Sharif Digital Repository

One of the most important manufacturing methods using technologies AM, is the SLS method. This method because it would significantly reduce the construction time is the ability to build a variety of materials, is pervasive. The SLS devices input is part CAD file which is then part layered, a layer of powder is poured on the bed. Each layer is defined contour on the part and then scanned by laser inner layer is hatched by laser. Scanning algorithms and hatching in the SLS is an important part of building that has an impact on properties part and a lot of research has been done about it. synthetic scan algorithms presented in this study. The purpose of this algorithm is that part warpage and... 

In this work, polyvinylidene difluoride (PVDF) as a ferroelectric polymer, polyaniline (PANI) and polypyrrole (PPy) as conductive polymer additives are used to fabricate high performance mesoporous CH3NH3PbI3-xClx mixed-halide perovskite solar cells in a sequential deposition method. Using polymer additives in perovskite precursor solution leads to modification of perovskite layer morphology by changing nucleation and growth of perovskite grains. Besides, conductive polymer additives in perovskite layer help to more charge carrier transfer. Power conversion efficiency has been enhanced from 10.40 % to 16.51% and to 13.21 % in ambient atmosphere in the presence of 1.0 wt. % of PVDF and PPy... 

Wax precipitation is one of the major problems in the transfer of crude oil from field production to refineries. This wax with asphaltene compounds and some water and solids, closes the oil pipeline. One of the ways to reduce the amount of wax in pipes is to use additives (flow improvers) to crude oil and improve its rheological behavior. In this research, Five Iranian crude oils were characterized with SARA test and then the effects of various additives including ethylene vinyl acetate (EVA) in concentrations of 500 and 1500 ppm, alkyl phenol ormaldehyde resins (NPFR) with 1500 ppm and styrene-(ethylene-cobutylene)- styrene (SEBS) with 1500 ppm on viscosity, wax appearance temperature... 

Wire arc additive manufacturing (WAAM) is used to manufacture parts in large scale, low cost, and at high rate of production. One of the problems of this technique is the creation of residual stress in the produced components. The aim of this study is to investigate the efficiency of procedures reducing the amount of residual stress to ameliorate the WAAM technique. In this research, the WAAM method and the procedures for reducing the amount of residual stress are explained. Also the advantage of this technique is presented. Due to the enormous amount of parameters and for the aim of saving time and expense, the simulation method is used. The accuracy of the simulation was checked with... 

Dithiocarbamates are a group of compounds that nowadays have been used extensively in pharmaceutical agents, organicsynthesis and as fungicides in agriculture.We haveshown, an efficient. regiospecific method for the synthesis of cyclic dithiocarbamates by one-pot three-component cascade reaction of an amine, CS2 and α,β-unsaturated aldehyde via Michael addition/hemiamination reaction in watre under a mild and green procedure with excellent yields and complete regioselectivity  

The main objective of all managers of the economic organizations, manufacturing and industrial companies and service providers is to take steps toward improvement and effective use of different resources like workforce, capital, materials, energy and information. To attain the desired productivity, managers have to observe requirements such as establishment of a working organizational structure, effective implementation methods, safe equipment and tools, balanced working atmosphere and qualified human force as the most important factor. Therefore productivity culture should be publicized throughout the organization, and human force should be considered as the main component of this process.... 

Recently, a new method to investigate chip seal performance has developed by a research team at Sharif University of Technology. This study investigates the effect of various additives such as CRM, SBR Latex, Hydrated Lime and Ordinary Portland Cement (OPC), on the curing time of chip seal by this method. In addition, the chip seal treatments were investigated in different climate conditions like Wet and Wet-Freeze zones. The overall performance of mixture specimens evaluated using creep loading test. In fact, the bonding properties between aggregates and surface of Hot Mix Asphalt measured. The test results were analyzed by using of the work and time parameters. These parameters were... 

Flexible cones are one of the latest bone loss treatment methods in the ever-increasing revision total knee arthroplasty. This study is conducted to assess the biomechanical performance of the tibial flexible cellular cones in enhancing the initial stability of the implant system through the analysis of implant micromotion, as well as minimizing stress shielding through the analysis of strain distribution in the bone. The research evaluates the impact of various geometrical variables, including the thickness of the porous wall, the presence, type, width, number, and location of the inner solid wall notches on the spring stiffness and stress distribution of these cones. The research... 

Joining metal and alloy is a continuous and inevitable effort in oil and gas and automotive industry, and a considerable number of these joints are dissimilar joints. Steels and aluminum alloys are two of the most utilized engineering material and bi-metallic steel-aluminum parts have a lot of applications due to having the combined properties of both alloys (for example the high tensile strength and wear resistance of steels along with good thermal and electrical conductivity and corrosion resistance of aluminum alloys). However, fusion welding of aluminum to steel possesses great challenges due to the difference in melting point, coefficient of thermal expansion, thermal conductivity and... 

With advancement of science of aircraft design and limitations of traditional manufacturing methods, using new ones in order to improve efficiency is needed. Among those methods to improve structure efficiency are weight reduction or increase in strength. Increasing strength-to-weight ratio and reduction of weight could be achieved by using composite materials and topology optimization respectively. Manufacturing such parts with efficient design using traditional methods is hard or impossible. Additive manufacturing as a new technology which is being developed every day, can be a big help to aerospace industry. Considering the importance of strength-to-weight ratio in aerospace industry and... 

