Sharif Digital Repository

This paper presents a surface generation model for sculptured surface productions using the ball end milling process. Dimensional measurement using a coordinate measuring machine (CMM) has been commonly adapted in advanced manufacturing environment to ensure that manufacturing products have high quality and reliability. To conduct dimensional inspection efficiency in a computer integrated manufacturing (CIM) environment, there is an urgent need to derive a sampling strategy which can be used to specify a set of measuring points that lead to accurate sampling while minimizing the sampling time and cost. Owing to the variations in characteristics of geometric feature and manufacturing process,... 

For many years of tall buildings with regard to the development and progress towns are necessary for the urbanite of the city and are considered as progress of the symbols societies. These buildings because of high wore their features special treatment under the influence lateral loads like the earthquake. In a way that today is an important issue in seismology and Earthquake Engineering all the powerful movements of the earth and its effect on the performance of the workforce special buildings as tall. Two points in this important subject. First modeling and simulations of the Most Powerful Earthquakes that in general occur in the field of near source earthquake generator. The earthquake of... 

In this study, membrane distillation process was used for treatment of high salinity waters. The focus of this study is to simulate and build a setup of membrane distillation process. Since the membrane distillation process is based on the driving force of the temperature difference, the required temperature is provided by both the use of heaters and the use of solar energy. To increase the feed temperature by solar energy, a black polymer coating on the main membrane is used. The main membrane used in this process is PVDF polymer and the polymer coated on the surface is the PAN polymer. After simulating and constructing the laboratory setup, the influence of a variety of parameters on the... 

FGM sheets with component or grain size gradient in their thickness direction provide mechanical and physical gradient properties through ND direction. FGMs are fabricated by various methods including centrifugal casting, powder metallurgy, PVD and CVD,all of which suffer from some shortcomings such as porosity of the products, low rate and high cost of production and restrictions on mass production. In this study, 2 and 4 layered Al matrix FGM sheets containing SiC and Al2O3 powders were fabricated by laminating method of Accumulative Roll Bonding(ARB). Two approaches of stacking were chosen as accumulative coupled roll bonding (ACRB) and (ASRB) for initial roll bonding and subsequent... 

Metal matrix composites (MMC) and metal foams (MF) have been the topic of numerous researches during the last decades. The appropriate mechanical and physical properties of these materials make them useful in various industries. In this research, a unique approach is introduced for producing MMCs and MFs in which accumulative roll bonding (ARB) is employed in order to achieve a homogeneous distribution of ceramic particles in the metal matrix. Also, foamed structures can be made by subjecting Al/TiH2 composite to an appropriate annealing heat treatment where TiH2 particles decompose to hydrogen and titanium. In this work, the effect of number of ARB cycles on the size and distribution of... 

This project examines four alternatives such as pipelines, oil injection wells, LNG & GTL in the purpose of Iran gas utilization. In this Project four strategies using cost/benefit analysis are examined. For this purpose, at first the cost of inlet feed gas per Mmbtu are calculated. Then regarding various scenarios of average world gas prices for the following thirty years, the cost & benefit of any way will be counted. Then with the use of energy security, the project will make energy policy. For this purpose, Shannon indicator will be used as one of the most reliable indicators. Due to the of use this indicator, the popular project will be chosen accordingly as a certain amount of gas the... 

Climate change and energy security are key drivers for future energy policy. While energy security has been a pillar of energy policy for about a century, concern about climate change is more recent and is bound to radically change the landscape of energy policy. Policy makers are now under increasing pressure to address these twin challenges: to develop cost-effective policies that will both ensure the security of our energy system and reduce greenhouse gas emissions.
Main Effort in this Project is to construct an integrated model of Iran’s energy system to serve as a policy analysis tool, by which policymakers are able to identify the future effects of a wide range of policies in... 

Dependence of some magnetic properties such as core loss and permeability on temper rolling was studied in this thesis. It is shown that with a proper temper rolling sharper textures are obtained in the electrical steel and the magnetic properties in the longitudinal and traverse directions are improved. By texture analysis, it is shown that because of temper rolling, shear strain on the surface of the sheet is the main factor for abnormal grain growth and shear texture formation on the surface. The result of formation of this texture is enhancement of the {100} intensity and reduction of the {111} intensity, leading to the improvement of the permeability. Temper rolling is always... 

Based on International Energy Agency studies, achievement of 450 ppm CO2-equivalent emission target in global emission means that the CO2 emissions in 2050 must be reduced to %50 of 2005 level, and this implies that a portfolio of emission reduction policies and strategies need to be exploited through current century.
At the present time, Carbon Capture and Storage (CCS) Technology is a dominant strategy among all the long-term carbon abatement strategies in many countries. Nevertheless, its potential as a climate mitigating option will be proved, only if it is implemented in the countries which are developing at a great pace and taking advantage of fossil fuels in order to afford their... 

Lipid membranes are fundamental constituents of cell membranes and are now used in lap-on-a-chip technology. Membranes in living cells contain a significant fraction of proteins, which undergo lateral random movements due to thermal fluctuations and shear forces imposed by the solvent fluid. Prominent natural and biotechnological systems where membranes are highly sheared include the plasma membrane of endothelial cells, and membranes used in biosensors for high throughput screening of drug candidates, and in water purification devices. In these systems membrane is in direct contact with the mainstream suspension flow, which is driven by pressure gradients. The efficiency and function of... 

Splitting in ingot cast structures and transverse cracks in continuous cast structures are the main problems of hot rolling of low carbon resulfurized free-cutting (LCRF) steels. Presence of high volume fraction of manganese sulfide inclusions in cast structure increases the risk of alligatoring in hot rolling. Because of high sulfur content of these steels and probability of formation of low melting point phases, minimum level of manganese and maximum level of copper and tin is necessary. Morphology of manganese sulfide is another important factor in hot forming of these steels, which can be controlled by level of deoxidation in steel making. In fact, MnS2 is present in fully killed... 

Particle reinforced aluminum matrix composites have considerable attraction in automotive and aerospace industries due to their special properties as light weight, high ratio of strength/density, improved elastic modulus, low coefficient of thermal expansion and high wear and corrosion resistance. Among the production processes of metal matrix composites, accumulative roll bonding process has particular importance due to producing ultrafine grained composite sheets. However, uncontrolled and undesired agglomeration of particles is the main problem in producing these composites. In this research, the Al2O3 and SiC nanoparticles were electrostatically stabilized against agglomeration by... 

In this project a model for the analysis and assessment of gas transit in the Caspian Sea and its effects on the desired benefits of the approach of decision-making, has been developed.
The first comprehensive review of the supply and demand of gas in the world and the countries of the Caspian region and the cast has been affecting world energy developments.After a comprehensive analysis of the status of the gas transit routes from the Caspian region and provided. Then, using the Delphi method and elite views the main criteria related to gas transit and affecting the interests of the countries of the Caspian region to determine the detailed criteria for each main criterion was determined... 

Distributed generation (DG) and its utilization have some benefits and risks for its owner and power network. From owner perspective, benefits of DG include selling energy, reducing costs related to fuel, and other economic benefits. However, there are some risk factors for the owner including risk of supplying fuel, risk of selling generated power, and other risk factors related to establishment of the DG unit. Utilizing risk-reduction tools such as signing agreements for selling power, purchasing fuel, and related economic tools are necessary for risk management of the owners of DG units. The purpose of this thesis is to investigate the economic situation of the DG units and optimize the...