Sharif Digital Repository

Turbidity currents are produced when a particle laden fluid flows under the lighter ambient fresh fluid. The streaming of particle laden fluid is called turbidity current and this kind of currents is the major mechanism for sediment transportations in lakes and oceans. In the present research, the main concentration is on the effect of obstacle on the behavior of turbidity current. A series of laboratory experiments were carried out with various obstacle heights, shapes and different inlet densimetric Froude numbers. In each experiment, velocity profiles upstream and downstream of the obstacle were measured, using an ADV (Acoustic Doppler Velocimeter). Kaolin was used as the suspended... 

In small settling tanks, the sludges can be removed using perforated pipes. In this method the pipe is placed in the depth of a fluid and the lateral inflow through perforations lead to the outlet. Since there are few researches about hydraulic characteristic of perforated pipes, this research will investigate the hyadraulic characteristic of these pipes experimentally. One of the main objectives of these pipes is to use the entire lenghte of the pipe and also provide the uniform distribution of inflow. In the past studies, it was found out that inflow mostly comes through downstream perforations. The objective of this research is to find the distribution of discharge along the perporated... 

The behavior of boundary layer under the effect of the sweep angle is considered. The measurements were performed by a pitot tube rake. Three models with various sweep angels at angles of attack -2, 0 and 2 degree were tested. Both tip and root of all wings were closed by flat plates in order to prevent the flow to roll-up. However the flow field on the wing was still three-dimensional because of the sweep angle. The velocity on the wing has two components; longitudinal and lateral. The cross flow emerges due to the non-equilibrium of pressure and centrifugal forces. The velocity profiles showed that the magnitude of cross flow was stronger near the leading edge of the wing. The cross flow... 

Chemical flooding such as surfactant flooding in oil reservoirs can change the wettability and interfacial tension between oil and water and so reduce the residual oil saturation in the reservoir. Some of these materials can be adsorbed a lot on the surface of carbonate rocks, so it is difficult to predict the oil recovery factor in such process. Therefore it is necessary to survey the adsorption amount of surfactants in chemical EOR injections.In this thesis, the adsorption of a nonionic surfactant on the surface of carbonate rock is experimented and the proper model is obtained. Then the surfactant is injected in a core saturated with oil to observe the efficiency of this surfactant in... 

In this thesis the effects of vibro absorbing coating on vibration behavior of an aluminum sheet and also on a stiffened aluminum panel are investigated using experimental approach. Since there wasn't any information available about the used coating, to find its viscoelastic material properties, the method mentioned in ASTM E756-05 standard is employed and corresponding tests are performed.
In the next step, an analytical solution developed for the aluminum sheet with viscoelastic coating and the obtained results compared with experimentation, in order to find its prediction accuracy for loss in “loss factor” of the system in presence of coating.
To study the effect of... 

Transonic flow study is important due to its vast applications. Supercritical airfoils are designed for transonic flow to postpone drag divergence and reduce the strength of shock. This type of airfoils are chiefly used in modern commercial airplanes because of their low drag in transonic regime and, as a result, reduction in their fuel consumption. Using supercritical airfoils needs accurate investigation of flow field due to several influential factors such as specific geometry, nonlinear nature of flow phenomena, and compressibility effects. However, the availability of experimental and numerical data for supercritical airfoils is less than that of the conventional ones. Thus,... 

In the present study, it has been tried out to increase the hardness and wear resistance of anodized aluminum coating byadding Si3N4 nanoparticles to the anodizing bath and making a composite coating. In order to investigate the influence of other effective parameters on the properties of anodized coating before the compositing process, hardness and thickness were optimized in the Sulphoric/oxalic bath using design of experimental method (central composite design). The properties of these coatings are dependent on various parameters among which time, temperature and pulse current parameters (current density limit, frequency and duty cycle) were considered in the present study. Analysis of... 

Limited fossil resources, daily increase of demand for energy and the most important one that is environmental pollution fact, make people think of renewable energy as a solution. One type of these renewable energies is offshore wind energy that has high potential without any sound and visual noises. Recently a lot of researches have carried out their studies on the topic of offshore wind turbine. Cause of disabling of a lot of software to simulating of dynamic effect of rotating rotors, so in this research has make effort to fabricate and test an offshore wind turbine with different rotor rotating velocities and different heading angle of wind, to catch the effect of these parameter on the... 

Expanded polystyrene (EPS) products are mostly manufactured as disposable products, designed for a single use after which are recycled or disposed as solid wastes. EPS products are increasingly used specially in form of food containers and packing blocks and most of the time are left in nature without any kind of processing, causing environmental pollution. This project intends to investigate physical characteristics of lighter cement concrete with acceptable compressive strength for non-structural elements, made with different percentages of recycled EPS beads. A group of concrete samples are made by replacing coarse aggregate with equivalent volume of recycled EPS beads. Properties like... 

Gravity currents are a general class of flows in which the density difference between two fluids drives the flow. Turbidity currents are gravity currents in which the density difference is due to suspended sediment. Reservoir sedimentation is mainly occurs because of sediment transport by these currents. If turbidity currents can be stopped in a reservoir, or influenced in such a way that the sediments are not deposited in critical locations like bottom outlets, the storage capacity of the reservoirs can be increased considerably. In order to do this, various methods such as placing an obstacle in the path of these flows have been proposed. In this study, the effect of inlet sediment... 

