Sharif Digital Repository

We present sliding experiments of a sledge on wetted sand and describe that the frictional response is controlled by the penetration hardness of the granular medium. Adding a small amount of water to sand increases the hardness which results in a decrease of the sliding friction. Pouring even more water to sand results in a decrease of the hardness and a subsequent increase of the friction. This inverse correlation between hardness of a wetted granular material and its frictional response to sliding is found to be due to ploughing of the sledge. When the load of the sledge exceeds the penetration hardness of the water-sand mixture the granular material is irreversibly deformed, which is... 

Supersonic separators (3Ss) are applied in gas separation processes. Two-dimensional simulation is employed to investigate the effect of operational and thermophysical parameters on the shockwave position. In addition, the impact of the cyclonic part and wet outlet geometry is evaluated by proposing four cases. Increasing the length of the cyclonic part exerts positive and negative influences on the performance of the 3S and the pressure recovery coefficient, respectively. The optimum length is determined between 10 and 15 cm. To demonstrate negative effects of wasted air from the wet outlet, its flow has been increased from 3.6 to 8.1 % of the inlet flow. Improved performance of the 3S is... 

In order to understand the potential role of divalent ions involved in smart water, fluid-fluid and rock-fluid interactions are studied through contact angle and interfacial tension (IFT) measurements. Then, the suitable brines in changing contact angle and IFT are brought into measurement with spontaneous imbibition experiments to evaluate the co-impact of fluid-fluid and rock-fluid interactions. The results show the importance of SO42− ions during smart water injection as removing them from the injection water leads to a sharp drop in ultimate oil recovery. Accordingly, when the concentration of SO42− within the injection water increases four times, 10% ultimate oil recovery is recovered.... 

In this study, a three-dimensional tablet-like porous scaffold, comprising core-shell fibers to host proteins inside the core, was developed. The fabrication method involved the novel combination of coaxial and wet electrospinning in a single setting. Poly (ε-caprolactone) was chosen as the based polymer and bovine serum albumin was used as a model protein. These 3D tablet-like scaffolds exhibited adequate porosity and suitable pore size for cell culture and cell infiltration, in addition to appropriate mechanical properties for cartilage tissue engineering. The effects of different parameters on the behavior of the system have been studied and the 3D scaffold based on the core-shell fiber... 

Abstract: Further to traditional corrosion monitoring techniques for rated deteriorations, nowadays modern electrochemical monitoring methods are promising for the control of non-rated damage mechanisms. Considering carbon steel as the most commonly used alloy in the oil and gas industry, there are special grades under NACE MR0175 standard which are immune to sour corrosion. However, according to the industry reports, their immunity can be terminated by upset conditions or on site repairs. This issue will impose either a high operational risk or exorbitant maintenance and inspection costs. Hence, in this paper, a new monitoring technology framework is discussed to lessen a catastrophic... 

An intense decrease in cycling performance and safety is a challenge for elevated temperature application of LiNi0.5Co0.2Mn0.3O2 (NCM) cathode material. In this paper, effect of two types of nano-coatings on improvement of elevated temperature performance of NCM cathode material has been investigated. One of the coatings contains SiO2 nanoparticles and the other one contains composite of reduced graphene oxide and SiO2 nanoparticles (rGO-SiO2). The coatings were fabricated by a facile wet chemical method. The SiO2 coated cathode material showed an excellent elevated temperature cycling stability, however, a decrease in discharge capacity and rate capability of this sample was observed. On... 

The low salinity water injection has become one of the most important studies in the oil industry for improving oil recovery compared to conventional seawater injection. Thus, extensive studies have been conducted in carbonate and sandstone reservoirs to investigate how the physical properties of rocks and the chemical composition of fluids influence low salinity effect, while, the carbonate reservoir rocks requires more investigation of the effect of molecular and/or ionic interactions. In this experimental work, the effectiveness of various water flooding schemes in carbonate reservoir rock samples is investigated. In this regard, the oil recovery potential of seawater (SW), reservoir... 

Engineered water (EW) flooding is one of the enhanced oil recovery (EOR) techniques in carbonate reservoirs. In this method, the wettability of reservoir rock is altered by controlling the amount of various ions in the injected brine. The thermodynamics of wettability is related to the surface interactions and stability of water film on a rock surface. It can be identified by calculating disjoining pressure isotherms. In this study, core flooding tests, contact angle and zeta potential measurements along with the disjoining pressure isotherm calculation by the DLVO theory were used to investigate the wettability alteration of dolomite rock. Four brines include reservoir formation water... 

Low Salinity Waterflooding (LSWF) has become a popular tertiary injection EOR method recently. Both fluid-fluid and fluid-rock interactions are suggested as the contributing mechanisms on the effectiveness of LSWF. Considering the contradictory remarks in the literature, the dominating mechanisms and necessary conditions for Low Salinity Effect (LSE) varies for different crude oil-brine-rock (CBR) systems. The aim of the present study is to investigate LSE for an oil field in the Middle East that is composed of separate sandstone and limestone layers. Contact angles and Interfacial Tension (IFT) are measured to have more insight on the CBR under investigation. Visual experiments were... 

