Sharif Digital Repository

The problem of joint design of transmit code and receive filter is considered in many application scenarios of multiple input multiple output (MIMO) radar systems. The performance of the joint design problem is evaluated with the signal-to-interference ratio (SINR) metric in the presence of noise. In such problems, the optimization problem is to maximize SINR on the receiver side with the constraints that are applied on the transmitted waveform. Our proposed method, RTR, is a manifold-based geometric method that performs better than the SDP method in terms of algorithm execution speed and calculation complexity. For simulation, we took sampled and real TIR with Target Aspect Angle (TAA) in a... 

Reinforced concrete is one of the most important structural materials used in the construction industry worldwide. Nevertheless, certain physical and chemical factors in the service environment can contribute to its deterioration and failure. One of the most significant factors is the reinforcing steel bar (rebar) corrosion. In order to minimize the rebars corrosion, different kinds of coatings were investigated and evaluated by scientists. In this investigation comparative studies were performed on two different kinds of coated rebars (zinc-rich epoxy and polyamide epoxy coated rebars) and uncoated rebar. In order to evaluate these reinforced concretes, the adhesion, durability, thickness... 

In this thesis, a model is presented to detect and monitor the rotor bar's condition of large motors. This proposed model uses two diagnostic methods MCSA and ZCT, to extract the fault components. The input of the proposed model is only the motor current at two levels of 80% and 100% of the nominal motor load, which by using the two methods MCSA and ZCT and making changes in how to use them can be the disadvantages of other methods such as incorrect detection of rotor bars in Large motors with variable load, the harmonical stator voltage (or the presence of the drives) and asymmetric conditions. The extracted components are classified using two learnable algorithms, the k-NN algorithm and... 

Production logging consists of running measurement instruments called logging tools into an oil or gas well to measure various parameters such as temperature, flow velocity, pressure, density, etc. The primary purpose for production logging is to allow enhancing production profits and decreasing costs. Nowadays the common way for fluid density measurement as a part of these tools depends on radioactive source. Special considerations must be taken upon the use of this principle due to its radioactive character. This thesis is focused on a non-radioactive method of determining density. The subject of this thesis is to consider methods for measuring density based on principle of acoustic... 

Sonic and ultrasonic measurements are used for checking status of wells. Well logging is used to estimate well specifications like borehole diameter, casing thickness, cement bond quality and cement sheath thickness. In this thesis, some reported works in field of sonic/ultrasonic measurement of oil wells are reviewed and results of software implementation of ultrasonic measurement with pitch-catch arrangement, pulse-echo arrangement and phased array arrangement are presented. ultrasonic measurement with pitch-catch arrangement uses one transducer for transmitting ultrasonic waves and two transducers (in different distances) for receiving ultrasonic waves. Ultrasonic measurement with... 

In the oil industry, a better understanding of the well condition leads to improve the management and increase the oil production. Production logging tools is a set of tools for measuring different parameters such as density, diameter and flow in oil and gas wells. These tools are considered among high-tech tools in the oil industry. The reason is that they should work in harsh conditions, i.e. high temperature about 170 ° C and pressure around 15000 psi, and at the same time give an accurate measurement of the quantity. Current production-logging tools measure the fluid velocity and the diameter of an oil well by individual mechanical tools, and the density by a radioactive densitometer. ... 

The objective of this research is evaluating the effect of filler type and content on the characteristics of asphaltic materials. The properties of the asphalt mixture are greatly influenced by its components. As asphalt mixtures are composed of two prominent components, aggregates and binder, the change in type and contents of these materials may lead to altering the performance of asphalt mixtures. Aggregates in the asphalt mixtures are categorized into three groups based on their particle sizes: coarse aggregate, fine aggregate and mineral filler. The effect of filler on the characteristics of asphalt mixtures can be examined by changing the type and content of filler and holding the... 

Most of the time there are three different materials in oil wells; Oil, water and gas. Measuring volume percentage and flow of the individual materials (phases) is an important issue, due to their critical role in extraction process control. Measuring tool should be able to measure flow and percentage of each phase in a case that they are separated (in deviated wells due to gravity). In addition, the measurement should be carried on in a high temperature and high pressure environment and in presence of corrosive substances. Most of previous researches on Multi-Phase Flow Meter (or MPFM) led to mechanical methods to measure flow and they usually use electrical impedance or permittivity for... 

This study aimed to investigate the efficiency of machine learning algorithms in capturing the dynamics of water particles' age distribution and in estimating the time series of median travel time (MTT) in river basins. The mechanism of solute transport in a catchment does not follow the hydrograph shape of the catchment and depends on the spatial and temporal distribution of solute resident time. The equations governing the age dynamics of water particles discharged from a catchment have been presented analytically in recent research. These equations showed that the transfer of solutes depends on various factors, including climatic conditions, basin topography, and basin vegetation. Also,... 

Clustering algorithms are developed to provide general attitudes on database, recognizing latent structures and their more effective accessibility. Recently, broad studies are conducted on clustering since it is recognized as an important tool to explore and analyze data. Clustering is a fundamental learning operation without monitoring in data exploration which divides data into groups of objects so that objects in one group have the most similarity to each other and lowest similarity to objects in other groups. Some clustering algorithms such fuzzy clustering model (FCM) are widely used in clustering problem solution although this technique addresses local optimized searches. Additionally,... 

Current trend of energy consumption and aging infrastructure of electricity grids mandates high amounts of investment in transmission and distribution networks. On the other hand, with increased awareness about environmental issues, share of renewable energy resources in power generation portfolio has risen in recent years. Microgrids, as one of the most promising solutions to tackle these issues, are able to accommodate high penetration levels of renewable energy sources and distributed generation in distribution systems. However, microgrids sizes are limited due to some operational considerations and as a result, efficient management of distribution systems with high penetration of...