Sharif Digital Repository

The hot deformation characteristics of 7075 aluminum alloy (AA7075) are investigated by means of hot compression tests carried out in the temperature range of 200-450 C and strain rate range of 0.0003-1 s-1. Two novel processing maps based on flow localization parameter and enhanced DMM are developed and compared with conventional DMM results. It is observed that processing maps based on flow localization parameter can be used successfully to predict AA7075 thermomechanical behavior. Also, the comparison of the DMM results indicates that the new approach to calculate DMM power dissipation efficiency and instability criteria corresponds better with experimental observations. The occurrence of... 

A new integrated physically based constitutive model was developed for an age hardenable Al- Mg-Si alloy. The kinetics of precipitation during various stages of aging was modelled. The precipitate features consisted of particle radius and volume fraction obtained from the kinetics model, which was used to compute the alloy yield strength/hardness. A published multiinternal variable workhardening model was improved to take into account the effects of solute solution and precipitates on the alloy hardening capacity after performing different cycles of aging treatment. The flow curves and hardness predicted by the model were in good agreement with the experimental results. The model is able to... 

In this paper the previous velocity field proposed by the authors for the prediction of strain field and deformation load of circular cross section billet in ECAE process has been extended to take into account the deformation behavior of bimetal circular billet in the same process. Accordingly, using Bezier method, as a robust method for determining the geometry of the streamlines, the strain field developed in the circular bimetal billet is calculated. Then, based on the kinematically admissible velocity and strain fields and using the upper bound theorem the ECAE load is predicted. It was found that at constant inner corner angle of ECAE die, with decreasing of outer curve corner the... 

The 7075 aluminium alloy is one of the most important engineering alloys utilised extensively in aircraft and transportation industries due to its high specific strength. In the present research, the flow behaviour of this alloy has been investigated using hot compression test at strain rates of 0.001, 0.01, 0.1 and 1 s-1 and temperatures of 350, 400 and 450°C. The results reveal that dynamic softening occurred in these temperatures and strain rates. The activation energy, strain rate sensitivity and two constitutive equations (hyperbolic sine law and the power law) are derived from the results. It is shown that the hyperbolic sine law has a better agreement with the experimental results  

In this research in order to predict the strain distribution and extrusion load in equal channel angular extrusion (ECAE) process of circular cross section a new three dimensional kinematically admissible velocity field has been developed based on Bezier formulation. The strain distribution in deformation zone and the effects of various terms on extrusion load were determined. The results were compared both with the experimental and numerically predicted results reported in the literature. It was found that extrusion pressure decreases with increasing both the die angle and the outer curved corner angle and increases with increasing the friction coefficient. Also, it was exhibited that... 

In this study both the quench aging and static strain aging kinetics of a 6082 Al alloy were investigated at a temperature range of 130-200°C using the Vickers hardness and tensile test. The activation energy and dislocation density were determined at different stages of the aging phenomenon. The former was used to analyse the kinetics of aging and the latter to interpret the competition of strengthening and recovery mechanisms during aging. It is shown that different activation energies are achieved depending on the aging time and temperature relating to formation of appropriate precipitates at different stages of aging. Moreover, it is revealed that prestrain reduces the activation energy.... 

A mathematical model based on Kocks-Mecking-Bergstrom model, has been proposed to predict the flow behavior of age hardenable aluminum alloys, under different conditions of solution heat treatment and hot deformation. Considering the published literature, most researchers have taken into account the precipitation and solution strengthening contribution to the flow stress by a constant and some others have ignored these effects. So these available descriptions cannot be applicable directly to different conditions of solution heat treatment. In order to enable these constitutive descriptions to take into account the effects of soaking time and temperature, we introduce in this research a... 

The effect of tungsten and nitrogen on the as cast and the creep aged microstructures of heat resistant HP-Nb steel was studied. The steel was directionally solidified under two cooling rates of 31.2 and 7.6 K sec-1. Creep rupture tests were performed at temperatures of 1150-1255 K on the specimens prepared from the cast ingots in transverse and longitudinal directions. It is shown that the addition of nitrogen significantly increases the eutectic temperature and thus refines the dendrites and alters the morphology of M7C3 eutectic carbide. Also, it is found that due to short time aging, nitrogen addition decreases the M7C3 carbide fragmentation, increases the secondary M23C6 precipitation... 

The effects of sheet thickness and frictional condition between the punch and sheet on formability is predicted and compared with the experimental results of the Erichsen test as a stretch-forming process. The material and geometrical nonlinearity are considered. A hypoelastic-plastic model is used and strain-field stabilization is taken into account using the Assumed Strain Finite-Element Method. By considering the contact problem and applying the nonlinear finite-element method, the force and dome height for aluminum and steel sheets are computed and compared with the experimental results. The Oyane criterion is used to access the formability of the sheet. A good agreement was found... 

In this research, the plastic flow behavior of Al-6%Mg alloy was studied by analyzing the results of hot compression tests in a range of temperature and strain rate. Then, an artificial neural network (ANN) model was trained at which the temperature, strain-rate, and strain parameters were used as the input layer and the flow stress as the output. The comparison of the predicted and experimental results of stress-strain curve proved the prediction capability of the ANN model. © 2008 Elsevier Ltd. All rights reserved  

PM10 prediction has attracted special legislative and scientific attention due to its harmful effects on human health. Statistical techniques have the potential for high-accuracy PM10 prediction and accordingly, previous studies on statistical methods for temporal, spatial and spatio-temporal prediction of PM10 are reviewed and discussed in this paper. A review of previous studies demonstrates that Support Vector Machines, Artificial Neural Networks and hybrid techniques show promise for suitable temporal PM10 prediction. A review of the spatial predictions of PM10 shows that the LUR (Land Use Regression) approach has been successfully utilized for spatial prediction of PM10 in urban areas.... 

In this study, the importance of air temperature from different aspects (e. g., human and plant health, ecological and environmental processes, urban planning, and modelling) is presented in detail, and the major factors affecting air temperature in urban areas are introduced. Given the importance of air temperature, and the necessity of developing high-resolution spatio-temporal air-temperature maps, this paper categorizes the existing approaches for air temperature estimation into three categories (interpolation, regression, and simulation approaches) and reviews them. This paper focuses on high-resolution air temperature mapping in urban areas, which is difficult due to strong... 

The authors regret to inform that the values of parameters α1 and α2, in Tables 2 and 3 have replaced with each other incorrectly. The correct values are as follows: Table 2: [Formula presented] Table 3: [Formula presented] [Formula presented] Author would like to apologize for the inconvenience caused. © 2019 Elsevier Ltd  

Numerous cases of casing failure have been reported worldwide. Depletion-induced compaction is one of the main factors that may cause casing failure. Stress perturbation in salt layers may accommodate rock flow which endangers the stability of cased wells. Besides, poor cementing jobs are recognized as one of the wellbore instability causes. These factors need to be considered to determine the mechanism behind the casing failure. In this study, the creep behavior of the caprock salt layer in the southwest Iranian oil fields is experimentally studied through a number of creep tests under conditions of elevated temperature and pressure. Then, a three-dimensional finite element analysis is...