Sharif Digital Repository

4340 steel bars were austenitized at 850°C for 1 hour followed by heating at 700°C (ferrite and austenite region) for 90 min and quenching into a salt bath with different temperatures of 300, 350, 400 and 450°C. The steel bars were held for 1 hour at these temperatures before air cooling to room temperature. Various ferrite-bainite microstructures with 34% volume fraction of ferrite and different bainite morphologies were obtained. The results of SEM studies showed that by increasing the austempering temperature, the morphology of bainite varies from lower to upper bainite. According to the T-T-T diagram of the studied steel, the bainite transformation will not complete for the holding time... 

In this paper, considering the problems of common finite element (FE) codes that consider simple constitutive equations, a developed FE code that considers a new constitutive model is used to simulate the behavior of copper sheets under severe plastic deformation (SPD). The new proposed constitutive model, that considers dislocation densities in cell interiors and cell walls of material as true internal state variables, can investigate all stages of flow stress evolution of material during large plastic deformations and also can explain the effects of strain rate magnitude on the mechanical response of material, during room temperature SPD. The proposed FE analysis is used to investigate the... 

The sol gel method was employed to prepare peroxopolytungstic acid (P-PTA). Palladium chloride salt was dissolved in the sol with different Pd:W molar ratios and coated on Al2O3 substrates by spin coating method. XRD and XPS techniques were used to analyze the crystal structure and chemical composition of the films before and after heat treatment at 500 °C. We observed that Pd can modify the growth kinetic of tungsten trioxide nanoparticles by reducing the crystallite size and as a result can improve hydrogen sensitivity. Resistance-sensing measurements indicated sensitivity of about 2.5 × 104 at room temperature in hydrogen concentration of 0.1% in air. Considering all sensing parameters,... 

Dual phase (DP) steels with network and fibrous martensite were produced by intercritical annealing heat treatment cycles. Some of these steels were deformed at dynamic strain aging temperatures. Room temperature tensile tests of specimens deformed at 300 °C showed that both yield and ultimate tensile strengths for both morphologies increased, while total elongation decreased. Fatigue test results before and after high temperature deformation showed that dynamic strain aging has a stronger effect on fatigue properties of dual phase steels with fibrous martensite. Cracks in DP steels with fibrous martensite propagate in a tortuous path in soft ferrite phase, while they pass of both hard and... 

We report experimental evidence of Cu surface segregation in Ni/Cu system, during deposition of Ni film onto Cu substrate at room temperature and during heat treatment in vacuum. Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) by Tougaard's analysis results show that surface segregation defeats in competition with increase in Ni thickness and terminates when thickness of Ni increase to more than 4 nm. Surface energy and concentration were calculated using contact angle measurements and the results confirm that segregation reduces the surface energy. Surface segregation during heat treatment at 150-220 °C range as a function of time initially shows linear mass... 

A novel class of substituted quinazolines were prepared in good yields by a one-pot three-component reaction of isocyanides with adducts of anilines and tri- or dichloroacetonitrile, followed by intramolecular C-H activation, catalyzed by copper(I) iodide with l -proline as a ligand in acetonitrile at room temperature. © 2017 Georg Thieme Verlag Stuttgart .New York-Synlett  

Perovskite solar cells with an inverted p-i-n architecture were constructed under ambient conditions by employing materials of lower cost than standard cells. Thus, graphene oxide was used as a hole transporting material and Li-modified graphene oxide as an electron transporting material, while Al was used as a counter electrode. A maximum solar conversion efficiency of 10.2% was achieved by adding a Ti-based sol on the top of the Li-modified graphene oxide layer. © The Royal Society of Chemistry  

Gas permeation through nanoscale pores is ubiquitous in nature and has an important role in many technologies 1,2 . Because the pore size is typically smaller than the mean free path of gas molecules, the flow of the gas molecules is conventionally described by Knudsen theory, which assumes diffuse reflection (random-angle scattering) at confining walls 3-7 . This assumption holds surprisingly well in experiments, with only a few cases of partially specular (mirror-like) reflection known 5,8-11 . Here we report gas transport through ångström-scale channels with atomically flat walls 12,13 and show that surface scattering can be either diffuse or specular, depending on the fine details of the... 

The synthesis of functionalized benzothiadiazine 1,1-dioxide derivatives was achieved through a novel three-component intramolecular C–H activation reaction of trichloroacetonitrile, benzenesulfonyl chloride, and various primary amines. This reaction was performed in the presence of catalytic copper(I) and L-proline as the ligand in tetrahydrofuran at room temperature. © 2018 Elsevier Ltd  

The first example of a heterogeneous catalytically active system for Buchwald–Hartwig and Ullmann homocoupling of unactivated aryl halides (fluorobenzene) is presented. The novel magnetic heterogeneous palladium catalyst was synthesized by immobilization of palladium ions onto an aminopyridine-functionalized Fe3O4. The catalyst was fully characterized by FTIR spectroscopy, temperature-programmed reduction, thermogravimetric analysis, CHN elemental analysis, transmission electron microscopy, field-emission scanning electron microscopy, X-ray diffraction, energy-dispersive X-ray spectroscopy, and atomic absorption spectroscopy. By using this catalyst system, various types of primary and... 

