Sharif Digital Repository

An efficient algorithm for the design optimization of the compressible fluid flow problem through a flexible structure is presented. The methodology has three essential parts: first the behavior of compressible flow in a supersonic diffuser was studied numerically in quasi-one-dimensional form using a flux splitting method. Second, a fully coupled sequential iterative procedure was used to solve the steady state aeroelastic problem of a flexible wall diffuser. Finally, a robust Genetic Algorithm was implemented and used to calculate the optimum shape of the flexible wall diffuser for a prescribed pressure distribution. © 2006 Elsevier Ltd. All rights reserved  

In this paper, the compressible gas flow through a pipe subjected to wall heat flux in unsteady condition in the entrance region is investigated numerically. The coupled conservation equations governing turbulent compressible viscous flow in the developing region of a pipe are solved numerically under different thermal boundary conditions. The numerical procedure is a finite-volume-based finite-element method applied to unstructured grids. The convection terms are discretized by the well-defined Roe method, whereas the diffusion terms are discretized by a Galerkin finite-element formulation. The temporal terms are evaluated based on an explicit fourth-order Runge-Kutta scheme. The effect of... 

The authors' research work on pressure drop along gas transmission pipelines raised questions regarding the development length of the corresponding compressible flow and the effect of heat transfer in the entrance region on the pressure drop along the whole length of the pipe. In this paper, laminar, viscous, compressible flow in the entrance region of a pipe is investigated numerically in two dimensions. The numerical procedure is a finite-volume based finite-element method applied on unstructured grids. This combination together with a new method applied for boundary conditions allows accurate computation of the variables in the entrance region. The method is applied to some incompressible... 

The wellhead flow control valve bodies which are the focal point of this failure case study were installed in some of the upstream facilities of Khangiran's sour gas wells. These valve bodies have been operating satisfactorily for 3 years in wet H2S environment before some pits and cracks were detected in all of them during the periodical technical inspections. One failed valve body was investigated by chemical and microstructural analytical techniques to find out the failure cause and provide preventive measures. The valve body alloy was A216-WCC cast carbon steel. During investigation many cracks were observed on the inner surface of the valve body grown from the surface pits. The results... 

Local annealing of amorphous NiTi thin films was performed by using an Nd:YAG 1064 nm wavelength pulsed laser beam. Raw samples produced by simultaneous sputter deposition from elemental Ni and Ti targets onto unheated Si (100) and Silica (111) substrates were used for annealing. Delicate treatment with 15.92 W/mm2 power density resulted in crystallization of small spots; while 16.52 and 17.51 W/mm2 power densities caused ablation of the amorphous layer. Optical microscopy, scanning electron microscopy, X-ray diffraction and atomic force microscopy were performed to characterize the microstructure and surface morphology of the amorphous/crystallized spot patterns  

With the significant role that warehouse plays in connection to suppliers, distributors, and clients, and considering the costliness of storage systems, efforts have focused on the reduction of procedural expenses. Among the most significant expenses, one involves the distance traveled by operators or S/R machinery for the selection of ordered items; the common solution to which has been through the classification of stored items. Previous articles have focused on linear solutions to the abovementioned problem, such as P-Median. This article shall focus on the problems arising from the said solution, and instead a non-linear method proposed. Further, a heuristic algorithm is produced for the... 

The wellhead flow control valve bodies which are the focal point of this failure case study were installed in some of the upstream facilities of Khangiran's sour gas wells. These valve bodies have been operating satisfactorily for 3 years in wet H2S environment before some pits and cracks were detected in all of them during the periodical technical inspections. One failed valve body was investigated by chemical and microstructural analytical techniques to find out the failure cause and provide preventive measures. The valve body alloy was A216-WCC cast carbon steel. During investigation many cracks were observed on the inner surface of the valve body grown from the surface pits. The results... 

Veronica genus (Plantaginaceae) is broadly distributed in different habitats. In this study, the inhibitory activity of free soluble and conjugated phenolic extracts of Veronica persica on key enzymes associated to type 2 diabetes (α-glucosidase and α-amylase) and hypertension (angiotensin I converting enzyme, ACE) was assessed, as well as their antioxidant power. Our results showed that both the extracts inhibited α-amylase, α-glucosidase and ACE in a dose-dependent manner. In particular, free phenolic extract significantly (P < 0.05) inhibited α-glucosidase (IC50 532.97 μg/mL), whereas conjugated phenolic extract significantly (P < 0.05) inhibited a-amylase (IC50 489.73 μg/mL) and ACE... 

Gait training is a critical rehabilitation procedure for patients suffering from walking problems. It, however, puts the therapist in high orthopedic risk since he should prevent the patient from possible falling. Body weight support system is a new technology helping such patients and the involved therapist by unloading a percent of the patient's weight. A new over-ground body weight support is introduced in this article. The system is composed of two main modules namely unloading and traction. The unloading module is capable of suspending an individual's weight up to 1000N dynamically. The whole system is attached to an overhead rail, moving over the head of the patient by the traction... 

The failure analysis of a ruptured superheater tube after 20. years service in the oil-fueled boiler, as the typical problems in power plants, was investigated. A thin-lipped rupture at failed region was observed in superheater tube. By measuring the tube's wall thicknesses far from failed region, non-uniformity was seen. The suggested main root cause of failure was fireside corrosion of the tube during the service. Because of low grade of used fuel, sodium, sulfur, and vanadium elements were observed at the outer surface, which caused continuously scale formation and reduction of wall thickness, by metal consumption. In addition, it seems that it has been worsened by occurrence of long-term... 

