Sharif Digital Repository

In this research, Synthesis, characterization and photoelectrochemical application of two dimensional MoS2 and WS2 nanosheets have been carefully investigated. And finally, based on theoritical and experimental analysis results, the mechanisms of the observed photoelectrochemical (PEC) activities were suggested.The ab initio density functional calculations about Mo1-xWxS2 monolayer deposited over a TiO2 (110) substrate revealed a shift in band position of the Mo1-xWxS2 in favor of photoelectrochemical water splitting. Moreover, increase of W concentration in Mo1-xWxS2 could improve the charge separation and increase the effective mass ratio leading to an extension of the electron–hole... 

Fighting contagious microbial diseases is considered a serious health issue, which has attracted much attention in worldwide. Thus, development of new materials based on nanostructures as a new generation of antibiotics to address this challenge has been of interest to researchers in recent years. Nanostructures based on metallic oxide semiconductors such as oxides with light absorption, production of electron-hole pairs in needle like structures cause tearing bacterial membrane and eventually destroy the bacterium. To this end, we designed experiments to study mechanism and physics governing the process of bacterial degradation to determine the best conditions for inhibiting bacteria... 

Different molybdenum oxide nano/micro structure thin films were synthesized by thermal evaporation method under various growth conditions such as deposition time, temperature and evaporation source-substrate distance. Molybdenum oxide nanostructures grown on Si(100) such as nanowalls, nanostars and nanowires were characterized with scanning electron microscopy (SEM), x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD), atomic force microscopy (AFM) and high resolution transmission electron microscopy (HRTEM). Shape and type of nanostructures were determined with SEM, AFM and HRTEM analysis. XPS analysis showed that the synthesized nanostructures contained Mo6+, Mo5+, Mo4+ and... 

Synthesis, characterization and photocatalytic applications of core-shell like ZnO@CdS nanorods have been studied in this research. The synthesis of core-shell like ZnO@CdS nanorods was carried out in three different steps. At first, ZnO seed layer was formed on glass substrate via sol-gel process under optimum conditions using absolute ethanol solution containing zinc acetate and a stabilizer ( either Monoethanolamine (MEA) or diethanolamine (DEA)). When MEA used as stabilizer, the optimum concentration of sol was found 0.2 M, while increasing the sol concentration caused the seed layer to be grown in a string-like structure. The RMS surface roughness of seed layer prepared by 0.2 M sol... 

Because of the working conditions of semiconductors at ambient temperature and pressure, degradation of organic pollutants through semiconductors photocatalysis has attracted the interest of many researchers. Because of its large exciton binding energy,high chemical and physical stability,high electron and hole mobility, and low cost; zinc oxide, an n-type semiconductor with 3.2 eV direct band gap, is widely used in applications such as photocatalysts, solar cells, and light-emitting diodes. Among various morphologies of ZnO, 1D nanostructures such as nanowires and nanorods have recieved much attention due to their high surface to volume ratio. However, the application of ZnO as a... 

ZnO is a wide and direct band gap (3.37 eV) semiconducting material with a large exciton binding energy (60 meV). It has been extensively studied in the last few years owing to its potential applications in various fields such as surface acoustic wave devices (SAW), transparent electrode, solar cell windows, photovoltaic devices, gas sensors and photoelectrochemical cells. Recently, much attention has been paid to rare-earth (RE) doped ZnO for possible applications in visible emitting phosphors in displays, high power lasers, and other optoelectronic devices. In this thesis, initially ZnO thin films were deposited on glass and ITO substrates using sol-gel dip-coating method. Optical and... 

hydrogen considered as one of clean energy carriers and is the most promising alternative to fossil fuels. The production of hydrogen from photoelectrochemical water splitting using titanium dioxide nanotubes arrays (TNA) as a photoanode has been of interest to many researchers in recent years. In this study, TNAs were fabricated with two-step anodic oxidation method at a constant applied voltage of 60 V DC. The fabrication process was performed for duration time of 1, 2, 3, 4 and 5 hours. Photoelectrochemical analysis for the fabricated samples shows that TNA prepared for 3 hours anodic oxidation time exhibited the highest current density of 1 mA.cm-2 at 0.5 V bias voltage (Optimized... 

In this research, two type of graphene quantum dots (GQDs) have synthesized including, normal GQDs and nitrogen-doped GQDs (N-GQDs). Then, each of GQDs were deposited on the 1 dimensional zinc oxide (ZnO) nanostructures namely nanowires (NWs) and branched hierarchical (BH) systems. Then, photocatalytic activity of the samples were studied in photodegradation of methylene blue (MB) and methylene orange (MO) under visible light. First, ZnO nanowires (ZnO NWs) were fabricated by anodization of zinc sheet possessing wurtzite crystal structure with their average length and diameter measured in the range of 50-60 μm and 170-300 nm, respectively. Then, normal GQDs were synthesized by... 

WO3 have good electrochromic, gas sensor, photocatalyst, phoelectrochemical (PEC) properties. due its properties, tungsten oxide have many application in technology and industry. In this thesis, pure WO3 thin film and MWCNT-WO3 nanocomposite thin films with different weight percent of MWCNT/WO3 utilize for energy domain, particular hydrogen production with phoelectrochemical reactions spiliting water. For this purpose, initially WO3 thin films were deposited on glass and ITO substrates using sol-gel dip-coating method. Optical and surface properties of the films dried at 100ºC and annealed at 400 ºC had been investigated. UV-Visible spectrophotometer, atomic force microscopy (AFM), X-ray... 

World population growth, depletion of fossil fuels resources depletion and increased air pollution resulting from their consumption, human society has had to replace fossil fuels with renewable sources. In this context, the production of hydrogen using solar energy is feasible candidate to replace fossil fuels, which can be produced by water splitting in a photoelectrochemical (PEC) cell using an appropriate photocatalyst. This clean production method has been attended by many researchers in recent years. The most common photocatalyst for the conversion of sunlight to hydrogen by splitting water is Titanium dioxide (TiO2). But high energy gap and fast electron-hole recombination rate in TiO2... 

Ammonia (NH3) is the second most synthesized chemical in the world which is used about 80% for the production of chemical fertilizers. Industrial production of ammonia commonly relies on Haber-Bosch method that is produced from gaseous N2 and H2, at very high pressure (200-400 atm) and high temperature (400-600oC) on the surface of an iron-based catalyst. But due to required high pressure and temperature researchers are looking for alternative methods that are environmentally friendly. In this research, we applied electrochemical nitrogen reduction reaction (NRR) used nickel oxide (NiO) deposited on nickel foam substrate by hydrothermal method. The prepared samples were treated by nitrogen... 

In this project, the photoelectrochemical properties of ZnO nanostructures modified by CdS and Graphene was studied. Firs, titanium foil was cut into rectangular shape with 1cm width and 3 cm length, cleaned by rinsing in acetone and ethanol and annealed at 4000C for an hour. As a result, a thin layer of titanium oxide was formed on Ti sheet. Then a layer of grapheme oxide was deposited on substrate using Electrophoretic deposition (EPD). After that, ZnO nanostructure was deposited on the TiO2 substrate using Electropulsation (EP) with 20 consecutive pulse followed by 3 minutes Electrodeposition (ED). Using SEM analysis, the morphology of ZnO was determined to be nanopetals in which the...