The problem of attitude determination (AD) has always been a challenging issue for space missions that is of importance either independently or for attitude control purposes. The problem of AD is generally focused from two aspects: measurement mechanisms (sensoring) and determination algorithms. From the former point of view, there exists a variety of measuring systems such as the Sun sensors, magnetometers, gyroscopes, star and horizon sensors that have been separately or collaboratively utilized for AD. Integrative usage of sensors not only can bring about added advantages in terms of accuracy, but also provides for estimates of attitude during special times such as the Sun eclipse. The... 

This study presents a novel perspective on pressure-transient analysis (PTA) of downhole-pressure and flow-rate data by use of system-identification (SI) techniques as widely used in advanced process engineering. Key features of the algorithm are that it considers the classic PTA process from a system-theoretical perspective; derives the causal structure of the flow dynamics; proposes a method to deal with continuously varying pressure and flow-rate signals contaminated with correlated noise, which estimates physical reservoir parameters through a systematic matching procedure in the frequency domain; and can cope with arbitrary (i.e., not necessarily piecewise constant) flow-rate signals.... 

The simulation of hydro-pneumatic systems should be considered as a difficult task, because they consist of several different hydraulic and pneumatic components working together and affecting each other. For example, hydraulic and pneumatic components interact strongly in a diaphragm pump. As known, a single liquid phase may unwantedly change to two-phase condition and cause unavoidable problems within the simulation processes. In this research, we simulate the unsteady multiphase flow in high pressure hydro-pneumatic systems using a hybrid numerical-experimental method to study such rather complex effects suitably. For the computational fluid dynamics part of the simulation, we use a single... 

Matrix acidizing as a well stimulation technique is performed to increase the production index by increasing the permeability and removing the formation damage in the near wellbore region. However, several challenges such as corrosion of the tubulars and iron precipitation in the formation are hindering this process. To encounter these challenges, different chemicals, or additives, such as corrosion inhibitors and iron control agents are added to the acid solution. Carbonate acidizing has been carried out using HCl-based stimulation fluids for decades. However, at high temperatures, HCl does not produce satisfactory results because of its fast reaction, acid penetration, and hence surface... 

For several decades, turbocharging of internal combustion engines has been a wide spreading technology to increase the engine output power as much as possible. Turbocharger has two main components: compressor, and turbine. Therefore, increasing the efficiency of turbine and compressor has a major role in engine performance improvement. This has been a continuous research goal in 20th century. Considerable advances has been achieved until now. Turbocharger turbine should be matched to engine in a wide range operation conditions with high efficiency. Many researchers have published their achievements considering turbine elements design improvements. This research is focused on the turbine... 

In this study performance of tack coat (thin layer bonding asphalt concrete layers) was evaluated. The shear strength of tack coat layer was considered as its measure of performance. Direct shear tests were conducted on two layered HMA specimens. The test variables included the type of tack coat material, application rate (amount of residual bitumen per unit area), substrate condition, normal stress and shear loading rate. Four types of liquid asphalt (CSS, CRS, modified CRS and MC-250) were applied as tack coat. Three substrates conditions were used in the tests. These were 3-days old, 17-days old and long term aged substrates were used. It was found that optimum application rate depends... 

Heat transfer in porous media has recently become an important subject in mechanical engineering. Heat transfer in porous media is central in many applications involving industrial devices (chemical engineering, heat exchangers, nuclear reactor, etc...) as well as complex geological formations (in situ combustion and pyrolysis, geothermal sites, etc...). On track to achieve heat transfer methods and heat transfer coefficients of porous materials, this investigation describes the design process of fabrication and experimental analysis of calculation the conduction heat transfer coefficient of the uniform porous materials. We report on thermal conductivity measurements performed on uniform... 

This study is a report on the fabrication of a novel single-chamber micro-structure microbial fuel cell consisting of spiral anode chamber. A 3×3 cm plexiglass plate with 1 mm thickness was used as main body. A spiral microchannel (1 mm in width and 226 mm in length) was cut using a laser beam as an anodic compartment. Two types of microbial fuel cells with the same anode electrode (stainless steel mesh) and different cathode electrodes (stainless steel mesh and carbon cloth) were constructed in order to investigate the effect of cathode electrode material on microbial fuel cell performance. In both batch and continuous mode, higher power density was obtained by microbial fuel cell with... 

During the last six decades, there were remarkable developments in the field of gas turbines. In the early 1950’s, the effciency of gas turbines was 20% and it is improved up to more than 40% for modern gas turbines. In addition, due to the implementation of the combined power cycles, the thermal effciency have been reached to 60%. According to the recent developments, further improvements in this field seem to be more costly and diffcult to obtain. Rotating detonation combustor (RDC) is a new generation of detonation combustors which has simpler design and several advantages compared to jet engine combustors, but it has its intrinsic problems which seem resolvable. Given that the RDC... 

In many cases, oil and gas extraction from reservoirs due to damage and permeability reduction near wellbore is lower than optimum level and reduces the flow of oil into the well. In fact, formation damage is the collapse of natural condition of reservoirs, In addition to delaying production and increasing costs, it causes early desertification of wells. Well stimulation methods are used to solve this problem and increase production. One of the most effective ways to increase the production of wells is well acidizing. In this study, the acid performance of the fractured carbonate reservoirs has been investigated. In this type of reservoirs, due to the existence of high permeable paths of the...