Sharif Digital Repository

A coupled cellular automata and finite element model has been proposed to evaluate static recrystallization kinetics during non-isothermal annealing of cold deformed low carbon steels. The effects of various factors including heating rate, annealing temperature, and initial microstructures have been considered in the model to accurately predict the static recrystallization kinetics and the final microstructures. In order to examine the employed algorithm, the predicted results have been compared with the experimental observations and a good agreement was found between the two sets of results  

Storage tanks are always under different hazards such as corrosion and leaking. In this work we have introduced a computational analysis on storage tanks in which a real-time yet efficient monitoring technique using Fiber Bragg Grating (FBG) sensors for corrosion detection on the bottom plate and vibration monitoring on outer surfaces of storage tanks is proposed. A finite element model for the tank is developed, in which the outer tanks surfaces are considered as plate elements and FBG sensors as beam elements. An array of FBG sensors is utilized to compute the generated strain in the FBGs due to losing thickness in the tank's bottom plate and due to vibration on the outer surfaces in... 

The present study aims to challenge the existing finite element models in terms of one of the most important practical parameters, i.e. coverage. Important models from the literature are re-simulated and their resulted treated surfaces are carefully examined. Result of this study shows that existing finite element models could not reflect the realistic coverage. A variable dimension symmetry cell is developed in order to acquire full coverage and at the same time not increasing the computational cost. This model can successfully simulate the surface nanocrystallization by severe shot peening in which the amount of coverage is much higher than conventional shot peening  

In this paper the finite element model of the Brushless Doubly-Fed Machine is presented. A magnetodynamic finite element model allowing the simulation of the healthy and faulted machine with its special rotor topology is extracted and simulated. To verify the validation of the proposed model the results are compared with couple circuit model, which used generalized harmonic theory  

Special superelements are often used to improve the computational efficiency and improve accuracy of finite element modeling. Structures with tapered and spherical geometry exist in many engineering problems. In this work, special tapered and spherical superelements are presented that can be used for modeling of tapered and spherical bodies in thermo mechanical analyses with computational efficiency. The performance of these superelements under thermal and structural loads is demonstrated by presenting several examples and comparing the results with those from conventional 3D brick elements, which shows high accuracy at reduced computational cost  

In this study, influences of intermolecular forces on dynamic pull-in instability of electrostatically actuated beams are investigated. Effects of midplane stretching, electrostatic actuation, fringing fields and intermolecular forces are considered. The boundary conditions of the beams are clamped-free and clamped-clamped. A finite element model is developed to discretize the governing equations and Newmark time discretization is then employed to solve the discretized equations. The results indicate that by increasing the Casimir and van der Waals effects, the effect of inertia on pull-in values considerably increases  

Laparoscopic surgery is a Minimally Invasive Surgery (MIS) procedure which is performed in the abdominal cavity. In this paper, the spleen tissue and a laparoscopic surgical grasper were modeled using ABAQUS software to investigate the tool-tissue interaction, considering large deformations for the spleen tissue. The spleen tissue was modeled as a hyper-elastic material. The laparoscopic grasper includes three gripping jaws that always remain parallel. The sliding can occur between the gripping jaws and the spleen tissue. It was found that the relationship between the pinch forces and push forces keeps its linearity in different values of friction coefficient (0-0.3). The pushing force... 

In this study, dynamic pull-in instability and snap-through buckling of initially curved microbeams are investigated. The microbeams are actuated by suddenly applied electrostatic force. A finite element model is developed to discretize the governing equations and Newmark time discretization is employed to solve the discretized equations. The static pull-in behavior is investigated to validate the model. The results of the finite element model are compared with finite difference solutions and their convergence is examined. In addition, the influence of different parameters on dynamic pull-in instability and snap-through buckling is explored  

Steel box girders have two webs and two flanges on top that are usually connected with shear connectors to the concrete deck and are also known as tub girders. The end diaphragms of such bridges comprise of a stiffened steel plate welded to the inside of the girder at each end. The diaphragms play a major role in transferring vertical and lateral loads to the bearings and substructure. A review of literature shows that the cyclic behavior of diaphragms under earthquake loading has not been studied previously. This paper uses a nonlinear finite element model to study the behavior of the end diaphragms under gravity and seismic loads. Different bearing device and stiffener configurations have... 

This paper discusses the necessity of considering the concurrent effects of uniform temperature and earthquake loadings in the design of cable-stayed bridges. This load combination is not foreseen in current design standards such as AASHTO and Eurocode. Three-dimensional finite element models of cable-stayed bridges are employed for nonlinear time history analyses. A load combination is proposed that adds uniform temperature loading to the existing extreme event load combination. The proposed combination is compared with existing extreme event load combination and the changes in forces and displacements are noted. A parametric study is then conducted by varying a number of properties of the... 

In this research, an extended finite element model has been investigated. Investigation of opening and closure stress always has been one of the difficult parameters to analysis of results; therefore, the utilization of finite element methods would be a good and logical alternative for this purpose. In addition, linear elastic fracture criteria are used for validation of numerical results from the simulation. In this work, a detailed analysis of the influence of different parameters in the results of a specific specimen with a semi-elliptical tooling groove in terms of closure and opening stress is presented, and the impact of optimum element size in fracture characteristic in various load... 

