Sharif Digital Repository

Since steady state behavior of a plant is affected by the change of various inputs to the plant, the transient behavior of the chemical plants are also very important in their general performance. On the other hand, catalytic hydrotreating is one of the most important processes in crude oil refining process in many aspects such as economical, technical and environmental. Thus, the goal of this project was dynamic simulation and control of catalytic hydrotreating unit (UNIFINER Unit) of Tehran Refinery with using the HYSYS software. To fulfill this target, data that were necessary for simulation were gathered from Unifiner unit of Tehran refinery at first. Then, steady state simulation of the... 

In this research, carbon nanotubes (CNTs) and CNT coated by titanium dioxide (TiO2) were used as adsorbents for desulfurization. Photocatalytic oxidation by titanium dioxide Degussa P-25 nanoparticles (as photocatalyst) immobilized on a porous and low-density support called “perlite” and CNT/TiO2 was perused. TiO2-coatings were prepared by liquid phase deposition method.This is a wet process for the formation of metal oxide thin films on substrates. The coating of nanotubes with TiO2 was confirmed by IR and EDAX and morphological properties were observed by SEM analysis.The physical properties of adsorbents were determine using BET.Dibenzothiophene (DBT)dissolved in acetonitrile was used as... 

Oxidative desulfurization (ODS) is one of the desulfurization processes that posseses several important advantages such as mild operating conditions. In the present work, oxidative desulfurization of kerosene with a total sulfur content of 2335 ppm and gas oil with a total sulfur content of 7990 ppm were carefully investigated. By evaluation of different oxidation systems, the hydrogen peroxide-formic acid system was selected for the oxidation of sulfur-containing compounds of the light fuel oils. The effects of main operating parameters of the oxidation system including temperature, hydrogen peroxide to sulfur molar ratio (O/S), and formic acid to sulfur molar ratio (Acid/S) on the... 

In past three decades, use of crude oil’s derivatives increased dramatically. The critical environmental condition of today’s world, which majorly caused by unclean fuels, forces governments to legislate new rules to increase quality of fuels. These rules force refinery industries to produce clean fuels. One of the main processes in producing clean fuels is Desulfurization process. For fuel desulfurization there are different kinds of processes like HydroDesulfruization, Oxidative Desulfurization, Bio-desulfurization, etc. From these processes Hydro-desulfurization is the conventional process for desulfurization. Because of significant problems of this process, like high operational cost,... 

In this study, desulfurization of petroleum coke has been investigated for use in aluminum industry. To reduce sulfur content in petroleum coke, desulfurization has been investigated by two methods of solvent extraction and molten caustic leaching. The method of molten caustic leaching at temperatures of 400-600 °C has been investigated. Other effective parameters on the desulfurization of petroleum coke are the mass ratio of alkali to feed (petroleum coke) in the range of 0.5-1.5 and the time of 1-3 hour and the mesh size of 200-600 micron. In this study, the conditions of desulfurization of petroleum coke using potassium hydroxide have been investigated. Results show that by using the... 

Microfluidic is a science and technology in which they study the behavior of fluids, control them and design devices or systems with dimensions of tens to hundreds of micrometers. The technology has the ability to design and manufacture macro-scale and micro-scale equipment, such as micro-pumps, micro-valves, micro-filters, micro-mixers, micro-reactors, and other equipment. The benefits of this technology include the use of low sample size, low waste of energy, low power consumption, short response time, high system performance, portability and performance of several operating phases in a compressed piece such as production, isolation and analysis. Also, the very low amount of chemicals and... 

In this study, the pervaporation method was used for desulfurization of gasoline. Thiophene was used as a sulfur agent and n-heptane as a representative of hydrocarbon compounds in gasoline. The composite membranes of the active PDMS layer containing the UiO-66 metal-organic framework nanoparticles are based on porous membrane PVDF. The effect of adding PVP polymer on the porosity of the PVDF membrane has been investigated. Scanning electron microscopy (SEM), Fourier transform infrared spectrum (FTIR) and X-ray diffraction (XRD) have been used to characterize nanoparticles and synthesized membranes. The effect of adding nanoparticles on the membrane performance and its sowelling effect in... 