Selective Laser Sintering (SLS) is one of the powder-based Additive Manufacturing (AM) technology in which parts built by CO2 laser. In this research work, Titanium-PMMA-Stearic Acid powders are mixed together to produce parts by Indirect Metal Laser Sintering (IMLS) method. The optimum process parameters such as energy density, Percentage composition of Titanium-PMMA and Scan Sintering are obtained by adopting the Taguchi method for getting the maximum density and minimum porosity. Experiments are planned by Taguchi’s Mix-L8 orthogonal array. According to the results obtained from this study, the percentage of combination Ti-PMMA and Energy density, respectively, are a major parameters that... 

Additive manufacturing technology (AM) is one of the new methods of rapid prototyping. Experts claim that using this process can produce a prototype of the product with any complex geometry in the shortest possible time. Among the methods of metal additive fabrication, the direct metal layering method with the powder coaxial nozzle has different capabilities and has received much attention by researchers. In this research, we intend to find a relationship between device parameters and the geometry of samples made by direct metal layer method. According to the research, many parameters affect the quality of the samples made by this method, the most effective of which are the three parameters... 

Formation acidizing is one of the best well stimulation methods to remove reservoir damage and improve recovery of oil and gas well. The proper design of acidizing operations can significantly improve the production of a formation. In the meantime, causing formation damage and precipitation in oil flowlines, which may be caused by the incompatibility of the stimulation fluid with the reservoir fluid and rocks, is one of the most serious problems in the operation, which reduces permeability and oil/gas production. As a result, the success of the acidizing operation requires to study the interaction of components of operation (acid, reservoir water, formation rock, and acid additive)... 

Crude oil is naturally not applicable to the refining processes to obtain important products. Most of the crude oil refining process produce heavy hydrocarbons that are not used much in the same way. More refineries are looking for a process to remove the heavy components and converts these materials into valuable material. There are different process for upgrading heavy residual oil. One of the main processes in residual upgrading is Delayed Coking. The high flexibility to the different feeds and no need for a catalyst, causing a shift in the approach to the refinery for processing heavy crude oil by Delayed Coking. The aim of this project is calculated the sulfur content and and yield of... 

Currently, one of the most important problems in the field of drilling is the issue of drilling fluid loss in different formations. The problem of mud loss has been evident since the beginning of oil and gas well drilling operations, so that oil companies spend millions of dollars annually to solve the problem of mud loss. Problems such as pipe jamming, loss of rig production time, well blowout, loss of a large volume of drilling mud and damage to reservoir formations due to loss of drilling fluid are caused. Regarding the drilling variables, many factors cause the decrease or increase of the loss, the most important of which are the weight on the drill bit, drilling speed, the rate of... 

Demand for the petroleum products is continuously increasing. Crude oil cannot be used as it is extracted, so that, there should be some treatment that may ended up producing heavy hydrocarbons. Therefore, refineries are searching for developing new technologies for upgrading those heavy materials and convert more and more bottom-of-the-barrel into high value distillate. Amongst the different residua upgrading processes, thermal upgrading processes are of the most interest and account for over 60% of total residua processing capacity. In this work, we investigate the effect of different additives in a delayed coking process. We used vacuum distillation residue of Abadan heavy crude oil... 

Lead-acid batteries have been used for over 150 years as a reliable means of storing electrical energy. These batteries have a variety of applications due to their high safety, reliable performance, and relatively easy manufacturing process, including in car starters, car lighting and combustion, electric vehicles (especially electric bicycles), and the resulting electrical energy storage. From renewable sources or pulsed power supplies in hybrid electric vehicles. Despite increasing advances in the performance and design of these batteries, there are still problems in this area. One of the most important of these is the electrolysis of water as a side reaction, which leads to the production... 

Additive manufacturing (Simply called A.M.) is a group of manufacturing technologies that is developing rapidly and is being used widely in some industries like car manufacturing, Aerospace and producing Biomedical devices, In a way that some researchers believe that A.M. methods will change the future of manufacturing. One of the most important A.M. techniques is the Selective Laser Sintering (SLS) method that is mostly used in industrial applications. A SLS machine has a lot of sub systems and mechanisms that have key role in the Laser Sintering process. One of the mechanisms of SLS machine is the Powder Dispensing mechanism that produce layers of unsintered powder as thin as 100 microns... 

Acidizing efficiency depends on various factors such as formation properties, reservoir and stimulation fluid types and injection scenario. Among these factors, heterogeneity of reservoir’s formation (layered reservoirs and permeability variation versus depth) strongly affect acidizing performance. Accordingly, applying a reliable technique that distribute stimulation fluid uniformly is essential. The aim of carbonate matrix acidizing is to improve fluid flow specially in low permeability zones. Stimulation fluid cannot enter into the low permeability layer due to existence of high permeability layers which are in contact with low permeability ones. So, the stimulation fluid should be... 

In this study, the zirconia antistatic coating was synthesized by dip coating sol-gel route on glass substrate. The solution contains ZrCl4 as precursor and isopropanol as solvent to synthesize zirconium oxide. The effects of environmental humidity and solution concentration on the coating characterization were analyzed. MPTS and primer binder were added as binding agents in the solution to observe the effect of binding agents on the coating adhesion. Solution stability and antistatic coating characterization were analyzed by zita potential test, FTIR spectroscopy, EDX analysis, FESEM and AFM microscopy, pencil hardness test, thickness test, antidust ability and spectrophotometer. The...