Gas flooding is a practical secondary scenario for enhanced oil recovery. Channeling and fingering of the injected gas are the major problems facing this technique. These challenges can be mitigated by the injection of gas as foam. However, foam stability influences the overall efficiency of the process, which could be improved by nanoparticles (NPs). This work provides a theoretical and experimental analysis of the NPs wettability effects on foam behavior, in both static and dynamic states. The treated calcite (CaCO3) NPs along with a cationic surfactant (HTAB) were used for this purpose. By comparison of theoretical and experimental data, it was shown that the foam stability in the... 

Foam flooding has been applied as a promising method in enhanced oil recovery to obviate the challenges of gas flooding such as fingering, channeling and overriding. However, long-term foam stability is crucial for mobility control. In this work, the effective mechanisms on foam stability in the presence of CaCO3 nanoparticles were assessed both theoretically and experimentally. The static and dynamic behaviors of cationic surfactant (HTAB) foam in the presence of CaCO3 nanoparticles with different hydrophobicity were evaluated. The CaCO3 nanoparticles were treated with a series of long-chain fatty acids to generate a range of wettability. Afterward, the underlying mechanisms were revealed... 

Solar stills are considered an environmentally friendly technique to produce fresh water. The condensation surface plays an essential role in controlling the efficiency of the solar still. This main parameter is critically affected by the wettability of the condensation surface that affects the condensation mechanism, namely drop-wise or film-wise condensation. This study aims to enhance the efficiency of solar stills by altering the surface wettability hence changing the condensation mechanism using nanomaterials. In this experimental work, different condensation surfaces were coated by silicone nanoparticles to change the condensation mechanism from film to dropwise. Scanning electron... 

The condensation process is of great importance in many heat transfer devices in which a large amount of energy must be transferred. Furthermore, condensation is a crucial part of energy conversion and affects the energy efficiency of thermal desalination plants and solar stills. During the condensation process in solar stills, an essential part of the energy is transferred through the condensation surface to produce fresh water. Therefore, the condensation surface plays a significant role in the working efficiency of solar stills. The wettability of the condensation surface influences the condensation mechanism, which, in turn, affects the efficiency of solar stills. This study aims to... 

In the present study, the effect of two different kinds of surfactants namely conventional (Sodium dodecyl benzene sulfonate (SDBS)) and ionic liquid (IL)-based surfactants are investigated on the tertiary oil recovery using relative permeability concept. In this way, besides the Amott wettability index measurement, unsteady state core flooding tests are performed to not only find the effect of surfactant injection on tertiary oil recovery, but also to investigate their effects on relative permeability of carbonate rocks. In addition, for more reliable conclusions regarding the possible mechanisms, interfacial tension (IFT), compatibility and emulsification tests are carried out as a... 

The objective of this study is to calibrate Priestley-Taylor (PT) model for estimating open water evaporation from an arid region reservoir called Chahnimeh. Chahnimeh Reservoir which is situated in the Sistan area in the southeast of Iran is being affected by regional energy advection during May to October. Therefore, common models of open water evaporation estimation such as PT require calibration. PT method was calibrated for Chahnimeh Reservoir using a volume balance method. Results showed that PT coefficient, αPT, as a constant over the year varies between 2.47±0.09 and 1.20±0.03 for two different hydrologic conditions of dry and wet. It means that there is also an intra-annular... 

In this article, the design and operation of a cylindrical capacitive sensor based on the dielectric reactance capacitance and conductance changes of the gap medium is reported. The proposed system was used to determine characteristics of different water liquids as a result of the capacitance and resistance variations. The air gap capacitance (dry signal) is measured and then by filling the gap with a liquid, the capacitance (wet signal) is monitored for different liquids. A reported sensor is used for the distilled, tap, boiled, and salt water measurements and the capacitance and resistance results are compared. A big difference of about 38.5 μF in the measured capacitance values for the... 

In this report, sessile drop technique was employed to study the wetting of alumina by pure aluminium. Contact angle of pure aluminium on the surface of polycrystalline alumina substrate was studied in the temperature range of 750-1100 °C. Electron microscopy and EDX analysis were employed to examine the possible reactions at the melt-substrate interface. It was found that at temperatures in excess of 1050 °C molten aluminium can wet alumina. No reaction layer was detected at the Al/Al2O3 interface. © 2007 Elsevier B.V. All rights reserved  

Two main reservoir mechanisms that impact oil recovery factors are wettability alteration and interfacial tension (IFT) change. In this study, these two key mechanisms are evaluated experimentally for samples from the Asmari (carbonate) oil reservoir utilizing silica nanoparticles in the presence of low-salinity water. The nanofluid, rock formation and crude oil samples were prepared meticulously to ensure meaningful experimental could be conducted over a range of low-salinity conditions. The results show that across the range of salinities studied, the absolute value of zeta potential of nanofluids decreases with increasing total dissolved solids (TDS) in the water treated with silica... 

Several lattice Boltzmann models for multi-phase flow have been developed, but few of them are capable of modeling fluid flows with high density ratio in the order of 1000. Therefore, an advanced chromodynamics, Rothmann-Keller (RK) type model is employed in current study, which can handle liquid-gas density ratio in the order of 1000 and viscosity ratio in the order of 100. Other distinctive characteristics of the proposed model are high stability, and capability of setting parameters such as surface tension independently. In spite of these benefits, the original RK model fails to model wetting tendency of the fluids. As a result, it is impossible to correctly simulate two-fluid phase flow...