There are different sulfur compounds in the crude oil, and after combustion all of these sulfuric compounds produce sulfur dioxide, this sulfur dioxide cause acid rain, deactivation of catalysts and also environmental bad effects. So the amount of sulfur that is released should be controlled and this is done by removing sulfuric compounds before combustion. zeolites as adsorbent of sulfuric compounds has been used widely by researches and had given good results. molecular dynamics simulation as an effective way for describing the behavior of these compounds in the molecular level and in scales of angstrom has been used and the effect of van der waals and electrostatic forces between sorbates... 

In recent years, desulfurization has received much attention due to its devastating environmental effects. The existence of sulfur compounds has effects such as corrosion, poisoning of catalysts, reduction of heat of combustion and reduction of price. Sulfur compounds in hydrocarbon fuels also produce sulfur oxides caused by combustion then they enter the atmosphere, and cause acid rain. Acid rain dissolves building materials, poisons lakes, and destroys forests. Therefore, removing sulfur or converting it to less harmful substances is one of the most important processes in refineries. The method studied in this research is the use of adsorption desulfurization method by microchannel which... 

Due to the increasing consumption of fuel, the use of new methods with high efficiency to remove sulfur from fossil fuels is felt more than ever. Hydrogenation and oxidation of sulfur organic matter, such as thiophenes, is an old method of desulfurization of liquid fuels. Using a photocatalyst, everything can be done in an environment that is very low cost. In this study, the photocatalytic elimination of dibenzothiophene was investigated. For this purpose, carbon-doped thiamine dioxide was used as the photocatalytic base, which is synthesized by hydrothermal method. This method is the same source of titanium and carbon. To increase the performance of the catalyst, platinum metal was loaded... 

Since, presence of sulfur compounds in fuels leads to environmental pollution and deacrese of fuel quality, fuel desulfurization should be considered for enhancing the fuel charachteristics. Electrochemical desulfurization was recogonized as one of desulfurization techniques that uses anode and cathode in an electrolytic environment under mild temperature and pressure. In this research, electrochemical desulfurization of crude gas-oil has been studied over electrodes of copper and stainless steel in the presence of NaOH and sulfuric acid. In this research, the effects of operational prameters like stirring rate, temperature, applied potential, sodium hydroxide/sulfuric acid addition as... 

In recent decades, desulfurization processes have become essential to decrease environmental pollution due to the emission of sulfur from fuels. In this study, in order to desulfurize liquid fuel, a model fuel (normal heptane) was investigated under visible light ) 350-watt sodium lamp(, using H2O2 as oxidant and methanol as a solvent in the presence of Cu-C-TiO2 nanostructure. C-TiO2 was synthesized by the hydrothermal method. In order to modify and improve the properties, we doped the copper metal by impregnation method with different loading of Cu. Experimental results exhibited the highest activity among samples attributed to 0.5% Cu-C-TiO2 Which caused 98.27% degradation of DBT after 2... 

During fuel combustion, aromatic sulfur compounds in energy fuels convert into sulfur oxides, which cause major environmental problems such as acidic rain, global warming, and air pollution. Absorption desulfurization is one of the promising and economical methods to remove these sulfur compounds from fuels. Metal-organic frameworks (MOFs) are a class of nanoporous materials that are of interest for use as adsorbents due to their high specific surface area, unique surface adsorption properties, high adsorption capacity, tunable porosity, flexible dynamic behavior, and diversity in functional and metal groups. In this research, we first synthesized five metal-organic frameworks, namely... 

The selective oxidation of H2S into elemental sulfur is a complementary desulfurization method for reducing H2S emissions from gas streams. Several studies have been conducted in recent years to develop active, selective, and stable catalysts. The purpose of this research is to develop a catalyst with high activity and selectivity that is suitable for the gas output of one of the country's refineries. For this purpose, three supports of mixed metal oxide (solid solution), Ce-Al, Ce-Si, and Ce-Zr with a molar ratio of 1:2 (ceria: metal) were made by the co-precipitation method. In the following, three samples named 10V-CeAl, 10V-CeSi, and 10V-CeZr were prepared by impregnating 10% wt vanadium...