Sharif Digital Repository

In order to define a new temperature correction factor in this study, accurate experimental values were presented for permeability and diffusivity of carbon dioxide and methane in imidazolium-based room temperature ionic liquid: [bmim][PF6] (1-butyl-3-methylimidazolium hexafluorophosphate) immobilized on an inorganic membrane support. Results were presented as a function of temperature and pressure for temperatures within 300-320K and pressures below 50kPa. According to the literature, experimental values of permeability and diffusivity for CH4 in [bmim][PF6] vs. temperature are reported for the first time in this study. Results obtained for CO2 permeability revealed good agreement with data... 

In this paper, dynamic ageing characteristics associated with the application of equal channel angular pressing (ECAP) to Al6061 alloy at elevated temperatures was investigated. Followed by ECAP, Vickers microhardness measurement on the cross-sectional planes and microstructural observations were undertaken using transmission electron microscopy. The combination of the ECAP process with dynamic ageing at both 100°C and 150°C resulted in a significant increase in hardness. The grain size was measured as ∼160. nm after four passes. A comparison with the published data on the same alloy processed by ECAP at room temperature and statically aged, suggests several advantages in incorporating... 

We prepared Cu nanoparticles in a-C:H thin films by co-deposition of RF-sputtering and RF-PECVD methods at room temperature. By increasing Cu content in these films a nonmetalmetal (NM) transition is observed. This transition is explainable by the power law of percolation theory. The critical metal content is obtained 56% and the critical exponent is obtained 1.6, which is larger than the exponent for 2 dimension systems and smaller than the one for 3 dimension systems. The electrical conductivity of dielectric samples was explained by tunneling. Activation tunneling energy that was obtained from temperature dependence of electrical resistivity correlates with near infrared absorption peak... 

Equal channel angular pressing is an outstanding method for imposing large plastic deformation to metallic materials without any decreasing in cross section area of as processed samples. In this paper, the effect of working temperature, ram speed and the number of passes on the formation of adiabatic shear bands in Al6061 during equal channel angular pressing was investigated. Billets of the alloy were processed up to four passes via route BC from room temperature to 200°C with two ram speeds using a die that imparts an effective strain of ∼1.1 per pass. The results have demonstrated that the onset of the adiabatic shear banding in this alloy strongly depends on the ram speed: more... 

We present gas sensing property of carbon nanotubes (CNTs) polymethylmethacrylate (PMMA) composite as the active element for acetone vapour detection at room temperature. The polymeric films were formed by spin coating method on SiO2 substrates. Then they were activated by dropping the CNTs suspension in acetone on the PMMA films. The CNT/PMMA films were characterised by SEM, TEM and Raman spectroscopy. Variation of film's electrical resistance after exposure polar and non-polar gases is utilised as the principle of gas sensing. The experimental results showed that the samples present chemical selectivity and reversibility toward polar gases especially acetone vapour  

In this study, effect of rolling speed on strain aging phenomena in warm rolling of a carbon steel has been investigated. For this purpose, by using a mathematical model and predicting temperature and strain rate fields, the possibility of occurrence of dynamic strain aging during the warm rolling was first evaluated. In the next stage, warm-rolled samples were aged up to 11 months at room temperature for studying the kinetics of static strain aging, while mechanical tests as well as microstructural evolutions have been performed to determine the effect of strain aging on material behavior. The results indicate that dynamic strain aging may not occur for the employed rolling program;... 

Dual-phase (DP) steels with different martensite contents were produced by subjecting a low carbon steel to various heat treatment cycles. In order to investigate the effect of dynamic strain aging (DSA) on mechanical properties, tensile specimens were deformed 3% at 300 °C. Room temperature tensile tests of specimens which deformed at 300 °C showed that both yield and ultimate tensile strengths increased, while total elongation decreased. The fatigue limit increased after pre-strain in the DSA temperature range. The effects of martensite volume fraction on mechanical properties were discussed  

Through a fast, simple, low cost, surfactant-free and convenient microwave-assisted route, narcis-like ZnO nanostructures (10-15 nm size) with flower diameters in the range of 1-2.5 μm were synthesized. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy and room temperature photoluminescence (PL) measurements were used to characterize the produced ZnO nanostructures. The principle raw materials - ammonium hydroxide (NH4OH) and zinc acetate dihydrate [Zn(CH3COO)2·2H2O] - were both inexpensive. The method was fast, simple and surfactant-free capable of producing larger quantities of zinc oxide... 

A manganese(II) complex of 2,4,6-tris(2-pyridyl)-1,3,5-triazine (tptz) has been synthesized and characterized by single-crystal X-ray diffraction, elemental analyses, IR, and UV-Vis spectroscopic techniques. Oxidation of alcohols to their corresponding aldehydes and ketones was conducted by this catalyst using oxone (2KHSO5KH-SO4K2SO4) as an oxidant under biphasic reaction conditions (CH2Cl2/H 2O) and tetra-n-butylammonium bromide as phase transfer agent under air at room temperature. Easy preparation, mild reaction conditions, high yields of the products, short reaction times, no further oxidation to the corresponding carboxylic acids, high selectivity and inexpensive reagents make this... 

Utilizing the so-called tube spinning, a cold-bonding process entitled as "spin-bonding" is developed to produce seamless thin-walled clad tubes and cylinders. By this method, two layers of AA 1050 tubes were successfully bonded together to form a clad tube at room temperature. Based on mechanical aspects of the tube spinning process, the mechanism of spin-bonding is explained in two stages: surface preparation before occurrence of a stable bond and bond strengthening thereafter. The effects of process temperature, thickness reduction, feed rate and roller attack angle as the parameters of tube spinning on the bond strength are studied. It is shown that the bond strength increases by... 