The preparation of high aspect-ratio TiO2 nanotubes and their photocatalytic activity were demonstrated in this study. The high aspect-ratio TiO2 nanotube thin films were produced by electrochemical anodic oxidation of Ti in chloride-containing electrolytes. Nanotubes were doped with different concentrations of ZnO particles through anodization. The catalytic behavior was evaluated under batch reactor with photo-degradation test of Red Dye. The experimental results collectively demonstrate the successful ZnO doping of the resultant nanotube layers with significant abundant OH groups on their increased surfaces. The nanotubes doped with high content combined with an anatase as a two phase... 

With the rise in oil price and population growth, renewable energies are assumed to be the main source of energies for the next generation. Wind as a natural, eco-friendly and renewable source of energy has been at the center of concentration for decades. Recently there has been some ideas regarding the self-regulating urban wind turbines. Researchers have shown that a proper enclosure increases the wind velocity and therefore more torques can be exerted on the rotors, therefore more power can be generated. These enclosures are light and cheap, therefore they are applicable and effective. In the present study, an enclosure was modified to increase the exerted torque with implementing a step... 

We conduct an experimental investigation on the pool boiling enhancement in DI water on nanoporous surfaces. The surfaces are modified by anodic oxidation, and cavities with 2 mm diameter and pitches between 2.5 and 5 mm applied on them using EDM method filled with a two-part epoxy with low thermal conductivity properties. The capillary wicking action of the superhydrophilic nanoporous oxide layer enhances the rewetting and spreading of the liquid to dry-spots during boiling. The epoxy disks remain wet and prevent merging bubbles during the pool boiling experiment and a 2-D microflow is induced toward dried regions with synergic effects of nanoporous surface absorption, create a considerable... 

There are two types of scatterers in a multipath propagation environment: fixed and non-fixed scatterers. Fixed scatterers like buildings, mountains and tree stems do not move, while non-fixed (moving) scatterers like cars, people and tree leaves move from their initial positions. In addition to different movements of the mobile station (MS) that cause different kinds of Doppler fading, movements of non-fixed scatterers are also anticipated to generate other kinds of fading/correlation. This fading changes depend on the type of the propagation environment and the type of movements of local surrounding scatterers. In this paper we characterize these effects in terms of temporal correlations.... 

In this paper, a private telephone communication network of an electrical energy distribution company has been studied analytically and through discrete event system simulation. Considering the pitfalls and difficulties associated with the analytical approach in designing such a network and the power and performance of a simulation methodology in this regard, a simulation model was developed using GPSS/H simulation language. After data collection and analysis, model development and validation, initial transient study and design of experimental phases, the model was applied to determine the operating performance of the current system, as well as to evaluate the performance of any newly... 

Treatment of dye pollution containing C.I. Acid Red 14 (AR14) by a coupled photocatalytic process was studied. Titanium dioxide, in the form of anatase and rutile, and zinc oxide, were used as photocatalysts. The investigated photocatalysts were Aldrich-produced nanopowders with crystallites of a mean size of 20-30 nm and a specific surface area of about 50 m 2/g. A comparison of TiO 2(anatase), TiO 2(rutile), TiO 2(a,r), and ZnO for the decolorization of the AR14 solution was performed. Results showed that color removal followed the decreasing order of TiO 2(a,r), ZnO > TiO 2(a,r) > TiO 2(a), ZnO > TiO 2(r), ZnO >TiO 2(a,r) > TiO 2(a) > ZnO > TiO 2(r). Response surface methodology (RSM) was... 

In this study, the failure analysis of a shaft of a unit, which had been failed during the service, was studied. This shaft was welded to the blades, and their chemical compositions were determined by spectroscopy method. In order to determine the root cause of failure and contribution factors, different investigation methods including visual examination, optical microscopy and scanning electron microscope analysis, and hardness test were carried out. It was concluded that the shaft was failed due to fatigue. The failure was caused by improper welding of blades to the shaft. At the end, in order to prevent or decelerate such failure, some recommended remedies were suggested  

All costs within the life cycle of a building are known as its life cycle cost (LCC). In the design process of a building, the use of a lower initial cost index to select an option among others with similar performance may not lead to an economically optimal alternative during the life cycle. Hence, today, building designers and investors require a tool to estimate life cycle cost at the conceptual design stage to select an economically efficient option. Resilient solutions generally lead to a higher level of complexity and upfront costs and carry additional embodied environmental impact as well. This study aims to support the design of resilient buildings using a sound LCC methodology in... 

Nowadays, increasing the CO2 emissions are one of the inevitable challenges in the world. In addition, in many industries, fossil fuels are the main source of energy demands which worsen the problem. Since in most applications, the performance and energy loss are highly affected by the drag force, many investigations have been proposed to improve the surface properties to moving surface against the water, and consequently, increasing drag reduction. To this end, one effective way is utilizing superhydrophobic coatings. In this study, we prepare two different superhydrophobic coatings using Al2O3 nanoparticles (NPs) modified by HMDS (1,1,1,3,3,3-Hexamethyldisilazane) and PDMS...