Sharif Digital Repository

The hybrid rocket motor is a kind of chemical propulsion system that has been recently given serious attention by various industries and research centers. The relative simplicity, safety and low cost of this motor, in comparison with other chemical propulsion motors, are the most important reasons for such interest. Moreover, throttle-ability and thrust variability on demand are additional advantages of this type of motor. In this paper, the result of an internal ballistic simulation of hybrid rocket motor in a zero-dimensional form is presented. Further to validate the code, an experimental setup was designed and manufactured. The simulation results are compared with the experimental data... 

Extensive low speed wind tunnel experiments have been undertaken to measure the test section, oor wall pressure distribution, in the presence of a 2D wing inside the test section. The experiments were performed for both the static and dynamic pitching motion of the model under difierent conditions. In these measurements, the efiects of the existence and oscillations of a 2D wing on the oor wall pressure at various locations were studied. According to the results, as the oscillation parameters, such as mean angle of attack and frequency, change, wall pressures at the points located in the front part of the test section, in the upstream region, exhibit difierent behavior from those in the... 

An existing operational trisonic wind tunnel is upgraded to improve its performance criterion in the transonic regime. In this research, the test section is modified according to the operational requirements of the various existing transonic wind tunnels. Several perforated walls are designed, manufactured, and installed on the top and bottom sides of the test section. The flow in the test section of the wind tunnel is surveyed for the empty condition prior to testing models. Once satisfactory results regarding the flow quality requirements in the test section under various conditions were achieved, a 2D model, NACA 0012, and a 3D standard model for the transonic wind tunnels, AGARD-B, are... 

A series of experiments were conducted to study the effect of leading-edge roughness on the state of the boundary layer of a wind turbine blade section using multiple hot-film sensors. The experiments involved static and dynamic tests, where airfoil motion was of plunging type oscillation. The application of surface grit roughness simulates surface irregularities that occur on the wind turbine blades. The measurements showed that increasing the angle of attack results in movement of transition locations toward the leading edge. Surface roughness moved the transition point toward the leading edge and caused early trailing edge turbulent separation, which resulted in reducing the effectiveness... 

Extensive subsonic wind tunnel tests were conducted on a coplanar wing-canard configuration at various angles of attack. In these experiments, a 60° swept canard was placed upstream of a 60° swept main delta wing. This paper deals with the distribution of mean and fluctuating pressure coefficients on the upper surfaces of both the canard and the wing immersed in a variety of angles of attack. According to the results, presence of canard postpones the vortex formation and growth on the wing to higher angles of attack compared to the canard-off case. Due to the canard downwash field, the wing operates at lower effective angles of attack and therefore, its vortex breakdown is delayed. The... 

This is an experimental study on the boundary layer over an airfoil under steady and unsteady conditions. It specifically deals with the effect of plunging oscillation on the laminar/turbulent characteristics of the boundary layer. The wind tunnel measurements involved surface-mounted hot-film sensors and boundary-layer rake. The experiments were conducted at Reynolds numbers of 0.42×10 6 to 0.84 × 10 6 and the reduced frequency was varied from 0.01 to 0.11. The results of the quasi-wall-shear stress as well as the boundary layer velocity profiles provided important information about the state of the boundary layer over the suction surface of the airfoil in both static and dynamic cases. For... 

A new genetic algorithm (GA) based method for direct calibration of 2-D hot-wire probe and other instruments that can measure 2-D flow properties is introduced. This new method is an alternative for the previous QR method that is commonly used for calibration of the X-probe hot wires. The proposed GA method resulted in a much smaller error in the velocity estimation while preserving the number of sentences in its calibration equation format. In addition, it preserves the magnitude of its error even when the number of sentences in the calibration equation is decreased while the error in the QR method increases substantially for the same situation. Furthermore, the results were much closer to... 

Extensive wind tunnel tests were performed on several wing- body-tail combinations in subsonic flow to study the effects of wing geometric parameters on the flow field over the tail. For each configuration, tail surface pressure distribution, as well as the velocity contour at a plane perpendicular to the flow direction behind the wing was measured. The results show a strong effect of wing to tail span ratio, as well as wing aspect ratio, on the flowfield downstream of the wing. For low sweep wings, as those considered here, wing and body interference effects on the tail are associated with the wing tip vortex and nose-body vortex  

Experiments are performed to evaluate the impact of trip wires on the turbulence intensity in a few low speed wind tunnels. Trip wires of different sizes are installed at different positions in the contraction section of four different wind tunnels and measurements are made at various free stream velocities. The results indicate that the pressure distributions are altered compared to the clean condition. Trip wires move the adverse pressure gradient toward the inlet of the contraction section. Consequently, the turbulence intensity in the test section of the wind tunnels is reduced and the flow uniformity is improved considerably. Frequency and statistical analysis are performed and the... 

In this study, we performed experiments to investigate the effect of sweep angle on the transition location of laminar flow to turbulent flow. Three half wing models were used, each having a different sweep angle but with the same aspect ratio in various angles of attack. Two flat plates were used at the ends of the swept wing models to prevent the flow from rolling up over the wing. By simulating flow over infinity swept wing by eliminating tip vertices, the effect of sweep angle on flow transition phenomenon was investigated. The experiments included the study of transition flow via hot-film sensors, which were glued on the wing surface. We found that the small leading-edge radius and low... 

