Sharif Digital Repository

TNT: Silicon microcantilevers modified with a three-dimensional layer of vertical titanium dioxide nanotubes can be used in micromechanical sensors with optical signal detection to detect low levels of explosives such as 2,4,6-trinitrotoluene (TNT) in the gas phase, even in the presence of other volatile impurities such as n-heptane and ethanol  

Al6063 powder was subjected to severe plastic deformation via high-energy mechanical milling to prepare ultrafine-grained (UFG) aluminium alloy. Uniaxial compression test at various temperatures between 300 and 450 °C and strain rates between 0.01 and 1 s-1 was carried out to evaluate hot workability of the material. Microstructural studies were performed by EBSD and TEM. The average activation energy and strain rate sensitivity of the hot deformation process were determined to be 280 kJ mol-1 and 0.05, respectively. The deformation temperature and applied strain rate significantly affected the grain structure of UFG Al alloy. A finer grain structure was obtained at lower temperatures and... 

An architectural modification method was utilized to improve fracture toughness of discontinuously reinforced aluminum (DRA) composites. Al-DRA composites having a structure similar to that of reinforced concrete were fabricated. The number of reinforcing DRA rods within Al matrix and volume fraction of SiC particles in DRA were altered to evaluate their effect on fracture behavior of these materials. It was found that architectural modification does not have any destructive influence on elastic modulus and yield strength of the composite. Moreover, the success of this method on toughness improvement strongly depends on the occurrence of debonding between Al and DRA regions upon loading  

The fabrication of strong photocatalysts applied to the degradation of organic pollutants is necessary in environmental applications. In a single-stage method, acetate precursor and poly vinyl pyrolydine are used to produce ZnO nanostructures with various morphologies in annealing temperatures ranging from 300 °C to 900 oC. The physical properties of the prepared nanostructures were characterized by SEM, XRD and PL spectroscopy. The SEM images exhibit a variety of the as-prepared hexagonal zinc oxides including wires, rods, particles and porous network of welded particles of ZnO nanoparticles. The results of the photocatalytic degradation of methylene blue as an organic dye in aqueous... 

TiO2 nanostructures with different morphologies (spherical, tube, leaf-like and flower-like particles) were synthesized via a facile hydrothermal process. Polycaprolactone (PCL)/10 vol.% TiO2 nanocomposites were prepared by solvent casting methods. In vitro bioactivity of the nanocomposite films was examined by immersion in the simulated body fluid (SBF) for up to 28 days. It was found that the morphology of titania nanostructures significantly influence the in vitro bioactivity of PCL/TiO 2 nanocomposites. This observation was attributed to the amount of anatase phase and the specific surface area of the TiO2 nanostructures, which provide high surface exposure to SBF  

In this work, novel chitosan/bacterial cellulose (CS/BC) nanofibrous composites reinforced with graphene oxide (GO) nanosheets are introduced. As cell attachment and permeability of nanofibrous membranes highly depend on their fiber diameter, the working window for successful electrospinning to attain sound nanofibrous composites with a minimum fiber diameter was determined by using the response surface methodology. It is shown that the addition of GO nanosheets to CS/BC significantly reduces the average size of the polymeric fibers. Their mechanical properties are also influenced and can be tailored by the concentration of GO. Fourier transform infrared spectroscopy reveals hydrogen bonding... 

A green and simple synthesis method based on a two-step chemical vapor deposition approach has been developed to synthesize transition metal dichalcogenides flakes. With non-toxic precursor such as transition metal oxides and elemental sulfur, large-area, strong photoluminescent and uniform MoS2 nanoflakes were produced at a relatively low growth temperature (650 °C). Controlling the layer number and morphology was achieved only by precursor concentration without any oxide impurity revealed by SEM, PL and Raman spectroscopy. This method can be used to make wide range of metal chalcogenides such as ZnS, SnS2, PtS2 and PdS2  

Al-20Si-5Fe melt was rapidly solidified into particles and ribbons and then consolidated to near full density by hot pressing at 400°C/250 MPa/1 h. According to the eutectic-growth and dendritic-growth velocity models, the solidification front velocity and the amount of undercooling were estimated for the particles with different sizes. Values of 0.43-1.2 cm/s and 15-28 K were obtained. The secondary dendrite arm spacing revealed a cooling rate of 6 × 105 K/s for the particles with an average size of 20 μm. Solidification models for the ribbons yielded a cooling rate of 5 × 107 K/s. As a result of the higher cooling rate, the melt-spun ribbons exhibited considerable microstructural... 

The aim of this work is to study the effect of cooling rate and subsequent hot consolidation on the microstructural features and mechanical strength of Al-20Si-5Fe-2X (X = Cu, Ni and Cr) alloys. Powder and ribbons were produced by gas atomization and melt spinning processes at two different cooling rates of 1 × 105 K/s and 5 × 107 K/s. The microstructure of the products was examined using optical microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The particles were consolidated by hot pressing at 400 °C/250 MPa/1 h under a high purity argon atmosphere and the microstructure, hardness and compressive strength of the compacts were evaluated.... 

In this study, novel hydrogel nanoparticles with dual triggerable release properties based on fibrous structural proteins (keratin) and thermoresponsive copolymers (Pluronic) are introduced. Nanoparticles were used for curcumin delivery as effective and safe anticancer agents, the hydrophobicity of which has limited their clinical applications. A drug was loaded into hydrogel nanoparticles by a single-step nanoprecipitation method. The drug-loaded nanoparticles had an average diameter of 165 and 66 nm at 25 and 37 °C, respectively. It was shown that the drug loading efficiency could be enhanced through crosslinking of the disulfide bonds in keratin. Crosslinking provided a targeted release... 