4340 steel bars were austenitized at 850°C for 1 hour followed by heating at 700°C (ferrite and austenite region) for 90 min and quenching into a salt bath with different temperatures of 300, 350, 400 and 450°C. The steel bars were held for 1 hour at these temperatures before air cooling to room temperature. Various ferrite-bainite microstructures with 34% volume fraction of ferrite and different bainite morphologies were obtained. The results of SEM studies showed that by increasing the austempering temperature, the morphology of bainite varies from lower to upper bainite. According to the T-T-T diagram of the studied steel, the bainite transformation will not complete for the holding time... 

In this paper, considering the problems of common finite element (FE) codes that consider simple constitutive equations, a developed FE code that considers a new constitutive model is used to simulate the behavior of copper sheets under severe plastic deformation (SPD). The new proposed constitutive model, that considers dislocation densities in cell interiors and cell walls of material as true internal state variables, can investigate all stages of flow stress evolution of material during large plastic deformations and also can explain the effects of strain rate magnitude on the mechanical response of material, during room temperature SPD. The proposed FE analysis is used to investigate the... 

N-Benzyl-DABCO tribromide, a stable, solid organic ammonium tribromide, has been used as a bromine source for the regioselective and high-yielding bromination of aromatic amines and phenols. Mono-bromination proceeds well in the presence of a stoichiometric amount of bromine source at room temperature  

In this study by using a capacitive cell probe the temperature variation of the electrical properties of the water liquids is investigated. Variation of the reactance capacitance parameter of liquids with temperature in the range of 17-60°C is measured for the plain water and water mixtures. The temperature variations of the capacitance for the cool distilled and tap water samples are studied for the range of 17-29°C obtained. Present results indicate an averaged variation of 4.69 μF/°C for the distilled water and 3.24 μF/°C for tap water in warm up process to a near room temperature. The cooling behaviors for the warm mineral, tap and salt water liquids are also investigated in this study.... 

At room temperature, SO 2- 4/nano-TiO 2 efficiently catalyze the direct Mannich-type reaction of varieties of in situ-generated aldimines using aldehydes and anilines with ketones in a three-component reaction under solvent-free conditions. The reaction proceeds rapidly and affords the correspondingβ-amino ketones in good to high yields with good to excellent stereoselectivity. The catalyst can be recycled for subsequent reactions without any appreciable loss of efficiency  

Na0.3WO3 1D nanostructure forms (nanorods and nanobelts) were grown by a solid-liquid-solid mechanism from a 40 nm sputtered tungsten film deposited on a soda-lime substrate and annealed at 700 °C in a tubular furnace in N2 ambient. The morphology, structure, composition and chemical state of the prepared nanostructures were characterized by SEM, XRD, TEM, SAED and XPS measurements. The Na0.3WO3 1D nanostructures were found to have a cubic crystalline structure and grown along the [0 0 1] direction. The nanorods are a few micrometres in length and about 50 nm in diameter. The field-emission application of the prepared samples at different distances between the cathode and the anode was... 

Different microstructures were produced by heat treatment of 4340 steel. These microstructures are bainite, martensite, ferrite-martensite and ferrite-bainite. Mechanical tests were carried out at room temperature. The results showed that steel with bainite-ferrite microstructure has better ductility and charpy impact energy than steels with martensite-ferrite and full bainite microstructures. But yield and tensile strengths of this steel are less than the yield and tensile strengths of the other two steels. Hardness measurements showed that their hardness is the same. Fracture surface observations of tensile specimens showed increase in toughness of bainite-ferrite in comparison to... 

Synchronous heterogeneous catalytic hydrogenation of cyclohexene and acetone, catalyzed by Pt/Al2O3, was carried out in solutions of 2-hydroxy ethylammonium formate (a room temperature ionic liquid, RTIL) with ethanol and propan-1-ol at 25 °C. Rate constants and selectivity of the reaction (relative to cyclohexene hydrogenation) increase with mole fraction of the ionic liquid (IL). The reactants tendency to the catalyst surface increases by addition of the ionic liquid and thus the reaction rate increases, especially for cyclohexene hydrogenation. Consequently the selectivity to cyclohexene hydrogenation was increased. Single-parameter correlations of log k vs. π* (dipolarity/polarizibility)... 

In this work we report a new thermochemical method for the synthesis of ZnS:Mn nanocrystals. Zn(NO3)2 and Na2S 2O3 were used as the precursors and Mn(NO 3)2 was the source of impurity. Thioglycerol (TG,C 3H8O2S) was also used as the capping agent and the catalyst of the reaction. Na2S2O3 is a heat sensitive material which releases S species upon heating. Consequently, the reaction proceeds in temperatures higher than room temperature. The reaction was done in two steps. In the first step, the precursors were heated at 96 °C for an hour without TG. In the second step, TG was injected to the solution and the heating process was continued for longer heating durations. A fast growth occurred in... 

NiTi shape memory alloy (SMA) ingots were produced by vacuum induction melting/casting unit. The effect of microstructure on the hot (1000C) and cold (room temperature) rolling workability of cast samples was investigated. Microstructure of the cast samples was related to the type of crucible which used for melting and the average vacuum pressure of VIM furnace. Optical microscope, scanning electron microscope (SEM), and energy dispersive technology (EDS) methods were used to inspect the origins of observed cracks after rolling processes. The results showed that the formation of both Ti4Ni2O and TiC impurities formed due to inappropriate melting conditions had detrimental effects on...