Conventional buffet onset methods for a 2D supercritical airfoil, SC0410, in transonic regime for various Mach number and various angles of attack have been surveyed. The existing methods give good results for high subsonic and transonic regimes, but demand a computational procedure to detect the buffet onset. One of these methods, trailing edge pressure divergence, that have been recognized inappropriate in other studies for supercritical airfoils, shows acceptable result at least for the present supercritical airfoil. A new method has been proposed by the authors for transonic regime that is based on the physical definition of the buffet onset from the surface pressure distribution... 

Extensive low-speed wind-tunnel tests are performed to study the flow field structure over a dual-surface canard, known as split canard, in comparison to the conventional configurations. Surface pressure for both steady deflections and unsteady oscillations of the canard are measured and compared for both canard-alone and split-canard cases. The split canard shows a superior advantage at high angles of attack, where a delay in the vortex breakdown phenomena on the canard surface is observed. For the split-canard configuration, the downwash of the front canard reduces the effective angle of attack at the inboard section of the rear element which postpones formation of the leading-edge vortex.... 

In this study a multi-objective genetic algorithm is utilized to obtain a Pareto optimal set of solutions for geometrical characteristics of airfoil sections for 10-meter blades of a horizontal axis wind turbine. The performance of the airfoil sections during the process of energy conversion is evaluated deploying a 2D incompressible unsteady CFD solver and the second law analysis. Artificial neural networks are trained employing CFD obtained data sets to represent objective functions in an algorithm which implements exergetic performance and integrity characteristics as optimization objectives. The results show that utilizing the second law approach along with Pareto optimality concept... 

Extensive experimental investigation was conducted to study the effect of leading-edge roughness on the state of the boundary layer of a wind turbine blade section. The application of surface grit roughness simulates surface irregularities that occur on the wind turbine blades. The measurements were done using multiple hot-film sensors and surface pressure transducers in both static and plunging oscillation of the airfoil. Frequency domain analysis was used to determine the state of the unsteady boundary layer  

This investigation addresses the boundary layer study of a plunging airfoil. It specifically concerns the effect of reduced frequency on transition and separation/reattachment of the unsteady boundary layer. The wind tunnel measurements were conducted using multiple hot-film sensors, pressure transducers and a boundary-layer rake, at Reynolds numbers of 0.42 to 0.84 million, and over reduced frequencies from 0.05 to 0.11. It was observed the boundary layer transition occurs by a laminar separation bubble. The unsteady laminar separation is promoted (delayed) by the increase of the reduced frequency in upstroke (downstroke) portion of the equivalent angle of attack  

In this paper, the effects of turbulence on sound generation and velocity fluctuations due to pressure waves in a large subsonic wind tunnel are studied. A trip strip located at different positions in the contraction part or at one position in the diffuser of a large wind tunnel is used to investigate the aforementioned phenomenon, and the results indicate that the trip strip has significant effects on sound reduction. The lowest turbulence intensity and sound are obtained from a trip strip with a diameter of 0.91mm located either at X/L = 0.79 or at X/L = 0.115 in the wide portion of the contraction. Furthermore, the effect of monopole, dipole and quad- rupole sources of aerodynamic noise... 

Supersonic flow over a tapered body of revolution has been investigated both experimentally and numerically. The experimental study consisted of a series of wind tunnel tests on an ogive-cylinder body. Static pressure distributions on the body surfaces at several longitudinal cross sections, as well as the boundary layer profiles at various angles of attack have been measured. Further, the flow around the model was visualized using Schlieren technique. Tests with a natural development of the boundary layer and with tripping were also carried out. All tests were conducted in the trisonic wind tunnel of Qadr Research Center. Our results show that artificial boundary layer tripping has minor... 

A series of supersonic visualization tests were performed on an airplane model in both static and dynamic pitching cases. After image processing, the wave angles originating from different parts of the model were carefully measured and averaged over several oscillation cycles. These findings were then compared with the corresponding normal force under similar conditions. The results reveal a hysteresis loop in variations of the model shock angles with instantaneous angles of attack during upstroke and down-stroke motions. In comparison with the normal force hysteresis loop, it has been found that there is an interesting relationship between the shape of the hysteresis loop of the shock angle... 

A series of experiments was performed to investigate the interaction of an under-expanded axisymmetric supersonic jet exhausted from a flat plate with a high subsonic crossflow. The goal was to study the effect of boundary layer thickness (δ) and jet to freestream dynamic pressure ratio (J) on flow field pressure distributions. The resulting measurements upstream of the jet showed that with increasing boundary layer thickness, the magnitude of the pressure coefficient decreases, whereas downstream of the jet, the recovery of the back-pressure moved closer to the nozzle exit. Flow field measurements indicated that with increasing boundary layer thickness, the jet plume dissipation rate... 

The first notable megawatt class wind turbine, which was the pioneer of improvement in the blade performance in large wind turbines, appeared in Vermont. Nowadays, modern wind turbines are using blades with multi-airfoils at different sections. In this study, in order to indicate the best airfoil profile for the optimum performance in different sections of a blade, five popular airfoils, including S8xx, FFA and AH series, were studied. On the large-scale profile, shear stress transport K–ω model was applied for the simulation of horizontal axis wind turbines for different wind speeds. The aerodynamic simulation was accomplished using computational fluid dynamic method, which in turn is based...