A number of geometrically-detailed passive finite element (FE) models of the lumbar spine have been developed and validated under in vitro loading conditions. These models are devoid of muscles and thus cannot be directly used to simulate in vivo loading conditions acting on the lumbar joint structures or spinal implants. Gravity loads and muscle forces estimated by a trunk musculoskeletal (MS) model under twelve static activities were applied to a passive FE model of the L4-L5 segment to estimate load sharing among the joint structures (disc, ligaments, and facets) under simulated in vivo loading conditions. An equivalent follower (FL), that generates IDP equal to that generated by muscle... 

Ligaments assist trunk muscles in balancing external moments and providing spinal stability. In absence of the personalized material properties for ligaments, finite element (FE) models use dispersed data from the literature. This study aims to investigate the relative effects of eight different ligament property datasets on FE model responses. Eight L4-L5 models distinct only in ligament properties were constructed and loaded under moment (15. N. m) alone or combined with a compressive follower load (FL). Range of motions (RoM) of the disc-alone model matched well in vitro data. Ligament properties significantly affected only sagittal RoMs (∼3.0-7.1° in flexion and ∼3.8-5.8° in extension at... 

This paper deals with the generalized coupled thermoelastic solution for disks with constant thickness. It is a sequel to the authors's previous work in which refined 1D Galerkin finite element models with 3D-like accuracies are developed for theories of coupled thermoelasticity. Use of the reduced models with low computational costs may be of interest in a laborious time history analysis of the dynamic problems. In this paper, the developed models are applied and evaluated for a 3D solution of the dynamic generalized coupled thermoelasticity problem in the disk subjected to thermal shock loads. Comparison of the obtained result with the results available in the literature verified the... 

Ligaments assist trunk muscles in balancing external moments and providing spinal stability. In absence of the personalized material properties for ligaments, finite element (FE) models use dispersed data from the literature. This study aims to investigate the relative effects of eight different ligament property datasets on FE model responses. Eight L4-L5 models distinct only in ligament properties were constructed and loaded under moment (15 N m) alone or combined with a compressive follower load (FL). Range of motions (RoM) of the disc-alone model matched well in vitro data. Ligament properties significantly affected only sagittal RoMs (∼3.0–7.1° in flexion and ∼3.8–5.8° in extension at... 

A comprehensive non-linear finite element (FE) model of integral abutment bridges (IABs) is presented to facilitate the analysis of such bridges using commercial software, especially under seismic loading. The presented model is capable of capturing non-linearity in both the structure and soil, in addition to considering far-field soil response. The model is simple enough to be used for practical purposes. On the other hand, many aspects of seismic behaviour of IABs are unclear, due to complicated soil–structure interaction. Using the presented model, a parametric study is performed to identify the effects of bridge length, abutment type and soil type on seismic behaviour of IABs. Non-linear... 

A number of geometrically-detailed passive finite element (FE) models of the lumbar spine have been developed and validated under in vitro loading conditions. These models are devoid of muscles and thus cannot be directly used to simulate in vivo loading conditions acting on the lumbar joint structures or spinal implants. Gravity loads and muscle forces estimated by a trunk musculoskeletal (MS) model under twelve static activities were applied to a passive FE model of the L4-L5 segment to estimate load sharing among the joint structures (disc, ligaments, and facets) under simulated in vivo loading conditions. An equivalent follower (FL), that generates IDP equal to that generated by muscle... 

Transient thermal field in laser surface hardening treatment of medium carbon steel was analyzed by employing both three-dimensional analytical model and finite element model. In finite element model the laser beam was considered as a moving plane heat flux to establish the temperature rise distribution in the work-piece, while in analytical model laser beam was considered as an internal heat source. The numerical results were compared with the analytical results. In laser heat treatment of steel some methods are used to produce a wider and nearly uniform average irradiance profile. It may be achieved by rotating the beam optically, thereby producing an overlapping spiral track, or by... 

As steel plate shear walls are typically used in the building central cores around the elevators and stairs, introduction of an opening as door seems to be inevitable in steel plate shear wall spans. Due to the weakening of the steel plate shear walls’ performance caused by this particular type of opening, the use of stiffeners around the opening is necessary. Nevertheless, introduction of stiffeners around all sides of the opening, which does continue to boundary elements, is very expensive and inefficient. Therefore, the study on the effect of different arrangements of stiffeners on the behavior of steel plate shear walls is significant. In this research, a number of steel plate shear... 

In the selective laser sintering (SLS) method, layers of powder are scanned by a laser beam and sintered. The thermal gradients created by laser heating and the subsequent cooling of the sintered sections results in thermal stresses and part warping in the final part. Thermal gradients are dependent on the scanning algorithm, in particular, the scan vector length. In this work, an efficient scanning algorithm for the SLS process is presented with the aim to minimise the part warping in the final part due to thermally induced residual stresses, while maintaining the production time at a minimum. The proposed algorithm is implemented in a finite element simulation and scanning parameters...