Sharif Digital Repository

The present study investigates the dynamic filtration of concentrated slurry fluids containing colloidal clay particles under different salinity, shear flow, and flux rate conditions. The dynamic filtration study was carried out by the filtration cell equipped with a rotating disk to apply shear stress over the membrane surface. A 3D CFD simulation has been implemented to model the hydrodynamic flows inside the filtration cell to obtain the wall shear stress (WSS) on the membrane surface at different disk rotation speeds. The thickness and surface patterns of fouling were captured utilizing a surface profilometer. First, the cake-filtration model was used to predict the flux rate and fouling... 

During oil and gas well drilling, the filtration control of bentonite water-based drilling fluids (BT-WBDFs), as an environmentally friendly fluid, is crucial to avoid formation damage and swelling shale problems. One of the most critical problems is undesirable changes in the rheology and filtration properties of the BT-WBDFs because of salt contamination. Herein, the potential of using both graphene oxide (GO) nanosheets and a graphene oxide-polyacrylamide (GO-PAM) nanocomposite is evaluated for controlling the filtration properties, especially in a salty medium. First, GO nanosheets were functionalized, and then the GO-PAM nanocomposite was synthesized using the solution polymerization... 

A better performance and consequently the widespread use of polymeric insulators in different parts of the power grid can increase their role in the grid reliability. The accumulation of contamination and housing-erosion are the two most effective factors in undermining the performance of this type of insulators. Therefore, electric utilities need to identify contaminated insulators for washing and cracks in polymeric housing to replace them with healthy specimens. This paper discusses the impact of contamination layer and housing-erosion of polymeric insulators on the partial discharges (PD) at the insulator surface, through RF-PRPD (phase resolved partial discharge) patterns. The existence... 

Mechanical failure of materials adjacent to the production cavity and material disaggregation caused by fluid drag are considered as the most important parameters that affect sand production. In light of such factors, the coupling of two mechanisms-mechanical instability and hydrodynamic erosion-is indispensable in order to model this phenomenon successfully. This paper examines the applicability of a coupled hydro-mechanical erosion criterion for simulating sand production using the finite element method. The porous medium was considered fully saturated. The onset of sanding and production of sand were predicted by coupling mechanical failure and subsequent erosion of the grain particles... 

Observatory-scale data collection efforts allow unprecedented opportunities for integrative, multidisciplinary investigations in large, complex watersheds, which can affect management decisions and policy. Through the National Science Foundation-funded REACH (REsilience under Accelerated CHange) project, in collaboration with the Intensively Managed Landscapes-Critical Zone Observatory, we have collected a series of multidisciplinary data sets throughout the Minnesota River Basin in south-central Minnesota, USA, a 43,400-km2 tributary to the Upper Mississippi River. Postglacial incision within the Minnesota River valley created an erosional landscape highly responsive to hydrologic change,... 

Erosive wear is one of the efficiency reduction causes in centrifugal compressors. The presence of suspended solid particles in the fluid causes deformations in different parts of the compressor, especially blades of the impeller. Therefore, erosion not only decreases the part lifetime by destruction of blades form, but also increases energy losses. For this reason, specifying the erosion locations and choosing a suitable material have an important effect on optimum functionality of the machine. In this paper, erosion locations of a compressor impeller by using computational fluid dynamics (CFD) in high temperature and pressure are attained and compared with experimental model. The... 

In the present paper, the effect of Nano silica on mechanical properties and durability of concrete containing polypropylene fibers has been investigated. Here, the length and length to diameter ratio of used polypropylene fibers were considered to be fixed and equal to 18 mm and 600 respectively and the cement content was 479 kg/m3. The effect of fibers and Nano silica in four different percentages for each one at 0.1, 0.2, 0.3 and 0.4 percent by volume for fibers and 3 percent for Nano silica in concrete with water to cement ratio of 0.33, 0.36, 0.4, 0.44 and 0.5 have been compared and evaluated. In total, more than 425 cubic and cylindrical specimens were made according to ASTM standards.... 

The grain-size distribution (GSD) of porous rocks is important in order to better understand their hydrodynamic behavior. Clear and precise GSD data can be used to computationally reconstruct rock structure for further analysis. In this study, three main algorithms for image analysis have been examined to estimate the GSD of clastic rocks. The main challenge in GSD determination from images is in detecting overlapping grains and measuring their size separately. In this study, three previously developed image processing algorithms are implemented on two-dimensional (2D) binary images of rocks in order to compare the obtained GSD from each of the methods, i.e., the mean intercept length... 

This study investigates critical run-off and sediment production sources in a forested Kasilian watershed located in northern Iran. The Water Erosion Prediction Project (WEPP) watershed model was set up to simulate the run-off and sediment yields. WEPP was calibrated and validated against measured rainfall-run-off-sediment data. Results showed that simulated run-off and sediment yields of the watershed were in agreement with the measured data for the calibration and validation periods. While low and medium values of run-off and sediment yields were adequately simulated by the WEPP model, high run-off and sediment yield values were underestimated. Performance of the model was evaluated as... 

Whole level of the erosion and the resistance of rocks which were composed closured have been studied, besides, the impact of temperature and laser irradiation for more investigation about this issue has been involved before all. This subject more reveals the matter which laser absorption on the laboratory scale using laser to what extent can cause the augment of the relative permeability and secondary porosity of reservoir rock, that of the vertical and horizontal useful connectivity and eventually that of the positive transferability. This research has been carried out in the form of case study on one of Iranian south west formations in north east of Behbahan city in Iran, either the rate... 

