were prepared by the conventional powder metallurgy method, using WC and Co powder and different concentrations of VC and (Ta, Nb)C powder. All samples were processed using a hot isostatic press (HIP) and the effect of grain growth inhibitors on the microstructure and mechanical properties were investigated. Additionally, microstructure and powder particle morphology were examined using scanning electron microscopy (SEM) and electron dispersive spectroscopy (EDS). The specimen's microstructure proved that the addition of VC is more effective at suppressing grain growth than... 

This article describes a study on WC-10Co cemented carbides with different percent of grain growth inhibitors. Samples were prepared by the conventional powder metallurgy method, using WC and Co powder and different concentrations of VC and (Ta, Nb)C powder. All samples were processed using a hot isostatic press (HIP) and the effect of grain growth inhibitors on the microstructure and mechanical properties were investigated. Additionally, microstructure and powder particle morphology were examined using scanning electron microscopy (SEM) and electron dispersive spectroscopy (EDS). The specimen's microstructure proved that the addition of VC is more effective at suppressing grain growth than... 

In the present study, the wear behaviour of Cu-Al2O3 composites and Cu-Al alloys has been investigated. The experiment involved casting of Cu-Al alloys with 0•37, 1, 2 and 3 wt-% of aluminium under inert gas atmosphere. The composites were produced by internal oxidation of alloys at 950°C for 10 h in presence of Fe2O3 and Al 2O3 powders mixture. The microstructures of composites were studied using SEM and atomic force microscopy. To identify wear behaviour of specimens, dry sliding pin-on-disk wear tests were conducted according to ASTM G99-95a standard. The normal loads of 20, 30, and 40 N were applied on specimens during wear tests. The sliding speed and distances were selected as 0•5 m... 

The internal Oxidation introduces a practical method for producing copper matrix composites reinforced by alumina particles. The mechanical and physical properties of alumina reinforced copper composites and alloy specimens were investigated. This experiment involves casting of Cu-Al alloys with 0.37, 1, 2 and 3 weight percent of aluminium in non-oxidizing atmosphere with pure oxygen free copper. The composite specimens produced after internal oxidation process at 950°C for 10 hours in sealed alumina crucible. The microstructures of composite specimens were studied after internal oxidation using SEM and AFM. The hardness and electrical resistivity tests were measured. The wear properties of... 

In this paper, we study theoretically the generation of high repetition rate short pulses using fiber optical parametric amplification. We show that the pulse shape and duration depend on the signal location relatively to the pump frequency. We demonstrate that in order to get the shortest pulse width, the signal must be located at one of the extremities of the gain spectrum associated with the pump peak power. We derive the analytical expression of the pulse shape in this case and compare it to the exponential gain regime case. Using numerical simulations, we also analyze the impact of walk-off and pump phase modulation that is required to suppress Stimulated Brillouin Scattering and derive... 

This paper reports a polarization controllable and angle-insensitive perfect metamaterial absorber (PMA). The proposed PMA consists of periodically arranged asymmetric omega-shaped resonators made of metallic copper. The absorptivity was analyzed considering the microwave C-band from 4 GHz to 8 GHz. The proposed PMA shows an absorption peak with almost 100% absorptivity at 6.2 GHz. Also, wideband negative index of refraction is observed. Further, the absorber is inspected for the different rotation angles of the top metasurface (omega-shaped ring) along the optical axis, and obliquity of incidence angle for both TE and TM polarized waves. Moreover, surface electric field and surface current... 

Recent research efforts were made to investigate botanical bactericides as an intervention tool for citrus canker. Five botanical extracts (Eruca vesicaria, Eucalyptus globulus, Trigonella foenum-graecum, Nigella sativa, and Citrullus colocynthis) were evaluated at three different concentrations (0.25%, 0.5%, and 0.75%) against Xanthomonas citri pv. citri under in vitro conditions. Among all treatments, two effective plant extracts, alone and in combinations, were assessed at three different time points (7 days, 14 days, 21 days) under greenhouse conditions. In vitro and greenhouse experiments were conducted under a Completely Randomized Design. Results showed that C. colocynthis expressed... 

In cloud computing, services play key roles. Services are well defined and autonomous components. Nowadays, the demand of using Fuzzy inference as a service is increasing in the domain of complex and critical systems. In such systems, along with the development of the software, the cost of detecting and fixing software defects increases. Therefore, using formal methods, which provide clear, concise, and mathematical interpretation of the system, is crucial for the design of these Fuzzy systems. To obtain this goal, we introduce the Fuzzy Inference Cloud Service (FICS) and propose a novel discipline for formal modeling of the FICS. The FICS provides the service of Fuzzy inference to the... 

The mixed nano-ferrites materials Cu0.6Zn0.4HoxFe2−xO4 (0.00 ≤ x ≤ 0.12) were prepared via the sol–gel auto combustion technique. The TGA curve established the annealing temperature (500 °C) for phase formation. The single exothermic peak on the DSC plot occurred at 341 °C temperature. XRD patterns of these nano ferrites verified single phase formation of the FCC cubic structure. The lattice constant a was increased from 8.4244 to 8.4419 Å and then its value decreased to 8.4319 Å. Crystallite size was found in the range of 7 to 16 nm. The surface morphology of the samples was observed from the scanning electron microscope (SEM) images. The grain size was found within the range of 90 nm to... 

The mixed nano-ferrites materials Cu0.6Zn0.4HoxFe2−xO4 (0.00 ≤ x ≤ 0.12) were prepared via the sol–gel auto combustion technique. The TGA curve established the annealing temperature (500 °C) for phase formation. The single exothermic peak on the DSC plot occurred at 341 °C temperature. XRD patterns of these nano ferrites verified single phase formation of the FCC cubic structure. The lattice constant a was increased from 8.4244 to 8.4419 Å and then its value decreased to 8.4319 Å. Crystallite size was found in the range of 7 to 16 nm. The surface morphology of the samples was observed from the scanning electron microscope (SEM) images. The grain size was found within the range of 90 nm to... 

