Sharif Digital Repository

The diffusion and deposition of TiO2 nanoparticles in EOR application was investigated in this paper. TEM image of nanoparticles showed that the particles are elongated with average long and short axis sizes of 54 and 15 nm. Water flooding tests showed that the recovery factor can be improved from 49% to 80% using TiO2 nanoparticles. Viscosity and interfacial tension measurements showed that by using TiO2 nanoparticles the viscosity of injected fluid and interfacial tension do not change significantly and can not explain the change in recovery factor. Contact angle measurements showed that nanoparticles deposition changed the wettability of the rock surface from oil-wet to water-wet. SEM... 

This paper studies a WAG process for improving the recovery efficiency in light oil reservoirs. Until now, few references have reported the role of CO2 mole percent on recovery improvement in light oil reservoirs. The injected gas was changed, and the effect of composition changes on performance of core flood experiments were conducted at fixed flow rate. Five series of experiments (varied in methane mole percentages, 0, 25, 50, and 75, 100) were systematically examined. The results indicated that the oil recovery efficiency improved with the increasing of CO2 mole ratio and there was also maximum recovery efficiency in this work. That would be helpful to better understanding the role of CO2... 

CO2 gas injection is known as one of the most popular enhanced oil recovery techniques for light and medium oil reservoirs, therefore providing an acceptable mass transfer mechanism for CO2–oil systems seems necessary. In this study, interfacial mass transfer coefficient has been evaluated for CO2–normal heptane and CO2–normal hexadecane systems using equilibrium and dynamic interfacial tension data, which have been measured using the pendant drop method. Interface mass transfer coefficient has been calculated as a function of temperature and pressure in the range of 313–393 K and 1.7–8.6 MPa, respectively. The results showed that the interfacial resistance is a parameter that can control... 

A literature review of laboratory and field scale studies on low salinity water (LSW) injection showed that the salinity and composition of injected water can have a significant impact on oil recovery. Historically, extensive research has been completed to understand the mechanisms and factors affecting LSW injection. However, although numerous mechanisms have been proposed to describe the interactions in the target process, none have been widely accepted. In this study, waterflooding tests were used to investigate the advantages, disadvantages, and effect of LSW injection. In laboratory tests, two different brines and crude oil of one of Iran's southern reservoirs were used to assess the... 

In addition to reducing carbon dioxide (CO2) emission, the high oil recovery efficiency achieved by CO2 injection processes makes CO2 injection a desirable enhance oil recovery (EOR) technique. Minimum miscibility pressure (MMP) is an important parameter in successful designation of any miscible gas injection process such as CO2 flooding; therefore, its accurate determination is of great importance. The current experimental techniques for determining MMP are expensive and time-consuming. In this study, multi-gene genetic programming has been combined with constrained multivariable search methods, and a simple empirical model has been developed which provides a reliable estimation of MMP in a... 

Smart water injection is determined as an effective EOR process to change the wettability and interfacial tension for better micro/macro sweep efficiencies. This water contains reactive ions such as Mg ∧(2+), Ca ∧(2+) and SO-4 ∧(2-) which can act as potential determining ions and change the surface charge of calcite rocks. One of the major concerns in the execution of an effective waterflood, especially in tight carbonate reservoirs, is the incompatibility between the formation brine and the injecting water. This research work aims to investigate the most important challenge of waterflooding process related to the possible formation damage because of inorganic scale deposition during... 

In the optimization of naturally fractured reservoirs, it is required to take into account their complex flow behavior due to high conductivity fractures. In this regard, the possible effects of fractures must be included in the optimization procedure. In a water-flooding project, fast water breakthrough from injection to production wells may be occurred because of high permeability fractures. To consider the effect of the fracture system, a multi-criterion optimization procedure is proposed in this work. For this contribution, Non-dominated Sorting Genetic Algorithm version II (NSGA-II) is implemented for the optimization purposes. Considering the effect of the fracture system on the flow... 

It has long been understood that flow behavior in heterogeneous porous media is largely controlled by the continuity of permeability contrasts. With this in mind, we are looking in new methods for a fast estimation of the effective permeability which concentrates on the properties of the percolating cluster. From percolation concepts we use a threshold permeability value (Kth) by which the gridblocks with the highest permeability values connect two opposite side of the system in the direction of the flow. Those methods can be applied to heterogeneous media of a range of permeabilities distribution and various underlying structures. We use power law relations and weighted power averages that... 

An upscaling method such as renormalization converts a detailed geological model to a coarse one. Although flow equations can be solved faster on a coarse model, its results have more errors. Numerical dispersion, heterogeneity loss, and connectivity misrepresentation are the factors responsible for errors. Connectivity has a great effect on the fluid distribution and leakage pathways in EOR processes or CO2 storage. This paper deals with the description and quantification of connectivity misrepresentation in the upscaling process. For detection of high-flow regions, the flow equations are solved under simplified single-phase conditions. These regions are recognized as the cells whose fluxes... 

This work aims to discuss the results of wide ranges of laboratory investigations to evaluate the performance of a newly-formulated surfactant for heavy oil reservoirs in order to improve the microscopic sweep efficiency after water flooding processes. In the first part, the specific behavior of the formulated surfactant including its salinity tolerance, interfacial tension, and optimum performance window was determined. Then, the application of surfactant solutions in real sandstone reservoir rocks was assessed for both oil-wet and water-wet cases. Besides, the effect of changing the capillary and viscous forces and interfacial tension on the residual phase saturations were characterized.... 