Accurate estimation of scour depth is needed for economic and safe determination of bridge pier foundation depth. Most design criteria are based on maximum scour depth due to the steady design discharge without flow time limit. In this paper, the results are presented of an experimental investigation on local scouring around a single bridge pier under steady and unsteady flow regimes. For unsteady flow, triangular shape hydrographs with repeatable peaks have been chosen. Results show that both sharp and flat increases to the peak of hydrographs have a negligible effect on scour depth for the same base time. An equation is obtained to compute the scour depth due to a specific triangular... 

The low erosion resistance of titanium and its alloys has prevented their widespread application as joint implants. In addition, one essential requirement for the implants to bond with the living bone is the formation of a bone-like apatite on their surfaces in the host body. To enhance the erosion resistance of the surface, a diffused layer of TiB2 was formed at 1000uC on the commercial pure titanium. Hydroxyapatite was then coated on the boronised titanium by means of dip coating in a sol-gel solution. In order to confirm the biocompatibility of the specimens, they were soaked in a simulated body fluid for several days. The surface morphology of the specimens after exposure was studied by... 

According to available information and references, water leakage and internal erosion in bodies and foundations of embankment dams are the main reasons of many problems and failures. To reduce this risk in foundation, plastic cut off walls is one of the most reliable solutions. In this research the effect of specimen's age on the mechanical properties of plastic concrete was studied. This paper summarizes the test results which were conducted in unconfined and triaxial state. Plastic concrete specimens were prepared in the laboratory condition using the materials provided from the Silve dam site. Test results have shown that the time and confining pressure extremely affect the mechanical... 

In this study amount of soil erosion in watershed of JAJROOD is estimated by use of the RULSE model with the help of GIS12. JAJROOD River is located in upstream of LATIAN Dam and is one of the most important water sources of Tehran. Also, this River has a big role in preventing the flood. modeling Results show that the amount of soil erosion is high due to high slope of the land, lack of plant coverage and the quality of soil and changing the land application, lead to increase in erosion potential. modeling Results have estimated the amount of erosion in this basin about 1,524,511 tons in a year. In order to evaluate Results and efficiency of the model, all of obtained results are compared... 

High bed-shear stress resulting from secondary flows and velocity increase at a channel junction cause local erosion and deposition in natural rivers and earth-lined channels. Herein, the scour patterns at the junction of two loose bed channels were studied under clear-water conditions. The main dimensionless variables are the angle between the two approach flow branches, the discharge and width ratios of the tributary to the downstream channel branches, and the ratio of the mean downstream velocity to the threshold velocity. The results indicate that the position of the maximum scour depth temporally moves to the outer wall and upstream to the main channel, as affected by the dimensionless... 

The process of local scour around bridge piers is fundamentally complex due to the three-dimensional flow patterns interacting with bed materials. For geotechnical and economical reasons, multiple pile bridge piers have become more and more popular in bridge design. Although many studies have been carried out to develop relationships for the maximum scour depth at pile groups under clear-water scour condition, existing methods do not always produce reasonable results for scour predictions. It is partly due to the complexity of the phenomenon involved and partly because of limitations of the traditional analytical tool of statistical regression. This paper addresses the latter part and... 

In this paper, the structure of a wall jet deflected by a baffle along with the trajectory of particles has been studied. This baffle is used to produce a stable deflected surface jet, thereby deflecting the high-velocity supercritical stream away from the bed to the surface. An elliptic relaxation turbulence model (v2̄ - f model) has been used to simulate this submerged flow. During the last few years, the v2̄ - f turbulence model has become increasingly popular due to its ability to account for near-wall damping without use of damping functions. In addition, it has been proven that the v2̄ - f model is superior to other RANS methods in many fluid flows where complex flow features are... 

Ni-base superalloy René 80 is widely used in manufacturing aircraft turbine blades. The service temperature of this alloy is in the range of 760-982 °C. Although this alloy possesses suitable mechanical, oxidation and hot corrosion properties, it is coated in order to increase its wear, oxidation, erosion and hot corrosion properties against harmful environmental service conditions. In this paper the influence of applying diffusion coating (CODEP-B) on the tensile properties of René 80 has been studied in the temperature range of 22-982 °C. Experimental results show that the tensile properties of the coated specimens are relatively lower than that of uncoated ones in the same conditions. But... 

In this study, effects of tungsten on wear resistance of high chromium white cast iron with and without tungsten in erosion-corrosion condition have been investigated. At the same time, the comparison between wear resistance of this grade of cast iron and low alloy steels with various contents of Cr which are used in industrial condition (in Sarcheshme Company, the greatest copper production company in the Middle East and with more than 4000 years historical cupper production background) was studied, while, copper concentrates have used for erosion particles. Results show that, because of higher hardness of matrix due to the tungsten, the wear resistance of high chromium cast iron increases.... 

This paper introduces the concept of a submerged hydraulic jump being used for energy dissipation. A baffle wall is used to produce a stable deflected surface jet, thereby deflecting the high-velocity supercritical stream away from the bed to the surface. An elliptic relaxation turbulence model (v 2̄ - f model) has been used to simulate this submerged flow. During the last few years, the v2̄ - f turbulence model has become increasingly popular due to its ability to account for near-wall damping without use of damping functions. In addition, it has been proved that the v̄2 - f model is superior to other RANS methods in many fluid flows where complex flow features are present. In this study,...