In the study presented herein, a simple method for laboratory calcite cementation of a reconstituted gravelly sand was presented. This method was used to prepare cemented gravelly sand specimens, which have similar natural characteristics to alluvial deposit of the city of Tehran. The formation and distribution of calcite bonds, as well as the effectiveness of the presented calcite cementation method in increasing interparticle cohesion, as observed in weakly to moderately cemented soil in Tehran, were evaluated by means of chemical analysis, X-ray diffraction technique, and unconfined compressive strength tests. The cementation technique was used to prepare triaxial specimens with calcite... 

Machine-to-Machine (M2M) communication is an important type of communication in the Internet-of-Things (IoT). How to send data in these high-density communications using relay selection can help improve the performance of this type of communication in various applications. In addition, the possibility of simultaneous use of different Radio Frequency (RF) interfaces helps to use the spectrum more efficiently. In this work, we try to further use machine communication RF equipment and improve the average data rate of networks in some applications such as the IoT, which have their own bandwidth requirements. Therefore, we provide an optimization algorithm for relay selection as well as the... 

The development of new technologies has confronted the entire domain of science and industry with issues of big data's scalability as well as its integration with the purpose of forecasting analytics in its life cycle. In predictive analytics, the forecast of near-future and recent past - or in other words, the now-casting - is the continuous study of real-time events and constantly updated where it considers eventuality. So, it is necessary to consider the highly data-driven technologies and to use new methods of analysis, like machine learning and visualization tools, with the ability of interaction and connection to different data resources with varieties of data regarding the type of big... 

Norouzak oil seeds that are the source of bio-diesel (Norouzak) fuel grow mostly in Gonabad and Kashmar located in Khorasan, north east of Iran. Spray characteristics of Norouzak bio-diesel have been experimentally and theoretically studied in this work. Norouzak fuel is added to the conventional diesel fuel, and mixture formations of several blends have been investigated and compared with each other. Moreover, by varying ambient and injection conditions, behaviors of spray of different blends have been explored. Microscopic and macroscopic properties of spray such as Sauter Mean Diameter (SMD), Ohnesorge number, spray tip penetration, spray cone angle, spray projected area and volume have... 

Norouzak oil seeds that are the source of bio-diesel (Norouzak) fuel grow mostly in Gonabad and Kashmar located in Khorasan, north east of Iran. Spray characteristics of Norouzak bio-diesel have been experimentally and theoretically studied in this work. Norouzak fuel is added to the conventional diesel fuel, and mixture formations of several blends have been investigated and compared with each other. Moreover, by varying ambient and injection conditions, behaviors of spray of different blends have been explored. Microscopic and macroscopic properties of spray such as Sauter Mean Diameter (SMD), Ohnesorge number, spray tip penetration, spray cone angle, spray projected area and volume have... 

In the present work, the spray characteristics of bio-ethanol and its blends have been experimentally and theoretically investigated. To have a comprehensive study, the effects of ambient condition and injection pressure on the spray of different blends have been considered. Macroscopic and microscopic characteristics of spray such as tip penetration length, cone angle, projected area, volume, Sauter Mean Diameter (SMD), and Ohnesorge number are investigated precisely. Besides, air entrainment and atomization analyses have been carried out to improve mixture formation process. Using curve fitting and least squares method, theoretical correlations have been suggested in such a way to predict... 

The viscoelastic properties of bone significantly influence the mechanical stability of bone-screw complex. This study aims to evaluate the changes in stiffness of a bone-screw model under different bending displacements and pre-stress conditions over time. Using a finite element model, we applied bending displacements of 12,24, and 48 μm were applied to the head of the screw. The stiffness was predicted at time intervals of 1,61,121, and 181 seconds to assess the impact of stress relaxation. The bone was modeled with viscoelastic properties, and the screw was considered rigid. The results showed a decrease in stiffness with increasing displacement. At 12 μ m, the initial stiffness was... 

Process lifecycle has several stages, including process design covered in multiple stages. Process economics is a vital factor in finalizing the process design. Besides economics, inherent safety is an important concept contributing to sustainable process design generation. The inherent safety concept has been applied via equipment characteristics for individual equipment. Since a method considering inherent safety with equipment aspects and process economics has not been available, therefore, a new method has been proposed, namely sustainable process design for heat exchanger network (SPDHEN), to integrate inherent safety, equipment aspects, and process economics. SPDHEN uses indexing to... 

Objective: To determine the motor-behavioral and neural correlates of putative functional common variants in the sodium-channel NaV1.8 encoding gene (SCN10A) in vivo in patients with multiple sclerosis (MS). Methods: We recruited 161 patients with relapsing-onset MS and 94 demographically comparable healthy participants. All patients with MS underwent structural MRI and clinical examinations (Expanded Disability Status Scale [EDSS] and Multiple Sclerosis Functional Composite [MSFC]). Whole-brain voxel-wise and cerebellar volumetry were performed to assess differences in regional brain volumes between genotype groups. Resting-state fMRI was acquired from 62 patients with MS to evaluate... 

As firms are facing with a new competitive environment which knowledge has a unique position, they should give more consideration to their employer's knowledge, and construction firms are not an exception. Employers are creating values for companies, and nowadays they are counted as strategic resources. In construction firms, due to their project based nature, workers are more important in creating values. One of the most essential elements of a construction firm is its ability to cope with social and environmental pressures to reduce waste and minimise the use of raw materials. To decrease wastes of Steel structure Construction, it is necessary to enhance the weld quality. Weld quality...