In recent years, polysilicon nanoparticles are used to enhance the oil recovery through the water injection process in oilfields. The contributing mechanisms are the reduction of interfacial tension and wettability alteration which lead to improving or decreasing the oil phase relative permeability and can be traced by change of relative permeability curves. However, profound understanding of the effect of dispersed nano-silica particles on the hysteretic behavior of relative permeability curves remains a controversy topic in the literature.The current study illustrates the influence of dispersed silica particles on hysteretic trend of two-phase curves of oil-water relative permeability.... 

Nitrogen has emerged as a competitive gas injection alternative for gas-based enhanced oil recovery processes in the past two decades. The injection of nitrogen into the reservoirs has improved the oil recovery efficiency in various oil reservoirs from heavy to volatile oils. As it is known, interfacial tension (IFT) plays a key role in any enhanced oil recovery process, particularly gas injection processes; therefore, its accurate determination is crucial for the design of any gas injection process especially at reservoir condition. In this study, an axisymmetric drop shape analysis (ADSA) was utilized to measure the equilibrium IFTs between crude oil and N2 at different temperature levels... 

Optimization of any production operation is a tool for increasing production rates and reducing production costs. Water flooding is one of the techniques that frequently be used to increase oil recovery after primary depletion. A methodology for optimizing the production by using the net present value of a heterogeneous reservoir under water flooding has been presented, which is based on controlling the bottomhole pressures of the production wells, using smart well technology. For this purpose, a numerical flow simulator is coupled with an optimization program. The technique was implemented on a synthetic two dimensional oil reservoir with heterogeneous permeability. This optimization... 

Dilute Surfactant flooding has been recognized as one of the significant processes in chemical flooding. Many oil reservoirs became appropriate candidates for surfactant/water flooding when screening criteria was developed. Injected surfactant tried to mobilize the residual oil that was trapped in interstice. The main contributing mechanism to enhance oil recovery by surfactant flooding was defined as rock wettability alteration. Wettability is one of the substantial parameters to choose the best approach for a successful surfactant flooding in which tiny change in wettability will lead to improve oil recovery fundamentally. In this experimental study the effect of different aging time and... 

Alkaline-Surfactant-Polymer flooding is one of the most novel chemical enhanced oil recovery methods in the petroleum industry. This method has attracted interest due to its remarkable advantages. In this work, a series of ASP floods are conducted on fractured/non-fractured carbonate rocks. The performance of the tests was investigated by various ASP floods consisting of five types of polymers, two surfactants and one common alkaline. ASP was flooded simultaneously and sequentially in four defined scenarios after water flooding. The results showed that although using hydrolysed polymers increases the recovery factor in the fractured medium, sulfonated polymers increase oil recovery even more... 

The use of adjusted/optimized saline water categorized into two different classes namely smart water (SW) and low salinity (LoSal) water injection has been proposed for more oil recovery from specific types of oil reservoirs. There are possible mechanisms concerning SW flooding that have been proposed in the literature, some of them are still subject to more examination. In this study, an experimental investigation is performed to determine the influence of type and amount of salt to the surface properties including interfacial tension (IFT) and contact angle (CA) of aqueous solution + acidic and asphaltenic crude oil + carbonate rock systems. For this purpose, the concentration of different... 

As the oil production from conventional oil reservoirs is decreasing, oil production through Enhanced Oil Recovery (EOR) processes is supposed to compensate for both the oil production reduction in matured oil reservoirs and the worldwide dramatic increase in oil demand. Therefore, developing a strategy to choose an optimized EOR technique is crucial to find a resolution for production decline in oil reservoirs. A screening tool recommending the most appropriate EOR method is proposed in this study. An expert fuzzy logic system is employed to screen four well-known EOR methods including miscible CO2 injection, miscible HC gas injection, polymer flooding and steam injection based on the... 

Although alkaline-surfactant-polymer flooding is proved to be efficient for oil recovery from heavy oil reservoirs, the displacements mechanism/efficiency of this process in fractured systems needs to more discussion, especially in five-spot patterns. In this work, several ASP flooding test were performed on fractured micromodels which were initially saturated with heavy oil at constant flow rate and different fracture geometrical characteristics conditions. The ASP solutions are constituted from 5 polymers i.e. four synthetic polymers include three hydrolyzed polyacrylamide with different molecular weight as well as a non-hydrolyzed polyacrylamide and a biopolymer, 2 surfactants i.e. a... 

This paper summarizes the possibility of carbon dioxide gas Injection and compares the results with natural depletion in one of Iranian under saturated oil reservoir. At first with using PVTi software and Eclipse simulator, slim tube test has been simulated and Minimum Miscibility Pressure (MMP) of carbon dioxide gas with reservoir fluid determined then simulation of CO2 injection had done and at the end assessment of economic conditions for CO2 injection had been considered. Results had shown CO2 is an optimized choice for gas injection in this oil reservoir  

This work concerns with experimental investigation of CO2 WAG injection to light crude oil in near miscible conditions which has been rarely attended in the available literature. Here, several core flood experiments at three constant injection rates and four WAG ratios are conducted on sandstone rocks saturated with light crude oil in presence of saline water. The results showed that higher injection rate has a better performance regarding oil recovery for smaller PVs of injected fluids, while lower injection rate showed higher ultimate recovery for a 30% increase in injected PVs. Secondary continuous gas injection showed a superior performance than all the other WAG injections in different...