To enhance physicomechanical properties and bioactivity of fibrous membranes for wound dressing and tissue engineering applications, novel composite scaffolds consisting of fibrous mats and thermosensitive hydrogel particles were prepared by concurrent electrospinning and electrospraying technique. The composite scaffolds were composed of keratin/bacterial cellulose fibers (150 ± 43 nm) which are hybridized with hydrogel particles (500 nm to 2 μm) based on nonionic triblock copolymers conjugated with Tragacanth gum (TG). FTIR and H-NMR studies indicated ester reactions between carboxylated copolymers and TG through carbodiimide crosslinker chemistry. The hydrogel particles were uniformly... 

In this research, the ZnOG hybrid thin film was produced via solgel method. The surface morphology, band gap and photoactive properties of the films were studied by means of SEM, UV–Vis and photoluminescence analysis. In addition, the ability of the thin film in photocathodic protection of carbon steel (CS) and 304 stainless steel in 3.5 wt.% NaCl and Na2S solutions under dark and UV illumination was investigated by polarization test as well as OCP and current measurements during coupling of steels with ZnOG photoanode. The mix band gap is reduced to the orders of 1.17 eV through hybridization of ZnO with graphene oxide. In both NaCl and Na2S solutions, the ZnOG thin film could effectively... 

Manufacturing of complex-shaped bimetals utilizing two-color powder injection molding (2C-PIM) and three-dimensional printing (3DP) processes, which basically involve sintering of a powder/binder mixture, has been attracted a great interest. This article addresses sintering of biocompatible Co-Cr-Mo alloy for manufacturing stepwise porosity-graded composite structures. Such composite structures provide strength at the core and a porous layer for the tissue growth. To evaluate the process, two grades of gas atomized Co-Cr-Mo powder with an average particle size of 19 and 63 μm were used. Isothermal and non-isothermal sintering behavior of the loose powders under hydrogen and argon... 

The densification response of aluminum powder reinforced with 5 vol.% nanometric alumina particles (35 nm) during uniaxial compaction in a rigid die was studied. The composite powder was prepared by blending and mechanical milling procedures. To determine the effect of the reinforcement nanoparticles on the compressibility of aluminum powder, monolithic Al powder, i.e. without the addition of alumina, was also examined. It was shown that at the early stage of compaction when the rearrangement of particles is the dominant mechanism of the densification, disintegration of the nanoparticle clusters and agglomerates under the applied load contributes in the densification of the composite powder... 

Direct Metal Laser Sintering has real potential for rapid-manufacture applications in the PM arena, reducing lead times and cutting costs. But it has been hampered by the limited range of suitable powders available and their cost. A research group led by Fraunhofer scientists made their own powders and took a closer look.... © 2006 Elsevier Ltd. All rights reserved  

Recently, decellularized amniotic membrane-derived hydrogels (DAMHs) have received significant attention for wound care, ocular surface reconstruction, and chondral healing. Despite the advantages of DAMHs for tissue engineering (TE), the loss of structural components during the decellularization process mitigates their mechanical strength and thus limits their practical application. Herein, we present a method for the surface modification of two-dimensional nanosilicates (laponite) as a rheological modifier to tailor the properties of DAMHs. Results show that after introducing nanosilicates, severe aggregation of the nanoparticles occurs, owing to the shielding effect of ions on the surface... 

Recent advances in material issues for Direct Metal Laser Sintering (DMLS) process are presented. The concept is to decrease the powder particle size with the aim of enhancing the sintering kinetics and improving the surface quality of the produced parts. The outcome is particularly suitable for overcoming existing limitations with the rapid tooling, e.g. manufacturing of mould inserts for injection moulding and die casting, by the DMLS process. The powder composition was adapted near to the conventional P/M steels in order to get identical properties with a favourable price. Such novel powder material provides an opportunity to considerably reduce the product development time for P/M... 

We present a procedure for simultaneous deposition of enzyme-laden chitosan/reduced graphene oxide (rGO) film by electrophoretic deposition (EPD) for fast and efficient detection of glucose. The role of rGO nanosheets is studied on the EPD kinetics of the enzyme-laden suspensions. Investigating the performance of the biosensor by electrochemical techniques indicates its high sensitivity (9700 μA.mM−1.cm−2), low limit of detection (4 µM), and suitable selectivity. © 2021 Elsevier B.V  

Recently, nanodiamonds have attracted interest in biomedical applications such as drug delivery, targeted cancer therapies, fabrication of tissue scaffolds, and biosensors. We incorporated diamond nanoparticles in alginate-bioactive glass films by electrophoretic process to prepare functional coatings for biomedical implants. Turbidity examination by time-resolved laser transmittance measurement revealed that a stable multi-component aqueous suspension of alginate, bioactive glass and diamond particles could be obtained at concentrations of 0.6, 1.3, and 0.65 g/l, respectively. Uniform films with ~ 5 μm thickness were deposited on 316 stainless steel foils by employing constant field... 

Lead sulfide quantum dots (PbS QDs) were decorated onto a graphene surface in a semi-core-shell structure using supercritical ethanol. The temperature of ethanol played significant role in controlling size and agglomeration of QDs as well as the extent of reduction of graphene. Average size of the QDs was estimated by transmission electron microscopy to be around 3.96 nm and by quantum models to be about 4.34 nm. PbS QDs prepared at 330 °C were of high purity, and the yield was 99%. Instrumental and chemical analyses demonstrated formation of a strong bond between PbS QDs and graphene, through a Pb-O-C bridge. UV and photoluminescence measurements along with theoretical considerations...