Sharif Digital Repository

The gas nanosensor of indium oxide nanowires in laser assisted approach, doped with tin and zinc for gas sensing and 1D growth purposes respectively, was reported. The nanowires were very sensitive to H2S gas in low concentration of 20 ppb gas at room temperature. The fast dynamic intensive and sensitive response to gas was in a few seconds with an on/off sensitivity ratio of around 10. The square cross-section indium oxide nanowires were fabricated through physical vapor deposition (PVD) mechanism and annealing approach. The field emission scanning electron microscopy (FESEM) observations indicated that the annealing temperature was vital in nanostructures' morphology. The fabricated... 

In this paper, the stable and reproducible tellurium doped ZnO nanowires (Te-ZnO NWs) photodetector with intensive responsively is presented. The Te-ZnO NWs were fabricated by physical vapor deposition (PVD) growth mechanism. Field emission scanning electron microscope (FESEM) images showed that the fabricated nanowires were 50 nm in diameter and several microns in length. The high resolution transmission electron microscopy indicated that the synthesized nanowires were crystalline and their phase characterization was validated by the X-ray diffraction (XRD). The photoluminescence (PL) studies of these nanowires showed a strong photoluminescence (PL) emission peak in the green region. It was... 

In this article, indium doped ZnO nanoparticles (alloy nanoparticles) were investigated as inhibitors against algae growth on adobe mud and earthen artworks for surface preservation from destruction caused by micro-organisms under humid conditions, through surface modification and activation run off. Nanoparticles (NPs) were fabricated by physical vapor deposition (PVD) growth mechanism. The fabricated NPs were approximately 20 nm in size. The Chlorella vulgaris and Scenedesmus quadricauda were tested by application of indium doped ZnO nanoparticles (In/ZnO NPs) as inhibitors. As concentrations of NPs increased, the negative impacts of NPs on the algal growth were enhanced and physical... 

A long-term antibacterial activity of implants without compromising their biocompatibility is highly desirable to minimize the biomaterial-associated infections. Although tantalum oxide nanotubes (Ta2O5 NTs) are promising coating materials for orthodontics and orthopedics applications, their insufficient antibacterial activity retains vulnerability to post-implantation infections. This study aimed to endow antibacterial characteristics to the Ta2O5 NTs-coated Ti6Al4V substrates by decoration of silver oxide nanoparticles (Ag2O NPs). The well-adherent Ta2O5 NTs were grown via anodization of a pure tantalum (Ta) layer coated by physical vapor deposition (PVD) on the Ti6Al4V substrates. The... 

The nanotubular arrays of titanium dioxide (TiO2 NTs) have recently received considerable interest for fabrication of dental and orthopedic implants. However, their antibacterial activity requires substantial improvement for the potential infections minimization, without compromise of their biocompatibility. In this work, TiO2 NTs were developed on Ti6Al4V substrates via anodization at a constant potential of 60 V for 60 min, followed by heat treatment at 500 °C for 90 min. Physical vapor deposition (PVD) was further employed to decorate silver oxide nanoparticles (Ag2O NPs) on the nanotubular edges. The results indicated that the highly-ordered TiO2 NTs with decorated Ag2O NPs could promote... 

The highly sensitive impedimetric biosensor in label free approach for hepatitis B virus DNA (HPV DNA) detection based on tellurium doped ZnO nanowires was fabricated. The NWs were grown by hybrid thin film oxidation in the physical vapor deposition (PVD) mechanism. The morphology characterization of the synthesized NWs was performed by field emission scanning electron microscopy (FESEM) and the images demonstrated that the diameter and the length of the materialized NWs were around 50 nm and several micrometers, respectively. The high-resolution transmission electron microscopy (HRTEM) image indicated that the fabricated NWs were crystalline and their phase characterization was validated by... 

WO3 films with thicknesses between 550 and 853 nm were deposited on glass substrates using the electron beam evaporation method at room temperature. The microstructures and surface roughness of the films were studied by X-ray diffraction (XRD) and atomic force microscopy (AFM). It was observed that the crystalline structure of the WO3 thin films significantly changes from the amorphous to crystalline states with a crystalline texture, and the mosaicity and grain size dependent on the film thickness. The transmittance spectra of the obtained WO3 films were measured in the range from 340 to 850 nm, and the Swanepoel method was used to determine the refractive indices and the thicknesses of the... 

Hematite (α-Fe2O3) is a promising candidate for water oxidation applications due to its abundance in the earth crust and its suitable bandgap. However, hematite performance is severely limited by electron-hole recombination at its interface with the electrolyte; something that can be addressed using electrocatalysts. In this report, we evaluate the influence of a ternary NiFeCo co-catalyst to enhance the water oxidation performance of hematite photoanodes. Thus, NiFeCo co-catalyst is optimized for hematite thin films with i) dense and ii) porous (nano-rod) morphologies. Both hematite films are prepared using electron beam evaporation method followed by an annealing step and NiFeCo... 

In this study, ZrO2 coatings with different thicknesses were grown by the electron beam evaporation technique. The crystalline structure was studied by XRD analysis which suggested the tetragonal and monoclinic phases for ZrO2 coatings. Additionally, the film thickness slightly enhanced the crystallinity. The surface morphology and fractal features were analyzed using Scanning Electron Microscopy (SEM). The surface statistical parameters and the fractal geometry were employed to analyze the impact of the coating thickness and homogeneity on the morphology of the films. The statistical processing and fractal dimension revealed variations in the morphology parameters due to the electron beam... 

WO3 films with thicknesses between 550 and 853 nm were deposited on glass substrates using the electron beam evaporation method at room temperature. The microstructures and surface roughness of the films were studied by X-ray diffraction (XRD) and atomic force microscopy (AFM). It was observed that the crystalline structure of the WO3 thin films significantly changes from the amorphous to crystalline states with a crystalline texture, and the mosaicity and grain size dependent on the film thickness. The transmittance spectra of the obtained WO3 films were measured in the range from 340 to 850 nm, and the Swanepoel method was used to determine the refractive indices and the thicknesses of the... 

Studies on copper zinc tin sulpher selenide (CZTSSe) thin-film material and its applications as a base material are intensively being researched since it is an earth-abundant, inexpensive, flexible, and interesting material for next-generation optoelectronic technologies. Apropos, this study explores and reports the synthesis of CZTSSe thin films and their key optoelectronics characteristics. The reported films are fabricated on a soda-lime glass substrate by using a physical vapor deposition technique, and then annealed from 250 to 450 °C. From the X-ray diffraction analysis, the structure of the as-deposited thin films is found to be amorphous in nature. Annealed thin films of CZTSSe... 

Studies on copper zinc tin sulpher selenide (CZTSSe) thin-film material and its applications as a base material are intensively being researched since it is an earth-abundant, inexpensive, flexible, and interesting material for next-generation optoelectronic technologies. Apropos, this study explores and reports the synthesis of CZTSSe thin films and their key optoelectronics characteristics. The reported films are fabricated on a soda-lime glass substrate by using a physical vapor deposition technique, and then annealed from 250 to 450 °C. From the X-ray diffraction analysis, the structure of the as-deposited thin films is found to be amorphous in nature. Annealed thin films of CZTSSe...