A typical Cobalt-Copper ferrite nanoparticles (CoCuFe2O4) was used as a catalyst for one-pot [3+2] cycloaddition of alkyl azides with alkynes at room temperature in green media. These nanoparticles were synthesized by using co-precipitation method and were fully characterized by physiochemical technique. By this catalyst system, various types of alkyl halides were coupled with alkynes efficiently to furnish 1,2,3 triazoles in excellent yields within short reaction time. The requirement on energy and time for the Click reaction extremely minimized in this method compared to previously reported reactions as an inevitable trend in development of green chemistry. Using green solvent, inexpensive... 

An eco-friendly gold-based catalyst supported on proline decorated montmorillonite was synthesized. The catalyst was characterized by combination of Fourier-transform infrared spectroscopy (FT-IR), Field Emission Scanning Electron Microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Brunauer–Emmett Teller (BET) surface area analysis, Ultraviolet–visible spectroscopy (UV-Vis), Energy-dispersive X-ray spectroscopy (EDX), thermo gravimetric analysis (TGA) and atomic absorption spectroscopy (AAS) techniques. The synthesized catalyst was found to be a highly efficient heterogeneous nanocatalyst for multi component A3 coupling reaction of aldehyde, amine and alkyne... 

Herein, we demonstrate a facile low temperature approach to prepare a gel polymer electrolyte (GPE) based on the triiodide/iodide redox couple in a quasi-solid-state dye-sensitized solar cell (DSSC). Only one polymeric agent (i.e., hydroxypropyl cellulose (HPC)) is used for the preparation of a non-volatile GPE system for the standard liquid electrolyte containing 1-methyl-3-propylimidazolium iodide (MPII). The prepared GPE completely penetrates into a TiO2 photoanode at room temperature due to the uniform distribution of Ti, Ru and I elements in the cross-section of the electrode, forming an interpenetrating GPE/TiO2 network to access all dye molecules. The GPE with the optimum HPC : MPII... 

N-Benzyl-DABCO tribromide, a stable, solid organic ammonium tribromide, has been used as a bromine source for the regioselective and high-yielding bromination of aromatic amines and phenols. Mono-bromination proceeds well in the presence of a stoichiometric amount of bromine source at room temperature  

In this study by using a capacitive cell probe the temperature variation of the electrical properties of the water liquids is investigated. Variation of the reactance capacitance parameter of liquids with temperature in the range of 17-60°C is measured for the plain water and water mixtures. The temperature variations of the capacitance for the cool distilled and tap water samples are studied for the range of 17-29°C obtained. Present results indicate an averaged variation of 4.69 μF/°C for the distilled water and 3.24 μF/°C for tap water in warm up process to a near room temperature. The cooling behaviors for the warm mineral, tap and salt water liquids are also investigated in this study.... 

At room temperature, SO 2- 4/nano-TiO 2 efficiently catalyze the direct Mannich-type reaction of varieties of in situ-generated aldimines using aldehydes and anilines with ketones in a three-component reaction under solvent-free conditions. The reaction proceeds rapidly and affords the correspondingβ-amino ketones in good to high yields with good to excellent stereoselectivity. The catalyst can be recycled for subsequent reactions without any appreciable loss of efficiency  

Na0.3WO3 1D nanostructure forms (nanorods and nanobelts) were grown by a solid-liquid-solid mechanism from a 40 nm sputtered tungsten film deposited on a soda-lime substrate and annealed at 700 °C in a tubular furnace in N2 ambient. The morphology, structure, composition and chemical state of the prepared nanostructures were characterized by SEM, XRD, TEM, SAED and XPS measurements. The Na0.3WO3 1D nanostructures were found to have a cubic crystalline structure and grown along the [0 0 1] direction. The nanorods are a few micrometres in length and about 50 nm in diameter. The field-emission application of the prepared samples at different distances between the cathode and the anode was... 

Different microstructures were produced by heat treatment of 4340 steel. These microstructures are bainite, martensite, ferrite-martensite and ferrite-bainite. Mechanical tests were carried out at room temperature. The results showed that steel with bainite-ferrite microstructure has better ductility and charpy impact energy than steels with martensite-ferrite and full bainite microstructures. But yield and tensile strengths of this steel are less than the yield and tensile strengths of the other two steels. Hardness measurements showed that their hardness is the same. Fracture surface observations of tensile specimens showed increase in toughness of bainite-ferrite in comparison to... 

Synchronous heterogeneous catalytic hydrogenation of cyclohexene and acetone, catalyzed by Pt/Al2O3, was carried out in solutions of 2-hydroxy ethylammonium formate (a room temperature ionic liquid, RTIL) with ethanol and propan-1-ol at 25 °C. Rate constants and selectivity of the reaction (relative to cyclohexene hydrogenation) increase with mole fraction of the ionic liquid (IL). The reactants tendency to the catalyst surface increases by addition of the ionic liquid and thus the reaction rate increases, especially for cyclohexene hydrogenation. Consequently the selectivity to cyclohexene hydrogenation was increased. Single-parameter correlations of log k vs. π* (dipolarity/polarizibility)... 

In this work we report a new thermochemical method for the synthesis of ZnS:Mn nanocrystals. Zn(NO3)2 and Na2S 2O3 were used as the precursors and Mn(NO 3)2 was the source of impurity. Thioglycerol (TG,C 3H8O2S) was also used as the capping agent and the catalyst of the reaction. Na2S2O3 is a heat sensitive material which releases S species upon heating. Consequently, the reaction proceeds in temperatures higher than room temperature. The reaction was done in two steps. In the first step, the precursors were heated at 96 °C for an hour without TG. In the second step, TG was injected to the solution and the heating process was continued for longer heating durations. A fast growth occurred in...